Message-ID: <20171205022903.GB20321@leoy-linaro>
Date:   Tue, 5 Dec 2017 10:29:03 +0800
From:   Leo Yan <leo.yan@...aro.org>
To:     Xu YiPing <xuyiping@...ilicon.com>
Cc:     robh+dt@...nel.org, mark.rutland@....com, xuwei5@...ilicon.com,
        catalin.marinas@....com, will.deacon@....com,
        jassisinghbrar@...il.com, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
        guodong.xu@...aro.org, haojian.zhuang@...aro.org,
        suzhuangluan@...ilicon.com, xuezhiliang@...ilicon.com,
        kevin.wangtao@...ilicon.com, zhongkaihua@...wei.com
Subject: Re: [PATCH v3 2/3] mailbox: Add support for Hi3660 mailbox

On Fri, Nov 17, 2017 at 05:24:31PM +0800, Xu YiPing wrote:
> From: Kaihua Zhong <zhongkaihua@...wei.com>
> 
> Hi3660 mailbox controller is used to send message within multiple
> processors, MCU, HIFI, etc.  It supports 32 mailbox channels and every
> channel can only be used for single transferring direction.  Once the
> channel is enabled, it needs to specify the destination interrupt and
> acknowledge interrupt, these two interrupt vectors are used to create
> the connection between the mailbox and interrupt controllers.
> 
> The data transferring supports two modes, one is named as "automatic
> acknowledge" mode so after send message the kernel doesn't need to wait
> for acknowledge from remote and directly return; there have another mode
> is to rely on handling interrupt for acknowledge.
> 
> This commit is for initial version driver, which only supports
> "automatic acknowledge" mode to support CPU clock, which is the only
> one consumer to use mailbox and has been verified.  Later may enhance
> this driver for interrupt mode (e.g. for supporting HIFI).

Gentle ping ...

> Signed-off-by: Leo Yan <leo.yan@...aro.org>
> Signed-off-by: Ruyi Wang <wangruyi@...wei.com>
> Signed-off-by: Kaihua Zhong <zhongkaihua@...wei.com>
> ---
>  drivers/mailbox/Kconfig          |   8 +
>  drivers/mailbox/Makefile         |   2 +
>  drivers/mailbox/hi3660-mailbox.c | 322 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 332 insertions(+)
>  create mode 100644 drivers/mailbox/hi3660-mailbox.c
> 
> diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
> index c5731e5..4b5d6e9 100644
> --- a/drivers/mailbox/Kconfig
> +++ b/drivers/mailbox/Kconfig
> @@ -108,6 +108,14 @@ config TI_MESSAGE_MANAGER
>  	  multiple processors within the SoC. Select this driver if your
>  	  platform has support for the hardware block.
>  
> +config HI3660_MBOX
> +	tristate "Hi3660 Mailbox"
> +	depends on ARCH_HISI && OF
> +	help
> +	  An implementation of the hi3660 mailbox. It is used to send message
> +	  between application processors and other processors/MCU/DSP. Select
> +	  Y here if you want to use Hi3660 mailbox controller.
> +
>  config HI6220_MBOX
>  	tristate "Hi6220 Mailbox"
>  	depends on ARCH_HISI
> diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
> index d54e412..7d1bd51 100644
> --- a/drivers/mailbox/Makefile
> +++ b/drivers/mailbox/Makefile
> @@ -26,6 +26,8 @@ obj-$(CONFIG_TI_MESSAGE_MANAGER) += ti-msgmgr.o
>  
>  obj-$(CONFIG_XGENE_SLIMPRO_MBOX) += mailbox-xgene-slimpro.o
>  
> +obj-$(CONFIG_HI3660_MBOX)	+= hi3660-mailbox.o
> +
>  obj-$(CONFIG_HI6220_MBOX)	+= hi6220-mailbox.o
>  
>  obj-$(CONFIG_BCM_PDC_MBOX)	+= bcm-pdc-mailbox.o
> diff --git a/drivers/mailbox/hi3660-mailbox.c b/drivers/mailbox/hi3660-mailbox.c
> new file mode 100644
> index 0000000..ba80834
> --- /dev/null
> +++ b/drivers/mailbox/hi3660-mailbox.c
> @@ -0,0 +1,322 @@
> +/*
> + * Hisilicon's Hi3660 mailbox controller driver
> + *
> + * Copyright (c) 2017 Hisilicon Limited.
> + * Copyright (c) 2017 Linaro Limited.
