| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <247dcb9e-632a-b0c3-0ce0-fce55ab4cd0c@denx.de>
Date: Fri, 6 Oct 2017 22:50:56 +0200
From: Łukasz Majewski <lukma@...x.de>
To: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Russell King <linux@...linux.org.uk>,
Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <kernel@...gutronix.de>,
Fabio Estevam <fabio.estevam@....com>,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org
Cc: festevam@...il.com
Subject: Re: [PATCH v2] dts: display5: Device tree description of LWN's
DISPLAY5 board
Dear All,
> This commit adds device tree description of Liebherr's Display5 board.
Gentle ping on this patch.....
Best regards,
Łukasz
>
> Signed-off-by: Lukasz Majewski <lukma@...x.de>
>
> ---
> Changes for v2:
>
> - Postpone adding Mitsubishi display
> - Replace GPL with dual GPL/X11 licenses
> - Remove superfluous "i2s-master" property
> - Replace pinctrl 0x80000000 value (meaning that this ping shall not be
> configured in Linux) with proper values (set by bootloader)
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/imx6q-display5-tianma-tm070-1280x768.dts | 51 ++
> arch/arm/boot/dts/imx6q-display5.dtsi | 582 +++++++++++++++++++++
> 3 files changed, 634 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
> create mode 100644 arch/arm/boot/dts/imx6q-display5.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4b17f35..c1648f0 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -400,6 +400,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cm-fx6.dtb \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> + imx6q-display5-tianma-tm070-1280x768.dtb \
> imx6q-dmo-edmqmx6.dtb \
> imx6q-evi.dtb \
> imx6q-gk802.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
> new file mode 100644
> index 0000000..16658b7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
> @@ -0,0 +1,51 @@
> +/*
> + * Copyright 2017
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without
> + * any warranty of any kind, whether express or implied.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q-display5.dtsi"
> +
> +&panel {
> + compatible = "tianma,tm070jdhg30";
> +};
> +
> +&ldb {
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/imx6q-display5.dtsi
> new file mode 100644
> index 0000000..a7d9144
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-display5.dtsi
> @@ -0,0 +1,582 @@
> +/*
> + * Copyright 2017
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without
> + * any warranty of any kind, whether express or implied.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + model = "Liebherr (LWN) display5 i.MX6 Quad Board";
> + compatible = "lwn,display5", "fsl,imx6q";
> +
> + memory {
> + reg = <0x10000000 0x40000000>;
> + };
> +
> + backlight_lvds: backlight {
> + compatible = "pwm-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + pwms = <&pwm2 0 5000000 0>;
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100 101 102 103 104 105 106 107 108 109
> + 110 111 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127 128 129
> + 130 131 132 133 134 135 136 137 138 139
> + 140 141 142 143 144 145 146 147 148 149
> + 150 151 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167 168 169
> + 170 171 172 173 174 175 176 177 178 179
> + 180 181 182 183 184 185 186 187 188 189
> + 190 191 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207 208 209
> + 210 211 212 213 214 215 216 217 218 219
> + 220 221 222 223 224 225 226 227 228 229
> + 230 231 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247 248 249
> + 250 251 252 253 254 255>;
> + default-brightness-level = <250>;
> + enable-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_lvds: regulator-lvds {
> + compatible = "regulator-fixed";
> + regulator-name = "lvds_ppen";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_lvds>;
> + gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usbh1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_vbus>;
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + label = "tfa9879-mono";
> +
> + simple-audio-card,dai-link {
