linux-kernel - [PATCH 1/2] dt-bindings: spi: Document the STM32 SPI bindings

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1498055526-6918-2-git-send-email-amelie.delaunay@st.com>
Date:   Wed, 21 Jun 2017 16:32:05 +0200
From:   Amelie Delaunay <amelie.delaunay@...com>
To:     Mark Brown <broonie@...nel.org>, Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Maxime Coquelin <mcoquelin.stm32@...il.com>,
        Alexandre Torgue <alexandre.torgue@...com>
CC:     <linux-spi@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>,
        Amelie Delaunay <amelie.delaunay@...com>
Subject: [PATCH 1/2] dt-bindings: spi: Document the STM32 SPI bindings

This patch adds the documentation of device tree bindings
for the STM32 SPI controller.

Signed-off-by: Amelie Delaunay <amelie.delaunay@...com>
---
 .../devicetree/bindings/spi/spi-stm32.txt          | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt

diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt
new file mode 100644
index 0000000..3958bf6
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt
@@ -0,0 +1,60 @@
+STMicroelectronics STM32 SPI Controller
+
+The STM32 SPI controller is used to communicate with external devices using
+the Serial Peripheral Interface. It supports full-duplex, half-duplex and
+simplex synchronous serial communication with external devices. It supports
+from 4 to 32-bit data size. Although it can be configured as master or slave,
+only master is supported by the driver.
+
+Required properties:
+- compatible: Must be "st,stm32-spi".
+- reg: Offset and length of the device's register set.
+- interrupts: Must contain the interrupt id.
+- clocks: Must contain an entry for spiclk (which feeds the internal clock
+	  generator).
+- #address-cells:  Number of cells required to define a chip select address.
+- #size-cells: Should be zero.
+
+Optional properties:
+- resets: Must contain the phandle to the reset controller.
+- A pinctrl state named "default" may be defined to set pins in mode of
+  operation for SPI transfer.
+- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
+  STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
+- dma-names: DMA request names should include "tx" and "rx" if present.
+- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
+  Documentation/devicetree/bindings/spi/spi-bus.txt
+
+
+Child nodes represent devices on the SPI bus
+  See ../spi/spi-bus.txt
+
+Optional properties:
+- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
+		  nanoseconds inserted between two consecutive data frames.
+
+
+Example:
+	spi2: spi@...03800 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "st,stm32-spi";
+		reg = <0x40003800 0x400>;
+		interrupts = <36>;
+		clocks = <&rcc SPI2_CK>;
+		resets = <&rcc 1166>;
+		dmas = <&dmamux1 0 39 0x400 0x01>,
+		       <&dmamux1 1 40 0x400 0x01>;
+		dma-names = "rx", "tx";
+		pinctrl-0 = <&spi2_pins_b>;
+		pinctrl-names = "default";
+		status = "okay";
+		cs-gpios = <&gpioa 11 0>;
+
+		spidev@0 {
+			compatible = "spidev";
+			reg = <0>;
+			spi-max-frequency = <4000000>;
+			st,spi-midi = <4000>;
+		};
+	};
-- 
1.9.1