| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20180216170033.3834-2-mdf@kernel.org>
Date: Fri, 16 Feb 2018 09:00:33 -0800
From: Moritz Fischer <mdf@...nel.org>
To: linux-kernel@...r.kernel.org
Cc: devicetree@...r.kernel.org, netdev@...r.kernel.org,
robh+dt@...nel.org, mark.rutland@....com, andrew@...n.ch,
f.fainelli@...il.com, davem@...emloft.net,
Moritz Fischer <mdf@...nel.org>
Subject: [PATCH v3 2/2] net: ethernet: nixge: Add support for National Instruments XGE netdev
Add support for the National Instruments XGE 1/10G network device.
It uses the EEPROM on the board via NVMEM.
Signed-off-by: Moritz Fischer <mdf@...nel.org>
---
Changes from v2:
- Implement recv side NAPI
- Improved error handling
- Implemented C45 writes
- Added ethtool callbacks & blink functionality
- Improved nixge_ctrl_poll_timeout() macro
- Removed dev_dbg() for mdio accesses
- Added businfo to ethtool drvinfo
Changes from v1:
- Added dependency on ARCH_ZYNQ (Kbuild)
- Removed unused variables
- Use of_phy_connect as suggested
- Removed masking of (un)supported modes
- Added #define for some constants
- Removed empty pm functions
- Reworked mac_address handling
- Made nixge_mdio_*() static (sparse)
- Removed driver version
- Addressed timeout loop
- Adressed return values on timeout
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/ni/Kconfig | 27 +
drivers/net/ethernet/ni/Makefile | 1 +
drivers/net/ethernet/ni/nixge.c | 1352 ++++++++++++++++++++++++++++++++++++++
5 files changed, 1382 insertions(+)
create mode 100644 drivers/net/ethernet/ni/Kconfig
create mode 100644 drivers/net/ethernet/ni/Makefile
create mode 100644 drivers/net/ethernet/ni/nixge.c
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index b6cf4b6962f5..908218561fdd 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -129,6 +129,7 @@ config FEALNX
source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/netronome/Kconfig"
+source "drivers/net/ethernet/ni/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
config NET_NETX
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 3cdf01e96e0b..d732e9522b76 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_FEALNX) += fealnx.o
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
obj-$(CONFIG_NET_VENDOR_NETRONOME) += netronome/
+obj-$(CONFIG_NET_VENDOR_NI) += ni/
obj-$(CONFIG_NET_NETX) += netx-eth.o
obj-$(CONFIG_NET_VENDOR_NUVOTON) += nuvoton/
obj-$(CONFIG_NET_VENDOR_NVIDIA) += nvidia/
diff --git a/drivers/net/ethernet/ni/Kconfig b/drivers/net/ethernet/ni/Kconfig
new file mode 100644
index 000000000000..cd30f7de16de
--- /dev/null
+++ b/drivers/net/ethernet/ni/Kconfig
@@ -0,0 +1,27 @@
+#
+# National Instuments network device configuration
+#
+
+config NET_VENDOR_NI
+ bool "National Instruments Devices"
+ default y
+ ---help---
+ If you have a network (Ethernet) device belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about National Instrument devices.
+ If you say Y, you will be asked for your specific device in the
+ following questions.
+
+if NET_VENDOR_NI
+
+config NI_XGE_MANAGEMENT_ENET
+ tristate "National Instruments XGE management enet support"
+ depends on ARCH_ZYNQ
+ select PHYLIB
+ ---help---
+ Simple LAN device for debug or management purposes. Can
+ support either 10G or 1G PHYs via SFP+ ports.
+
+endif
diff --git a/drivers/net/ethernet/ni/Makefile b/drivers/net/ethernet/ni/Makefile
new file mode 100644
index 000000000000..99c664651c51
--- /dev/null
+++ b/drivers/net/ethernet/ni/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_NI_XGE_MANAGEMENT_ENET) += nixge.o
diff --git a/drivers/net/ethernet/ni/nixge.c b/drivers/net/ethernet/ni/nixge.c
new file mode 100644
index 000000000000..9b255c23d7cd
--- /dev/null
+++ b/drivers/net/ethernet/ni/nixge.c
@@ -0,0 +1,1352 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2016-2017, National Instruments Corp.