> + *
> + * Author: Leo Yan <leo.yan@...aro.org>
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation, version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mailbox_controller.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +#include "mailbox.h"
> +
> +#define MBOX_CHAN_MAX			32
> +
> +#define MBOX_RX				(0x0)
> +#define MBOX_TX				(0x1)
> +
> +#define MBOX_BASE(mbox, ch)		((mbox)->base + ((ch) * 0x40))
> +#define MBOX_SRC_REG			(0x00)
> +#define MBOX_DST_REG			(0x04)
> +#define MBOX_DCLR_REG			(0x08)
> +#define MBOX_DSTAT_REG			(0x0c)
> +#define MBOX_MODE_REG			(0x10)
> +#define MBOX_IMASK_REG			(0x14)
> +#define MBOX_ICLR_REG			(0x18)
> +#define MBOX_SEND_REG			(0x1c)
> +#define MBOX_DATA_REG			(0x20)
> +
> +#define MBOX_IPC_LOCK_REG		(0xa00)
> +#define MBOX_IPC_UNLOCK			(0x1acce551)
> +
> +#define MBOX_AUTOMATIC_ACK		(1)
> +
> +#define MBOX_STATE_IDLE			BIT(4)
> +#define MBOX_STATE_ACK			BIT(7)
> +
> +#define MBOX_MSG_LEN			8
> +
> +/**
> + * Hi3660 mailbox channel device data
> + *
> + * A channel can be used for TX or RX, it can trigger remote
> + * processor interrupt to notify remote processor and can receive
> + * interrupt if has incoming message.
> + *
> + * @dst_irq:	Interrupt vector for remote processor
> + * @ack_irq:	Interrupt vector for local processor
> + */
> +struct hi3660_mbox_dev {
> +	unsigned int dst_irq;
> +	unsigned int ack_irq;
> +};
> +
> +/**
> + * Hi3660 mailbox controller data
> + *
> + * Mailbox controller includes 32 channels and can allocate
> + * channel for message transferring.
> + *
> + * @dev:	Device to which it is attached
> + * @base:	Base address of the register mapping region
> + * @chan:	Representation of channels in mailbox controller
> + * @mdev:	Representation of channel device data
> + * @controller:	Representation of a communication channel controller
> + */
> +struct hi3660_mbox {
> +	struct device *dev;
> +	void __iomem *base;
> +	struct mbox_chan chan[MBOX_CHAN_MAX];
> +	struct hi3660_mbox_dev mdev[MBOX_CHAN_MAX];
> +	struct mbox_controller controller;
> +};
> +
> +static inline struct hi3660_mbox *to_hi3660_mbox(struct mbox_controller *mbox)
> +{
> +	return container_of(mbox, struct hi3660_mbox, controller);
> +}
> +
> +static int hi3660_mbox_check_state(struct mbox_chan *chan)
> +{
> +	unsigned long ch = (unsigned long)chan->con_priv;
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +	struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +	void __iomem *base = MBOX_BASE(mbox, ch);
> +	unsigned long val;
> +	unsigned int state, ret;
> +
> +	/* Mailbox is idle so directly bail out */
> +	state = readl_relaxed(base + MBOX_MODE_REG);
> +	if (state & MBOX_STATE_IDLE)
> +		return 0;
> +
> +	/* Wait for acknowledge from remote */
> +	ret = readx_poll_timeout_atomic(readl_relaxed, base + MBOX_MODE_REG,
> +			val, (val & MBOX_STATE_ACK), 1000, 300000);
> +	if (ret) {
> +		dev_err(mbox->dev, "%s: timeout for receiving ack\n", __func__);
> +		return ret;
> +	}
> +
> +	/* Ensure channel is released */
> +	writel_relaxed(0xffffffff, base + MBOX_IMASK_REG);
> +	writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SRC_REG);
> +
> +	return 0;
> +}
> +
> +static int hi3660_mbox_unlock(struct mbox_chan *chan)
> +{
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +	unsigned int val, retry = 3;
> +
> +	do {
> +		writel_relaxed(MBOX_IPC_UNLOCK, mbox->base + MBOX_IPC_LOCK_REG);
> +
> +		val = readl_relaxed(mbox->base + MBOX_IPC_LOCK_REG);
> +		if (!val)
> +			break;
> +
> +		udelay(10);
> +	} while (retry--);
> +
> +	return (!val) ? 0 : -ETIMEDOUT;
> +}
> +
> +static int hi3660_mbox_acquire_channel(struct mbox_chan *chan)
> +{
> +	unsigned long ch = (unsigned long)chan->con_priv;
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +	struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +	void __iomem *base = MBOX_BASE(mbox, ch);
> +	unsigned int val, retry;
> +
> +	for (retry = 10; retry; retry--) {
> +		/* Check if channel has been acquired */
> +		if (readl_relaxed(base + MBOX_MODE_REG) & MBOX_STATE_IDLE) {
> +			writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SRC_REG);
> +			val = readl_relaxed(base + MBOX_SRC_REG);
> +			if (val & BIT(mdev->ack_irq))
> +				break;
> +		}
> +	}
> +
> +	return retry ? 0 : -ETIMEDOUT;
> +}
> +
> +static int hi3660_mbox_send(struct mbox_chan *chan, u32 *msg)
