| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20170619152035.960963673@linuxfoundation.org>
Date: Mon, 19 Jun 2017 23:20:48 +0800
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Anssi Hannula <anssi.hannula@...wise.fi>,
"David S. Miller" <davem@...emloft.net>,
Sasha Levin <alexander.levin@...izon.com>
Subject: [PATCH 3.18 04/32] net: xilinx_emaclite: fix freezes due to unordered I/O
3.18-stable review patch. If anyone has any objections, please let me know.
------------------
From: Anssi Hannula <anssi.hannula@...wise.fi>
[ Upstream commit acf138f1b00bdd1b7cd9894562ed0c2a1670888e ]
The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af87 ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@...wise.fi>
Fixes: 123c1407af87 ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@...emloft.net>
Signed-off-by: Sasha Levin <alexander.levin@...izon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/net/ethernet/xilinx/xilinx_emaclite.c | 116 +++++++++++++-------------
1 file changed, 62 insertions(+), 54 deletions(-)
--- a/drivers/net/ethernet/xilinx/xilinx_emaclite.c
+++ b/drivers/net/ethernet/xilinx/xilinx_emaclite.c
@@ -100,6 +100,14 @@
/* BUFFER_ALIGN(adr) calculates the number of bytes to the next alignment. */
#define BUFFER_ALIGN(adr) ((ALIGNMENT - ((u32) adr)) % ALIGNMENT)
+#ifdef __BIG_ENDIAN
+#define xemaclite_readl ioread32be
+#define xemaclite_writel iowrite32be
+#else
+#define xemaclite_readl ioread32
+#define xemaclite_writel iowrite32
+#endif
+
/**
* struct net_local - Our private per device data
* @ndev: instance of the network device
@@ -158,15 +166,15 @@ static void xemaclite_enable_interrupts(
u32 reg_data;
/* Enable the Tx interrupts for the first Buffer */
- reg_data = __raw_readl(drvdata->base_addr + XEL_TSR_OFFSET);
- __raw_writel(reg_data | XEL_TSR_XMIT_IE_MASK,
- drvdata->base_addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(drvdata->base_addr + XEL_TSR_OFFSET);
+ xemaclite_writel(reg_data | XEL_TSR_XMIT_IE_MASK,
+ drvdata->base_addr + XEL_TSR_OFFSET);
/* Enable the Rx interrupts for the first buffer */
- __raw_writel(XEL_RSR_RECV_IE_MASK, drvdata->base_addr + XEL_RSR_OFFSET);
+ xemaclite_writel(XEL_RSR_RECV_IE_MASK, drvdata->base_addr + XEL_RSR_OFFSET);
/* Enable the Global Interrupt Enable */
- __raw_writel(XEL_GIER_GIE_MASK, drvdata->base_addr + XEL_GIER_OFFSET);
+ xemaclite_writel(XEL_GIER_GIE_MASK, drvdata->base_addr + XEL_GIER_OFFSET);
}
/**
@@ -181,17 +189,17 @@ static void xemaclite_disable_interrupts
u32 reg_data;
/* Disable the Global Interrupt Enable */
- __raw_writel(XEL_GIER_GIE_MASK, drvdata->base_addr + XEL_GIER_OFFSET);
+ xemaclite_writel(XEL_GIER_GIE_MASK, drvdata->base_addr + XEL_GIER_OFFSET);
/* Disable the Tx interrupts for the first buffer */
- reg_data = __raw_readl(drvdata->base_addr + XEL_TSR_OFFSET);
- __raw_writel(reg_data & (~XEL_TSR_XMIT_IE_MASK),
- drvdata->base_addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(drvdata->base_addr + XEL_TSR_OFFSET);
