[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1516286070-24927-10-git-send-email-patrice.chotard@st.com>
Date: Thu, 18 Jan 2018 15:34:25 +0100
From: <patrice.chotard@...com>
To: Russell King <linux@...linux.org.uk>,
Ulf Hansson <ulf.hansson@...aro.org>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...eaurora.org>,
Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Alexandre Torgue <alexandre.torgue@...com>
CC: <linux-mmc@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-clk@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-gpio@...r.kernel.org>, <devicetree@...r.kernel.org>,
Andrea Merello <andrea.merello@...il.com>,
Patrice Chotard <patrice.chotard@...com>
Subject: [PATCH v3 09/14] ARM: dts: stm32: Enable SDIO controller on stm32f469 disco board
From: Andrea Merello <andrea.merello@...il.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@...il.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@...com>
Signed-off-by: Patrice Chotard <patrice.chotard@...com>
---
v3: _ none
v2: _ none
arch/arm/boot/dts/stm32f469-disco.dts | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index 318fb12..ebb97c3 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -66,6 +66,13 @@
serial0 = &usart3;
};
+ mmc_vcard: mmc_vcard {
+ compatible = "regulator-fixed";
+ regulator-name = "mmc_vcard";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
soc {
dma-ranges = <0xc0000000 0x0 0x10000000>;
};
@@ -120,6 +127,18 @@
};
};
+&sdio {
+ status = "okay";
+ vmmc-supply = <&mmc_vcard>;
+ cd-gpios = <&gpiog 2 0>;
+ cd-inverted;
+ broken-cd;
+ pinctrl-names = "default", "opendrain";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_pins_od>;
+ bus-width = <4>;
+};
+
&usart3 {
pinctrl-0 = <&usart3_pins_a>;
pinctrl-names = "default";
--
1.9.1
Powered by blists - more mailing lists