+ *
+ * Author: Moritz Fischer <mdf@...nel.org>
+ */
+
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_address.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/phy.h>
+#include <linux/mii.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/ethtool.h>
+#include <linux/if_vlan.h>
+#include <linux/iopoll.h>
+
+#define TX_BD_NUM 64
+#define RX_BD_NUM 128
+
+/* Axi DMA Register definitions */
+
+#define XAXIDMA_TX_CR_OFFSET 0x00000000 /* Channel control */
+#define XAXIDMA_TX_SR_OFFSET 0x00000004 /* Status */
+#define XAXIDMA_TX_CDESC_OFFSET 0x00000008 /* Current descriptor pointer */
+#define XAXIDMA_TX_TDESC_OFFSET 0x00000010 /* Tail descriptor pointer */
+
+#define XAXIDMA_RX_CR_OFFSET 0x00000030 /* Channel control */
+#define XAXIDMA_RX_SR_OFFSET 0x00000034 /* Status */
+#define XAXIDMA_RX_CDESC_OFFSET 0x00000038 /* Current descriptor pointer */
+#define XAXIDMA_RX_TDESC_OFFSET 0x00000040 /* Tail descriptor pointer */
+
+#define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */
+#define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */
+
+#define XAXIDMA_BD_NDESC_OFFSET 0x00 /* Next descriptor pointer */
+#define XAXIDMA_BD_BUFA_OFFSET 0x08 /* Buffer address */
+#define XAXIDMA_BD_CTRL_LEN_OFFSET 0x18 /* Control/buffer length */
+#define XAXIDMA_BD_STS_OFFSET 0x1C /* Status */
+#define XAXIDMA_BD_USR0_OFFSET 0x20 /* User IP specific word0 */
+#define XAXIDMA_BD_USR1_OFFSET 0x24 /* User IP specific word1 */
+#define XAXIDMA_BD_USR2_OFFSET 0x28 /* User IP specific word2 */
+#define XAXIDMA_BD_USR3_OFFSET 0x2C /* User IP specific word3 */
+#define XAXIDMA_BD_USR4_OFFSET 0x30 /* User IP specific word4 */
+#define XAXIDMA_BD_ID_OFFSET 0x34 /* Sw ID */
+#define XAXIDMA_BD_HAS_STSCNTRL_OFFSET 0x38 /* Whether has stscntrl strm */
+#define XAXIDMA_BD_HAS_DRE_OFFSET 0x3C /* Whether has DRE */
+
+#define XAXIDMA_BD_HAS_DRE_SHIFT 8 /* Whether has DRE shift */
+#define XAXIDMA_BD_HAS_DRE_MASK 0xF00 /* Whether has DRE mask */
+#define XAXIDMA_BD_WORDLEN_MASK 0xFF /* Whether has DRE mask */
+
+#define XAXIDMA_BD_CTRL_LENGTH_MASK 0x007FFFFF /* Requested len */
+#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK 0x0C000000 /* All control bits */
+
+#define XAXIDMA_DELAY_MASK 0xFF000000 /* Delay timeout counter */
+#define XAXIDMA_COALESCE_MASK 0x00FF0000 /* Coalesce counter */
+
+#define XAXIDMA_DELAY_SHIFT 24
+#define XAXIDMA_COALESCE_SHIFT 16
+
+#define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */
+#define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */
+#define XAXIDMA_IRQ_ERROR_MASK 0x00004000 /* Error interrupt */
+#define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */
+
+/* Default TX/RX Threshold and waitbound values for SGDMA mode */
