| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1508769290-2646-4-git-send-email-pure.logic@nexus-software.ie>
Date: Mon, 23 Oct 2017 15:34:46 +0100
From: Bryan O'Donoghue <pure.logic@...us-software.ie>
To: p.zabel@...gutronix.de, richard.leitner@...data.com,
srinivas.kandagatla@...aro.org, axel.lin@...ics.com,
ping.bai@....com, d.schultz@...tec.de, peng.fan@....com,
van.freenix@...il.com
Cc: linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
pure.logic@...us-software.ie
Subject: [PATCH v4 3/7] nvmem: imx-ocotp: Add support for banked OTP addressing
The i.MX7S/D takes the bank address in the CTRLn.ADDR field and the data
value in one of the DATAx {0, 1, 2, 3} register fields. The current write
routine is based on writing the CTRLn.ADDR field and writing a single DATA
register only.
Fixes: 0642bac7da42 ("nvmem: imx-ocotp: add write support")
Signed-off-by: Bryan O'Donoghue <pure.logic@...us-software.ie>
Reviewed-by: Philipp Zabel <p.zabel@...gutronix.de>
---
drivers/nvmem/imx-ocotp.c | 68 ++++++++++++++++++++++++++++++++++++++++++++---
1 file changed, 64 insertions(+), 4 deletions(-)
diff --git a/drivers/nvmem/imx-ocotp.c b/drivers/nvmem/imx-ocotp.c
index b035e47..e10a0da 100644
--- a/drivers/nvmem/imx-ocotp.c
+++ b/drivers/nvmem/imx-ocotp.c
@@ -40,7 +40,10 @@
#define IMX_OCOTP_ADDR_CTRL_SET 0x0004
#define IMX_OCOTP_ADDR_CTRL_CLR 0x0008
#define IMX_OCOTP_ADDR_TIMING 0x0010
-#define IMX_OCOTP_ADDR_DATA 0x0020
+#define IMX_OCOTP_ADDR_DATA0 0x0020
+#define IMX_OCOTP_ADDR_DATA1 0x0030
+#define IMX_OCOTP_ADDR_DATA2 0x0040
+#define IMX_OCOTP_ADDR_DATA3 0x0050
#define IMX_OCOTP_BM_CTRL_ADDR 0x0000007F
#define IMX_OCOTP_BM_CTRL_BUSY 0x00000100
@@ -55,6 +58,7 @@ static DEFINE_MUTEX(ocotp_mutex);
struct ocotp_params {
unsigned int nregs;
+ unsigned int bank_address_words;
};
struct ocotp_priv {
@@ -176,6 +180,7 @@ static int imx_ocotp_write(void *context, unsigned int offset, void *val,
u32 timing = 0;
u32 ctrl;
u8 waddr;
+ u8 word = 0;
/* allow only writing one complete OTP word at a time */
if ((bytes != priv->config->word_size) ||
@@ -228,8 +233,23 @@ static int imx_ocotp_write(void *context, unsigned int offset, void *val,
* description. Both the unlock code and address can be written in the
* same operation.
*/
- /* OTP write/read address specifies one of 128 word address locations */
- waddr = offset / 4;
+ if (priv->params->bank_address_words != 0) {
+ /*
+ * In banked/i.MX7 mode the OTP register bank goes into waddr
+ * see i.MX 7Solo Applications Processor Reference Manual, Rev.
+ * 0.1 section 6.4.3.1
+ */
+ offset = offset / priv->config->word_size;
+ waddr = offset / priv->params->bank_address_words;
+ word = offset & (priv->params->bank_address_words - 1);
+ } else {
+ /*
+ * Non-banked i.MX6 mode.
+ * OTP write/read address specifies one of 128 word address
+ * locations
+ */
+ waddr = offset / 4;
+ }
ctrl = readl(priv->base + IMX_OCOTP_ADDR_CTRL);
ctrl &= ~IMX_OCOTP_BM_CTRL_ADDR;
@@ -255,8 +275,43 @@ static int imx_ocotp_write(void *context, unsigned int offset, void *val,
* shift right (with zero fill). This shifting is required to program
* the OTP serially. During the write operation, HW_OCOTP_DATA cannot be
* modified.
+ * Note: on i.MX7 there are four data fields to write for banked write
+ * with the fuse blowing operation only taking place after data0
+ * has been written. This is why data0 must always be the last
+ * register written.
*/
- writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA);
+ if (priv->params->bank_address_words != 0) {
+ /* Banked/i.MX7 mode */
+ switch (word) {
+ case 0:
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
+ writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0);
+ break;
+ case 1:
+ writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA1);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
+ break;
+ case 2:
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
+ writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA2);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
+ break;
+ case 3:
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
+ writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA3);
+ writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
+ break;
+ }
+ } else {
+ /* Non-banked i.MX6 mode */
+ writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0);
+ }
/* 47.4.1.4.5
* Once complete, the controller will clear BUSY. A write request to a
@@ -314,22 +369,27 @@ static struct nvmem_config imx_ocotp_nvmem_config = {
static const struct ocotp_params imx6q_params = {
.nregs = 128,
+ .bank_address_words = 0,
};
static const struct ocotp_params imx6sl_params = {
.nregs = 64,
+ .bank_address_words = 0,
};
static const struct ocotp_params imx6sx_params = {
.nregs = 128,
+ .bank_address_words = 0,
};
static const struct ocotp_params imx6ul_params = {
.nregs = 128,
+ .bank_address_words = 0,
};
static const struct ocotp_params imx7d_params = {
.nregs = 64,
+ .bank_address_words = 4,
};
static const struct of_device_id imx_ocotp_dt_ids[] = {
--
2.7.4
Powered by blists - more mailing lists