linux-kernel - [PATCH v4 3/4] arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1512383692-14009-4-git-send-email-geert+renesas@glider.be>
Date:   Mon,  4 Dec 2017 11:34:51 +0100
From:   Geert Uytterhoeven <geert+renesas@...der.be>
To:     "David S . Miller" <davem@...emloft.net>,
        Andrew Lunn <andrew@...n.ch>,
        Florian Fainelli <f.fainelli@...il.com>,
        Simon Horman <horms@...ge.net.au>,
        Magnus Damm <magnus.damm@...il.com>
Cc:     Sergei Shtylyov <sergei.shtylyov@...entembedded.com>,
        Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Nicolas Ferre <nicolas.ferre@...rochip.com>,
        Richard Leitner <richard.leitner@...data.com>,
        netdev@...r.kernel.org, devicetree@...r.kernel.org,
        linux-renesas-soc@...r.kernel.org, linux-kernel@...r.kernel.org,
        Geert Uytterhoeven <geert+renesas@...der.be>
Subject: [PATCH v4 3/4] arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset

Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.

This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.

On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.

Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.

Signed-off-by: Geert Uytterhoeven <geert+renesas@...der.be>
---
For proper PHY reset operation during system resume, this depends on
"[PATCH v4 1/4] phylib: Add device reset GPIO support".
However, this patch can be applied independently.

v4:
  - No changes,

v3:
  - Extract from series "[PATCH 0/4] ravb: Add PHY reset support", and
    incorporate in this series,
  - Move reset-gpios from the ethernet to the ethernet-phy node.
---
 arch/arm64/boot/dts/renesas/salvator-common.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index a298df74ca6c037f..6a9524ff881306cf 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -264,6 +264,7 @@
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 	};
 };
 
-- 
2.7.4