+#define XAXIDMA_DFT_TX_THRESHOLD 24
+#define XAXIDMA_DFT_TX_WAITBOUND 254
+#define XAXIDMA_DFT_RX_THRESHOLD 24
+#define XAXIDMA_DFT_RX_WAITBOUND 254
+
+#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK 0x0C000000 /* All control bits */
+
+#define XAXIDMA_BD_STS_ACTUAL_LEN_MASK 0x007FFFFF /* Actual len */
+#define XAXIDMA_BD_STS_COMPLETE_MASK 0x80000000 /* Completed */
+#define XAXIDMA_BD_STS_DEC_ERR_MASK 0x40000000 /* Decode error */
+#define XAXIDMA_BD_STS_SLV_ERR_MASK 0x20000000 /* Slave error */
+#define XAXIDMA_BD_STS_INT_ERR_MASK 0x10000000 /* Internal err */
+#define XAXIDMA_BD_STS_ALL_ERR_MASK 0x70000000 /* All errors */
+#define XAXIDMA_BD_STS_RXSOF_MASK 0x08000000 /* First rx pkt */
+#define XAXIDMA_BD_STS_RXEOF_MASK 0x04000000 /* Last rx pkt */
+#define XAXIDMA_BD_STS_ALL_MASK 0xFC000000 /* All status bits */
+
+#define XAXIDMA_BD_MINIMUM_ALIGNMENT 0x40
+
+#define NIXGE_REG_CTRL_OFFSET 0x4000
+#define NIXGE_REG_INFO 0x00
+#define NIXGE_REG_MAC_CTL 0x04
+#define NIXGE_REG_PHY_CTL 0x08
+#define NIXGE_REG_LED_CTL 0x0c
+#define NIXGE_REG_MDIO_DATA 0x10
+#define NIXGE_REG_MDIO_ADDR 0x14
+#define NIXGE_REG_MDIO_OP 0x18
+#define NIXGE_REG_MDIO_CTRL 0x1c
+
+#define NIXGE_ID_LED_CTL_EN BIT(0)
+#define NIXGE_ID_LED_CTL_VAL BIT(1)
+
+#define NIXGE_MDIO_CLAUSE45 BIT(12)
+#define NIXGE_MDIO_CLAUSE22 0
+#define NIXGE_MDIO_OP(n) (((n) & 0x3) << 10)
+#define NIXGE_MDIO_OP_ADDRESS 0
+#define NIXGE_MDIO_OP_WRITE BIT(0)
+#define NIXGE_MDIO_OP_READ (BIT(1) | BIT(0))
+#define MDIO_C22_WRITE BIT(0)
+#define MDIO_C22_READ BIT(1)
+#define MDIO_READ_POST 2
+#define NIXGE_MDIO_ADDR(n) (((n) & 0x1f) << 5)
+#define NIXGE_MDIO_MMD(n) (((n) & 0x1f) << 0)
+
+#define NIXGE_MAX_PHY_ADDR 32
+
+#define NIXGE_REG_MAC_LSB 0x1000
+#define NIXGE_REG_MAC_MSB 0x1004
+
+/* Packet size info */
+#define NIXGE_HDR_SIZE 14 /* Size of Ethernet header */
+#define NIXGE_TRL_SIZE 4 /* Size of Ethernet trailer (FCS) */
+#define NIXGE_MTU 1500 /* Max MTU of an Ethernet frame */
+#define NIXGE_JUMBO_MTU 9000 /* Max MTU of a jumbo Eth. frame */
+
+#define NIXGE_MAX_FRAME_SIZE (NIXGE_MTU + NIXGE_HDR_SIZE + NIXGE_TRL_SIZE)
+#define NIXGE_MAX_JUMBO_FRAME_SIZE \
+ (NIXGE_JUMBO_MTU + NIXGE_HDR_SIZE + NIXGE_TRL_SIZE)
+
+struct nixge_hw_dma_bd {
+ u32 next; /* Physical address of next buffer descriptor */
+ u32 reserved1;
+ u32 phys;
+ u32 reserved2;
+ u32 reserved3;
+ u32 reserved4;
+ u32 cntrl;
+ u32 status;
+ u32 app0;
+ u32 app1; /* TX start << 16 | insert */
+ u32 app2;
+ u32 app3;
+ u32 app4;
+ u32 sw_id_offset;
+ u32 reserved5;
+ u32 reserved6;
+};
+
+struct nixge_tx_skb {
+ struct sk_buff *skb;
+ dma_addr_t mapping;
+ size_t size;
+ bool mapped_as_page;
+};
+
+struct nixge_priv {
+ struct net_device *ndev;
+ struct napi_struct napi;