+ xemaclite_writel(reg_data & (~XEL_TSR_XMIT_IE_MASK),
+ drvdata->base_addr + XEL_TSR_OFFSET);
/* Disable the Rx interrupts for the first buffer */
- reg_data = __raw_readl(drvdata->base_addr + XEL_RSR_OFFSET);
- __raw_writel(reg_data & (~XEL_RSR_RECV_IE_MASK),
- drvdata->base_addr + XEL_RSR_OFFSET);
+ reg_data = xemaclite_readl(drvdata->base_addr + XEL_RSR_OFFSET);
+ xemaclite_writel(reg_data & (~XEL_RSR_RECV_IE_MASK),
+ drvdata->base_addr + XEL_RSR_OFFSET);
}
/**
@@ -323,7 +331,7 @@ static int xemaclite_send_data(struct ne
byte_count = ETH_FRAME_LEN;
/* Check if the expected buffer is available */
- reg_data = __raw_readl(addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_TSR_OFFSET);
if ((reg_data & (XEL_TSR_XMIT_BUSY_MASK |
XEL_TSR_XMIT_ACTIVE_MASK)) == 0) {
@@ -336,7 +344,7 @@ static int xemaclite_send_data(struct ne
addr = (void __iomem __force *)((u32 __force)addr ^
XEL_BUFFER_OFFSET);
- reg_data = __raw_readl(addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_TSR_OFFSET);
if ((reg_data & (XEL_TSR_XMIT_BUSY_MASK |
XEL_TSR_XMIT_ACTIVE_MASK)) != 0)
@@ -347,16 +355,16 @@ static int xemaclite_send_data(struct ne
/* Write the frame to the buffer */
xemaclite_aligned_write(data, (u32 __force *) addr, byte_count);
- __raw_writel((byte_count & XEL_TPLR_LENGTH_MASK),
- addr + XEL_TPLR_OFFSET);
+ xemaclite_writel((byte_count & XEL_TPLR_LENGTH_MASK),
+ addr + XEL_TPLR_OFFSET);
/* Update the Tx Status Register to indicate that there is a
* frame to send. Set the XEL_TSR_XMIT_ACTIVE_MASK flag which
* is used by the interrupt handler to check whether a frame
* has been transmitted */
- reg_data = __raw_readl(addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_TSR_OFFSET);
reg_data |= (XEL_TSR_XMIT_BUSY_MASK | XEL_TSR_XMIT_ACTIVE_MASK);
- __raw_writel(reg_data, addr + XEL_TSR_OFFSET);
+ xemaclite_writel(reg_data, addr + XEL_TSR_OFFSET);
return 0;
}
@@ -381,7 +389,7 @@ static u16 xemaclite_recv_data(struct ne
addr = (drvdata->base_addr + drvdata->next_rx_buf_to_use);
/* Verify which buffer has valid data */
- reg_data = __raw_readl(addr + XEL_RSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_RSR_OFFSET);
if ((reg_data & XEL_RSR_RECV_DONE_MASK) == XEL_RSR_RECV_DONE_MASK) {
if (drvdata->rx_ping_pong != 0)
@@ -398,14 +406,14 @@ static u16 xemaclite_recv_data(struct ne
return 0; /* No data was available */
/* Verify that buffer has valid data */
- reg_data = __raw_readl(addr + XEL_RSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_RSR_OFFSET);
if ((reg_data & XEL_RSR_RECV_DONE_MASK) !=
XEL_RSR_RECV_DONE_MASK)
return 0; /* No data was available */
}
/* Get the protocol type of the ethernet frame that arrived */
- proto_type = ((ntohl(__raw_readl(addr + XEL_HEADER_OFFSET +
+ proto_type = ((ntohl(xemaclite_readl(addr + XEL_HEADER_OFFSET +
XEL_RXBUFF_OFFSET)) >> XEL_HEADER_SHIFT) &
XEL_RPLR_LENGTH_MASK);
@@ -414,7 +422,7 @@ static u16 xemaclite_recv_data(struct ne
