| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20171130004342.GC22908@dragon>
Date: Thu, 30 Nov 2017 08:43:43 +0800
From: Shawn Guo <shawnguo@...nel.org>
To: Neil Armstrong <narmstrong@...libre.com>
Cc: kernel@...gutronix.de, fabio.estevam@....com,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v4 5/6] ARM: dts: imx6q: Add Variscite DART-MX6
Carrier-board support
On Wed, Nov 29, 2017 at 11:20:56AM +0100, Neil Armstrong wrote:
> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
> SoM Carrier-Board.
>
> This Carrier-Board has the following :
> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
> - HDMI Connector
> - USB Host + USB OTG Connector
> - 10/100/1000 Mbps Ethernet
> - miniPCI-Express slot
> - SD Card connector
> - Audio Headphone/Line In jack connectors
> - On-board DMIC
> - CAN bus header
> - SPI header
> - Camera Interfaces header
> - 4xButtons, 2xLeds
> - OnBoard RTC with Coin Backup battery socket
> - RS232 Header + USB-Serial debug port
>
> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
>
> The board support is done with all on-board and header interfaces enabled.
> 7" LVDS Touchscreen is enabled by default along HDMI output.
> Audio interface is supported with the "simple-card" bindings.
>
> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
>
> Reviewed-by: Fabio Estevam <fabio.estevam@....com>
> Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 239 +++++++++++++++++++++++++
> 2 files changed, 240 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d0381e9..148ff15 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-11x0-mb7.dtb \
> imx6q-udoo.dtb \
> imx6q-utilite-pro.dtb \
> + imx6q-var-dt6customboard.dtb \
> imx6q-wandboard.dtb \
> imx6q-wandboard-revb1.dtb \
> imx6q-wandboard-revd1.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> new file mode 100644
> index 0000000..76faaff
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> @@ -0,0 +1,239 @@
> +/*
> + * Support for Variscite DART-MX6 Carrier-board
> + *
> + * Copyright 2017 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@...libre.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-var-dart.dtsi"
> +#include <dt-bindings/input/linux-event-codes.h>
> +
> +/ {
> + model = "Variscite DART-MX6 Carrier-board";
> + compatible = "variscite,dt6customboard", "fsl,imx6q";
> +
> + backlight_lvds: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 50000>;
> + brightness-levels = <0 4 8 16 32 64 128 248>;
> + default-brightness-level = <7>;
> + status = "okay";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + back {
> + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_BACK>;
> + label = "Key Back";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
The gpio-key,wakeup is legacy one. Use wakeup-source instead.
> + };
> +
> + home {
> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOME>;
> + label = "Key Home";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> +
> + menu {
> + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_MENU>;
> + label = "Key Menu";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + led1 {
> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led2 {
> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + panel1: lvds-panel {
> + compatible = "sgd,gktw70sdae4se", "panel-lvds";
> + backlight = <&backlight_lvds>;
> +
> + width-mm = <153>;
> + height-mm = <86>;
> +
> + label = "gktw70sdae4se";
> +
Nit: these lines in middle of property list is not really necessary.
Can we drop them?
Shawn
> + data-mapping = "jeida-18";
> +
> + panel-timing {
> + clock-frequency = <32000000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <39>;
> + hfront-porch = <39>;
> + vback-porch = <29>;
> + vfront-porch = <13>;
> + hsync-len = <47>;
> + vsync-len = <2>;
> + };
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds1_out>;
> + };
> + };
> + };
> +
> + reg_usb_h1_vbus: regulator-usbh1vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_otg_vbus: regulator-usbotgvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "dt6-customboard-audio";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,bitclock-master = <&sound_codec>;
> + simple-audio-card,frame-master = <&sound_codec>;
> + simple-audio-card,widgets = "Headphone", "Headphone Jack",
> + "Line", "Line In";
> + simple-audio-card,routing = "Headphone Jack", "HPLOUT",
> + "Headphone Jack", "HPROUT",
> + "LINE1L", "Line In",
> + "LINE1R", "Line In";
> +
> + sound_cpu: simple-audio-card,cpu {
> + sound-dai = <&ssi2>;
> + };
> +
> + sound_codec: simple-audio-card,codec {
> + sound-dai = <&codec>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + };
> + };
> +};
> +
> +&can1 {
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
> + <&gpio4 10 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&fec {
> + status = "okay";
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + touchscreen@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> + touchscreen-size-x = <800>;
> + touchscreen-size-y = <480>;
> + touchscreen-inverted-x;
> + touchscreen-inverted-y;
> + };
> +
> + rtc@68 {
> + compatible = "isil,isl12057";
> + reg = <0x68>;
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@1 {
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds1_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&pwm2 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + dr_mode = "otg";
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> --
> 2.7.4
>
Powered by blists - more mailing lists