+ struct device *dev;
+
+ /* Connection to PHY device */
+ struct device_node *phy_node;
+ phy_interface_t phy_mode;
+
+ int link;
+ unsigned int speed;
+ unsigned int duplex;
+
+ /* MDIO bus data */
+ struct mii_bus *mii_bus; /* MII bus reference */
+
+ /* IO registers, dma functions and IRQs */
+ void __iomem *ctrl_regs;
+ void __iomem *dma_regs;
+
+ struct tasklet_struct dma_err_tasklet;
+
+ int tx_irq;
+ int rx_irq;
+ u32 last_link;
+
+ /* Buffer descriptors */
+ struct nixge_hw_dma_bd *tx_bd_v;
+ struct nixge_tx_skb *tx_skb;
+ dma_addr_t tx_bd_p;
+
+ struct nixge_hw_dma_bd *rx_bd_v;
+ dma_addr_t rx_bd_p;
+ u32 tx_bd_ci;
+ u32 tx_bd_tail;
+ u32 rx_bd_ci;
+
+ u32 max_frm_size;
+
+ u32 coalesce_count_rx;
+ u32 coalesce_count_tx;
+};
+
+static void nixge_dma_write_reg(struct nixge_priv *priv, off_t offset, u32 val)
+{
+ writel(val, priv->dma_regs + offset);
+}
+
+static u32 nixge_dma_read_reg(const struct nixge_priv *priv, off_t offset)
+{
+ return readl(priv->dma_regs + offset);
+}
+
+static void nixge_ctrl_write_reg(struct nixge_priv *priv, off_t offset, u32 val)
+{
+ writel(val, priv->ctrl_regs + offset);
+}
+
+static u32 nixge_ctrl_read_reg(struct nixge_priv *priv, off_t offset)
+{
+ return readl(priv->ctrl_regs + offset);
+}
+
+#define nixge_ctrl_poll_timeout(priv, addr, val, cond, sleep_us, timeout_us) \
+ readl_poll_timeout((priv)->ctrl_regs + (addr), (val), (cond), \
+ (sleep_us), (timeout_us))
+
+#define nixge_dma_poll_timeout(priv, addr, val, cond, sleep_us, timeout_us) \
+ readl_poll_timeout((priv)->dma_regs + (addr), (val), (cond), \
+ (sleep_us), (timeout_us))
+
+static void nixge_hw_dma_bd_release(struct net_device *ndev)
+{
+ int i;
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ for (i = 0; i < RX_BD_NUM; i++) {
+ dma_unmap_single(ndev->dev.parent, priv->rx_bd_v[i].phys,
+ NIXGE_MAX_JUMBO_FRAME_SIZE, DMA_FROM_DEVICE);
+ dev_kfree_skb((struct sk_buff *)
+ (priv->rx_bd_v[i].sw_id_offset));
+ }
+
+ if (priv->rx_bd_v)
+ dma_free_coherent(ndev->dev.parent,
+ sizeof(*priv->rx_bd_v) * RX_BD_NUM,
+ priv->rx_bd_v,
+ priv->rx_bd_p);
+
+ if (priv->tx_skb)
+ devm_kfree(ndev->dev.parent, priv->tx_skb);
+
+ if (priv->tx_bd_v)
+ dma_free_coherent(ndev->dev.parent,
+ sizeof(*priv->tx_bd_v) * TX_BD_NUM,
+ priv->tx_bd_v,
+ priv->tx_bd_p);
+}
+
+static int nixge_hw_dma_bd_init(struct net_device *ndev)
+{
+ u32 cr;
+ int i;
+ struct sk_buff *skb;
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ /* Reset the indexes which are used for accessing the BDs */
+ priv->tx_bd_ci = 0;
+ priv->tx_bd_tail = 0;
+ priv->rx_bd_ci = 0;
+
+ /* Allocate the Tx and Rx buffer descriptors. */
+ priv->tx_bd_v = dma_zalloc_coherent(ndev->dev.parent,
+ sizeof(*priv->tx_bd_v) * TX_BD_NUM,