if (proto_type > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
if (proto_type == ETH_P_IP) {
- length = ((ntohl(__raw_readl(addr +
+ length = ((ntohl(xemaclite_readl(addr +
XEL_HEADER_IP_LENGTH_OFFSET +
XEL_RXBUFF_OFFSET)) >>
XEL_HEADER_SHIFT) &
@@ -436,9 +444,9 @@ static u16 xemaclite_recv_data(struct ne
data, length);
/* Acknowledge the frame */
- reg_data = __raw_readl(addr + XEL_RSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_RSR_OFFSET);
reg_data &= ~XEL_RSR_RECV_DONE_MASK;
- __raw_writel(reg_data, addr + XEL_RSR_OFFSET);
+ xemaclite_writel(reg_data, addr + XEL_RSR_OFFSET);
return length;
}
@@ -465,14 +473,14 @@ static void xemaclite_update_address(str
xemaclite_aligned_write(address_ptr, (u32 __force *) addr, ETH_ALEN);
- __raw_writel(ETH_ALEN, addr + XEL_TPLR_OFFSET);
+ xemaclite_writel(ETH_ALEN, addr + XEL_TPLR_OFFSET);
/* Update the MAC address in the EmacLite */
- reg_data = __raw_readl(addr + XEL_TSR_OFFSET);
- __raw_writel(reg_data | XEL_TSR_PROG_MAC_ADDR, addr + XEL_TSR_OFFSET);
+ reg_data = xemaclite_readl(addr + XEL_TSR_OFFSET);
+ xemaclite_writel(reg_data | XEL_TSR_PROG_MAC_ADDR, addr + XEL_TSR_OFFSET);
/* Wait for EmacLite to finish with the MAC address update */
- while ((__raw_readl(addr + XEL_TSR_OFFSET) &
+ while ((xemaclite_readl(addr + XEL_TSR_OFFSET) &
XEL_TSR_PROG_MAC_ADDR) != 0)
;
}
@@ -642,32 +650,32 @@ static irqreturn_t xemaclite_interrupt(i
u32 tx_status;
/* Check if there is Rx Data available */
- if ((__raw_readl(base_addr + XEL_RSR_OFFSET) &
+ if ((xemaclite_readl(base_addr + XEL_RSR_OFFSET) &
XEL_RSR_RECV_DONE_MASK) ||
- (__raw_readl(base_addr + XEL_BUFFER_OFFSET + XEL_RSR_OFFSET)
+ (xemaclite_readl(base_addr + XEL_BUFFER_OFFSET + XEL_RSR_OFFSET)
& XEL_RSR_RECV_DONE_MASK))
xemaclite_rx_handler(dev);
/* Check if the Transmission for the first buffer is completed */
- tx_status = __raw_readl(base_addr + XEL_TSR_OFFSET);
+ tx_status = xemaclite_readl(base_addr + XEL_TSR_OFFSET);
if (((tx_status & XEL_TSR_XMIT_BUSY_MASK) == 0) &&
(tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
tx_status &= ~XEL_TSR_XMIT_ACTIVE_MASK;
- __raw_writel(tx_status, base_addr + XEL_TSR_OFFSET);
+ xemaclite_writel(tx_status, base_addr + XEL_TSR_OFFSET);
tx_complete = true;
}
/* Check if the Transmission for the second buffer is completed */
- tx_status = __raw_readl(base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET);
+ tx_status = xemaclite_readl(base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET);
if (((tx_status & XEL_TSR_XMIT_BUSY_MASK) == 0) &&
(tx_status & XEL_TSR_XMIT_ACTIVE_MASK) != 0) {
tx_status &= ~XEL_TSR_XMIT_ACTIVE_MASK;
- __raw_writel(tx_status, base_addr + XEL_BUFFER_OFFSET +
- XEL_TSR_OFFSET);
+ xemaclite_writel(tx_status, base_addr + XEL_BUFFER_OFFSET +
+ XEL_TSR_OFFSET);
tx_complete = true;
}
@@ -700,7 +708,7 @@ static int xemaclite_mdio_wait(struct ne
/* wait for the MDIO interface to not be busy or timeout
after some time.
