linux-kernel - [PATCH 06/14] ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20171214134054.7749-7-kishon@ti.com>
Date:   Thu, 14 Dec 2017 19:10:46 +0530
From:   Kishon Vijay Abraham I <kishon@...com>
To:     Tony Lindgren <tony@...mide.com>, <bcousson@...libre.com>,
        Santosh Shilimkar <ssantosh@...nel.org>
CC:     Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Russell King <linux@...linux.org.uk>,
        <linux-mmc@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-kernel@...r.kernel.org>, <linux-omap@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>, <nsekhar@...com>,
        <kishon@...com>
Subject: [PATCH 06/14] ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes

From: Sekhar Nori <nsekhar@...com>

The SD card interface on DRA76x EVM can support
high speed SD cards. The eMMC onboard can support
upto HS200 mode.

Enable support for these higher speed modes in the
device-tree file.

Signed-off-by: Sekhar Nori <nsekhar@...com>
Signed-off-by: Kishon Vijay Abraham I <kishon@...com>
---
 arch/arm/boot/dts/dra76-evm.dts | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index 2770f6d3e1cb..ec8af5841061 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -313,16 +313,20 @@
 	 * is always hardwired.
 	 */
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
 };
 
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_hs>;
+	pinctrl-2 = <&mmc2_pins_ddr>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>;
 };
 
 /* No RTC on this device */
-- 
2.11.0