+ &priv->tx_bd_p, GFP_KERNEL);
+ if (!priv->tx_bd_v)
+ goto out;
+
+ priv->tx_skb = devm_kzalloc(ndev->dev.parent,
+ sizeof(*priv->tx_skb) *
+ TX_BD_NUM,
+ GFP_KERNEL);
+ if (!priv->tx_skb)
+ goto out;
+
+ priv->rx_bd_v = dma_zalloc_coherent(ndev->dev.parent,
+ sizeof(*priv->rx_bd_v) * RX_BD_NUM,
+ &priv->rx_bd_p, GFP_KERNEL);
+ if (!priv->rx_bd_v)
+ goto out;
+
+ for (i = 0; i < TX_BD_NUM; i++) {
+ priv->tx_bd_v[i].next = priv->tx_bd_p +
+ sizeof(*priv->tx_bd_v) *
+ ((i + 1) % TX_BD_NUM);
+ }
+
+ for (i = 0; i < RX_BD_NUM; i++) {
+ priv->rx_bd_v[i].next = priv->rx_bd_p +
+ sizeof(*priv->rx_bd_v) *
+ ((i + 1) % RX_BD_NUM);
+
+ skb = netdev_alloc_skb_ip_align(ndev,
+ NIXGE_MAX_JUMBO_FRAME_SIZE);
+ if (!skb)
+ goto out;
+
+ priv->rx_bd_v[i].sw_id_offset = (u32)skb;
+ priv->rx_bd_v[i].phys =
+ dma_map_single(ndev->dev.parent,
+ skb->data,
+ NIXGE_MAX_JUMBO_FRAME_SIZE,
+ DMA_FROM_DEVICE);
+ priv->rx_bd_v[i].cntrl = NIXGE_MAX_JUMBO_FRAME_SIZE;
+ }
+
+ /* Start updating the Rx channel control register */
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+ ((priv->coalesce_count_rx) << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+ (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Write to the Rx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET, cr);
+
+ /* Start updating the Tx channel control register */
+ cr = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+ ((priv->coalesce_count_tx) << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+ (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Write to the Tx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CR_OFFSET, cr);
+
+ /* Populate the tail pointer and bring the Rx Axi DMA engine out of
+ * halted state. This will make the Rx side ready for reception.
+ */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CDESC_OFFSET, priv->rx_bd_p);
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_TDESC_OFFSET, priv->rx_bd_p +
+ (sizeof(*priv->rx_bd_v) * (RX_BD_NUM - 1)));
+
+ /* Write to the RS (Run-stop) bit in the Tx channel control register.
+ * Tx channel is now ready to run. But only after we write to the
+ * tail pointer register that the Tx channel will start transmitting.
+ */
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CDESC_OFFSET, priv->tx_bd_p);
+ cr = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+
+ return 0;
+out:
+ nixge_hw_dma_bd_release(ndev);
+ return -ENOMEM;
+}
+
+static void __nixge_device_reset(struct nixge_priv *priv, off_t offset)
+{
+ u32 status;
+ int err;
+ /* Reset Axi DMA. This would reset NIXGE Ethernet core as well.
+ * The reset process of Axi DMA takes a while to complete as all
+ * pending commands/transfers will be flushed or completed during
+ * this reset process.
