linux-kernel - Re: [linux-sunxi] Re: [PATCH] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Message-ID: <20171113082059.cxi7diuy6dvremlo@flea.lan>
Date:   Mon, 13 Nov 2017 09:20:59 +0100
From:   Maxime Ripard <maxime.ripard@...e-electrons.com>
To:     Icenowy Zheng <icenowy@...c.io>
Cc:     Chen-Yu Tsai <wens@...e.org>, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        linux-sunxi@...glegroups.com
Subject: Re: [linux-sunxi] Re: [PATCH] ARM: sun8i: h2+: add support for
 Banana Pi M2 Zero board

Hi,

On Fri, Nov 03, 2017 at 07:53:17AM +0800, Icenowy Zheng wrote:
> 在 2017-11-02 23:50，Maxime Ripard 写道：
> > On Thu, Nov 02, 2017 at 05:07:30PM +0800, Icenowy Zheng wrote:
> > > > > +&mmc0 {
> > > > > +	pinctrl-names = "default";
> > > > > +	pinctrl-0 = <&mmc0_pins_a>;
> > > > > +	vmmc-supply = <&reg_vcc3v3>;
> > > > > +	bus-width = <4>;
> > > > > +	/*
> > > > > +	 * In different revisions the board have different card detect
> > > > > +	 * configuration.
> > > > > +	 */
> > > >
> > > > Which ones?
> > > 
> > > In the sample batch (1.2V fixed voltage) the card detect is normal
> > > (PF6 low as inserted), however in the final batch (1.1V/1.3V
> > > switchable) it's inverted at PF6 (high as inserted).
> > 
> > Then just use the final version's.
> > 
> > > > > +&usbphy {
> > > > > +	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> > > > > +	/* USB OTG VBUS is directly connected to 5V without any regulators
> > > > > */
> > > >
> > > > So it cannot operate in OTG, but it's host only?
> > > 
> > > It can operate in OTG -- you can power the board via the OTG port,
> > > as the VBUS is not gated from 5V at all, so 5V power at VBUS will
> > > power up the board. Yes, it's a bit unsafe, but the board designer
> > > did it.
> > 
> > What will provide the 5v in the first place then if a USB device is
> > connected to the micro-USB connector?
> 
> There're two micro-USB connectors, one is power-only and another is
> OTG. The Vbus of these two connectors are connected together, so
> the external USB device will be powered just by the power input
> from the power-only USB port.

Can you put that in the comment?

Thanks.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Download attachment "signature.asc" of type "application/pgp-signature" (802 bytes)