*/
- while (__raw_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET) &
+ while (xemaclite_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET) &
XEL_MDIOCTRL_MDIOSTS_MASK) {
if (time_before_eq(end, jiffies)) {
WARN_ON(1);
@@ -736,17 +744,17 @@ static int xemaclite_mdio_read(struct mi
* MDIO Address register. Set the Status bit in the MDIO Control
* register to start a MDIO read transaction.
*/
- ctrl_reg = __raw_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET);
- __raw_writel(XEL_MDIOADDR_OP_MASK |
- ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg),
- lp->base_addr + XEL_MDIOADDR_OFFSET);
- __raw_writel(ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK,
- lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ ctrl_reg = xemaclite_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ xemaclite_writel(XEL_MDIOADDR_OP_MASK |
+ ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg),
+ lp->base_addr + XEL_MDIOADDR_OFFSET);
+ xemaclite_writel(ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK,
+ lp->base_addr + XEL_MDIOCTRL_OFFSET);
if (xemaclite_mdio_wait(lp))
return -ETIMEDOUT;
- rc = __raw_readl(lp->base_addr + XEL_MDIORD_OFFSET);
+ rc = xemaclite_readl(lp->base_addr + XEL_MDIORD_OFFSET);
dev_dbg(&lp->ndev->dev,
"xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
@@ -783,13 +791,13 @@ static int xemaclite_mdio_write(struct m
* Data register. Finally, set the Status bit in the MDIO Control
* register to start a MDIO write transaction.
*/
- ctrl_reg = __raw_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET);
- __raw_writel(~XEL_MDIOADDR_OP_MASK &
- ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg),
- lp->base_addr + XEL_MDIOADDR_OFFSET);
- __raw_writel(val, lp->base_addr + XEL_MDIOWR_OFFSET);
- __raw_writel(ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK,
- lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ ctrl_reg = xemaclite_readl(lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ xemaclite_writel(~XEL_MDIOADDR_OP_MASK &
+ ((phy_id << XEL_MDIOADDR_PHYADR_SHIFT) | reg),
+ lp->base_addr + XEL_MDIOADDR_OFFSET);
+ xemaclite_writel(val, lp->base_addr + XEL_MDIOWR_OFFSET);
+ xemaclite_writel(ctrl_reg | XEL_MDIOCTRL_MDIOSTS_MASK,
+ lp->base_addr + XEL_MDIOCTRL_OFFSET);
return 0;
}
@@ -834,8 +842,8 @@ static int xemaclite_mdio_setup(struct n
/* Enable the MDIO bus by asserting the enable bit in MDIO Control
* register.
*/
- __raw_writel(XEL_MDIOCTRL_MDIOEN_MASK,
- lp->base_addr + XEL_MDIOCTRL_OFFSET);
+ xemaclite_writel(XEL_MDIOCTRL_MDIOEN_MASK,
+ lp->base_addr + XEL_MDIOCTRL_OFFSET);
bus = mdiobus_alloc();
if (!bus) {
@@ -1138,8 +1146,8 @@ static int xemaclite_of_probe(struct pla
dev_warn(dev, "No MAC address found\n");
/* Clear the Tx CSR's in case this is a restart */
- __raw_writel(0, lp->base_addr + XEL_TSR_OFFSET);
- __raw_writel(0, lp->base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET);
+ xemaclite_writel(0, lp->base_addr + XEL_TSR_OFFSET);
+ xemaclite_writel(0, lp->base_addr + XEL_BUFFER_OFFSET + XEL_TSR_OFFSET);
/* Set the MAC address in the EmacLite device */
xemaclite_update_address(lp, ndev->dev_addr);
Powered by blists - more mailing lists