> +{
> +	unsigned long ch = (unsigned long)chan->con_priv;
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +	struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +	void __iomem *base = MBOX_BASE(mbox, ch);
> +	unsigned int i;
> +
> +	/* Clear mask for destination interrupt */
> +	writel_relaxed(~BIT(mdev->dst_irq), base + MBOX_IMASK_REG);
> +
> +	/* Config destination for interrupt vector */
> +	writel_relaxed(BIT(mdev->dst_irq), base + MBOX_DST_REG);
> +
> +	/* Automatic acknowledge mode */
> +	writel_relaxed(MBOX_AUTOMATIC_ACK, base + MBOX_MODE_REG);
> +
> +	/* Fill message data */
> +	for (i = 0; i < MBOX_MSG_LEN; i++)
> +		writel_relaxed(msg[i], base + MBOX_DATA_REG + i * 4);
> +
> +	/* Trigger data transferring */
> +	writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SEND_REG);
> +	return 0;
> +}
> +
> +static int hi3660_mbox_send_data(struct mbox_chan *chan, void *msg)
> +{
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +	int err;
> +
> +	err = hi3660_mbox_check_state(chan);
> +	if (err) {
> +		dev_err(mbox->dev, "checking state failed\n");
> +		return err;
> +	}
> +
> +	err = hi3660_mbox_unlock(chan);
> +	if (err) {
> +		dev_err(mbox->dev, "unlocking mailbox failed\n");
> +		return err;
> +	}
> +
> +	err = hi3660_mbox_acquire_channel(chan);
> +	if (err) {
> +		dev_err(mbox->dev, "acquiring channel failed\n");
> +		return err;
> +	}
> +
> +	return hi3660_mbox_send(chan, msg);
> +}
> +
> +static struct mbox_chan_ops hi3660_mbox_ops = {
> +	.send_data    = hi3660_mbox_send_data,
> +};
> +
> +static struct mbox_chan *hi3660_mbox_xlate(struct mbox_controller *controller,
> +					   const struct of_phandle_args *spec)
> +{
> +	struct hi3660_mbox *mbox = to_hi3660_mbox(controller);
> +	struct hi3660_mbox_dev *mdev;
> +	unsigned int ch = spec->args[0];
> +
> +	if (ch >= MBOX_CHAN_MAX) {
> +		dev_err(mbox->dev, "Invalid channel idx %d\n", ch);
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	mdev = &mbox->mdev[ch];
> +	mdev->dst_irq = spec->args[1];
> +	mdev->ack_irq = spec->args[2];
> +
> +	return &mbox->chan[ch];
> +}
> +
> +static const struct of_device_id hi3660_mbox_of_match[] = {
> +	{ .compatible = "hisilicon,hi3660-mbox", },
> +	{},
> +};
> +
> +MODULE_DEVICE_TABLE(of, hi3660_mbox_of_match);
> +
> +static int hi3660_mbox_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct hi3660_mbox *mbox;
> +	struct mbox_chan *chan;
> +	struct resource *res;
> +	unsigned long ch;
> +	int err;
> +
> +	mbox = devm_kzalloc(dev, sizeof(*mbox), GFP_KERNEL);
> +	if (!mbox)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	mbox->base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(mbox->base))
> +		return PTR_ERR(mbox->base);
> +
> +	mbox->dev = dev;
> +	mbox->controller.dev = dev;
> +	mbox->controller.chans = mbox->chan;
> +	mbox->controller.num_chans = MBOX_CHAN_MAX;
> +	mbox->controller.ops = &hi3660_mbox_ops;
> +	mbox->controller.of_xlate = hi3660_mbox_xlate;
> +
> +	/* Initialize mailbox channel data */
> +	chan = mbox->chan;
> +	for (ch = 0; ch < MBOX_CHAN_MAX; ch++)
> +		chan[ch].con_priv = (void *)ch;
> +
> +	err = mbox_controller_register(&mbox->controller);
> +	if (err) {
> +		dev_err(dev, "Failed to register mailbox %d\n", err);
> +		return err;
> +	}
> +
> +	platform_set_drvdata(pdev, mbox);
> +	dev_info(dev, "Mailbox enabled\n");
> +	return 0;
> +}
> +
> +static int hi3660_mbox_remove(struct platform_device *pdev)
> +{
> +	struct hi3660_mbox *mbox = platform_get_drvdata(pdev);
> +
> +	mbox_controller_unregister(&mbox->controller);
> +	return 0;
> +}
> +
> +static struct platform_driver hi3660_mbox_driver = {
> +	.probe  = hi3660_mbox_probe,
> +	.remove = hi3660_mbox_remove,
> +	.driver = {
> +		.name = "hi3660-mbox",
> +		.of_match_table = hi3660_mbox_of_match,
> +	},
> +};
> +
> +static int __init hi3660_mbox_init(void)
> +{
> +	return platform_driver_register(&hi3660_mbox_driver);
> +}
> +core_initcall(hi3660_mbox_init);
> +
> +static void __exit hi3660_mbox_exit(void)
> +{
> +	platform_driver_unregister(&hi3660_mbox_driver);
> +}
> +module_exit(hi3660_mbox_exit);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_DESCRIPTION("Hisilicon Hi3660 Mailbox Controller");
> +MODULE_AUTHOR("Leo Yan <leo.yan@...aro.org>");
> -- 
> 1.9.1
> 

Powered by blists - more mailing lists