> + /* DAC */
> + format = "i2s";
> + bitclock-master = <&dailink_master>;
> + frame-master = <&dailink_master>;
> +
> + dailink_master: cpu {
> + sound-dai = <&ssi2>;
> + };
> + codec {
> + sound-dai = <&codec>;
> + };
> + };
> + };
> +
> + panel: panel-lvds0 {
> + backlight = <&backlight_lvds>;
> + power-supply = <®_lvds>;
> +
> + port {
> + panel_in_lvds0: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + ssi2 {
> + fsl,audmux-port = <1>;
> + fsl,port-config = <
> + (IMX_AUDMUX_V2_PTCR_SYN |
> + IMX_AUDMUX_V2_PTCR_TFSEL(5) |
> + IMX_AUDMUX_V2_PTCR_TCSEL(5) |
> + IMX_AUDMUX_V2_PTCR_TFSDIR |
> + IMX_AUDMUX_V2_PTCR_TCLKDIR)
> + IMX_AUDMUX_V2_PDCR_RXDSEL(5)
> + >;
> + };
> +
> + aud6 {
> + fsl,audmux-port = <5>;
> + fsl,port-config = <
> + (IMX_AUDMUX_V2_PTCR_RFSEL(8) |
> + IMX_AUDMUX_V2_PTCR_RCSEL(8) |
> + IMX_AUDMUX_V2_PTCR_TFSEL(1) |
> + IMX_AUDMUX_V2_PTCR_TCSEL(1) |
> + IMX_AUDMUX_V2_PTCR_RFSDIR |
> + IMX_AUDMUX_V2_PTCR_RCLKDIR |
> + IMX_AUDMUX_V2_PTCR_TFSDIR |
> + IMX_AUDMUX_V2_PTCR_TCLKDIR)
> + IMX_AUDMUX_V2_PDCR_RXDSEL(1)
> + >;
> + };
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs &pinctrl_ecspi2_flwp>;
> + status = "okay";
> +
> + s25fl256s: flash@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <40000000>;
> + reg = <0>;
> +
> + partition@0 {
> + label = "SPL (spi)";
> + reg = <0x0 0x20000>;
> + read-only;
> + };
> + partition@1 {
> + label = "u-boot (spi)";
> + reg = <0x20000 0x100000>;
> + read-only;
> + };
> + partition@2 {
> + label = "uboot-env (spi)";
> + reg = <0x120000 0x10000>;
> + };
> + partition@3 {
> + label = "uboot-envr (spi)";
> + reg = <0x130000 0x10000>;
> + };
> + partition@4 {
> + label = "linux-recovery (spi)";
> + reg = <0x140000 0x800000>;
> + };
> + partition@5 {
> + label = "swupdate-fitImg (spi)";
> + reg = <0x940000 0x400000>;
> + };
> + partition@6 {
> + label = "swupdate-initramfs (spi)";
> + reg = <0xD40000 0x800000>;
> + };
> + };
> +};
> +
> +&ecspi3 {
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + codec: tfa9879@6C {
> + #sound-dai-cells = <0>;
> + compatible = "tfa9879";
> + reg = <0x6C>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + at24@50 {
> + compatible = "at24,24c256";
> + pagesize = <64>;
> + reg = <0x50>;
> + };
> +
> + pfuze100: pmic@08 {
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in_lvds0>;
> + };
> + };
> + };
> +};
> +
> +&pwm2 {
> + #pwm-cells = <3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "okay";
> +};
> +
> +&ssi2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usbh1_vbus>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> +
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + /* I2S OUTPUT AUD6*/
> + MX6QDL_PAD_DI0_PIN4__AUD6_RXD 0x130b0
> + MX6QDL_PAD_DI0_PIN2__AUD6_TXD 0x130b0
> + MX6QDL_PAD_DI0_PIN3__AUD6_TXFS 0x130b0
> + MX6QDL_PAD_DI0_PIN15__AUD6_TXC 0x130b0
> + >;
> + };
> +
> + pinctrl_backlight: dispgrp {
> + fsl,pins = <
> + /* BLEN_OUT */
> + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1
> + >;
> + };
> +
> + pinctrl_ecspi2_cs: ecspi2csgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x100b1
> + >;
> + };
> +
> + pinctrl_ecspi2_flwp: ecspi2flwpgrp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ecspi3: ecspi3grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> + >;
> + };
> +
> + pinctrl_ecspi3_cs: ecspi3csgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ecspi3_flwp: ecspi3flwpgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
> + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_pwm2: pwm2grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_reg_lvds: reqlvdsgrp {
> + fsl,pins = <
> + /* LVDS_PPEN_OUT */
> + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbh1_vbus: usbh1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D31__USB_H1_PWR 0x130b0
> + MX6QDL_PAD_EIM_D30__USB_H1_OC 0x030b0
> + >;
> + };
> +
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x17059
> + >;
> + };
> +};
>
--
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@...x.de
Powered by blists - more mailing lists