+ */
+ nixge_dma_write_reg(priv, offset, XAXIDMA_CR_RESET_MASK);
+ err = nixge_dma_poll_timeout(priv, offset, status,
+ !(status & XAXIDMA_CR_RESET_MASK), 10,
+ 1000);
+ if (err)
+ netdev_err(priv->ndev, "%s: DMA reset timeout!\n", __func__);
+}
+
+static void nixge_device_reset(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ __nixge_device_reset(priv, XAXIDMA_TX_CR_OFFSET);
+ __nixge_device_reset(priv, XAXIDMA_RX_CR_OFFSET);
+
+ priv->max_frm_size = NIXGE_MAX_JUMBO_FRAME_SIZE;
+
+ if (ndev->mtu > NIXGE_MTU && ndev->mtu <= NIXGE_JUMBO_MTU)
+ priv->max_frm_size = ndev->mtu +
+ NIXGE_HDR_SIZE + NIXGE_TRL_SIZE;
+
+ if (nixge_hw_dma_bd_init(ndev))
+ netdev_err(ndev, "%s: descriptor allocation failed\n",
+ __func__);
+
+ netif_trans_update(ndev);
+}
+
+static void nixge_handle_link_change(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ struct phy_device *phydev = ndev->phydev;
+
+ if (phydev->link != priv->link || phydev->speed != priv->speed ||
+ phydev->duplex != priv->duplex) {
+ priv->link = phydev->link;
+ priv->speed = phydev->speed;
+ priv->duplex = phydev->duplex;
+ phy_print_status(phydev);
+ }
+}
+
+static void nixge_tx_skb_unmap(struct nixge_priv *priv,
+ struct nixge_tx_skb *tx_skb)
+{
+ if (tx_skb->mapping) {
+ if (tx_skb->mapped_as_page)
+ dma_unmap_page(priv->ndev->dev.parent, tx_skb->mapping,
+ tx_skb->size, DMA_TO_DEVICE);
+ else
+ dma_unmap_single(priv->ndev->dev.parent,
+ tx_skb->mapping,
+ tx_skb->size, DMA_TO_DEVICE);
+ tx_skb->mapping = 0;
+ }
+
+ if (tx_skb->skb) {
+ dev_kfree_skb_any(tx_skb->skb);
+ tx_skb->skb = NULL;
+ }
+}
+
+static void nixge_start_xmit_done(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ struct nixge_hw_dma_bd *cur_p;
+ struct nixge_tx_skb *tx_skb;
+ unsigned int status = 0;
+ u32 packets = 0;
+ u32 size = 0;
+
+ cur_p = &priv->tx_bd_v[priv->tx_bd_ci];
+ tx_skb = &priv->tx_skb[priv->tx_bd_ci];
+
+ status = cur_p->status;
+
+ while (status & XAXIDMA_BD_STS_COMPLETE_MASK) {
+ nixge_tx_skb_unmap(priv, tx_skb);
+ cur_p->status = 0;
+
+ size += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+ packets++;
+
+ ++priv->tx_bd_ci;
+ priv->tx_bd_ci %= TX_BD_NUM;
+ cur_p = &priv->tx_bd_v[priv->tx_bd_ci];
+ tx_skb = &priv->tx_skb[priv->tx_bd_ci];
+ status = cur_p->status;
+ }
+
+ ndev->stats.tx_packets += packets;
+ ndev->stats.tx_bytes += size;
+
+ if (packets)
+ netif_wake_queue(ndev);
+}
+
+static int nixge_check_tx_bd_space(struct nixge_priv *priv,
+ int num_frag)
+{
+ struct nixge_hw_dma_bd *cur_p;
+
+ cur_p = &priv->tx_bd_v[(priv->tx_bd_tail + num_frag) % TX_BD_NUM];
+ if (cur_p->status & XAXIDMA_BD_STS_ALL_MASK)
+ return NETDEV_TX_BUSY;
+ return 0;
+}
+
+static int nixge_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ struct nixge_hw_dma_bd *cur_p;
+ struct nixge_tx_skb *tx_skb;
+ dma_addr_t tail_p;
+ skb_frag_t *frag;
+ u32 num_frag;
+ u32 ii;
+
+ num_frag = skb_shinfo(skb)->nr_frags;
+ cur_p = &priv->tx_bd_v[priv->tx_bd_tail];
+ tx_skb = &priv->tx_skb[priv->tx_bd_tail];
+
+ if (nixge_check_tx_bd_space(priv, num_frag)) {
+ if (!netif_queue_stopped(ndev))
+ netif_stop_queue(ndev);
+ return NETDEV_TX_OK;
+ }
+
+ cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
+ skb_headlen(skb), DMA_TO_DEVICE);
+ if (dma_mapping_error(ndev->dev.parent, cur_p->phys))
+ goto drop;
+
+ cur_p->cntrl = skb_headlen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK;
+
+ tx_skb->skb = NULL;
+ tx_skb->mapping = cur_p->phys;
+ tx_skb->size = skb_headlen(skb);
+ tx_skb->mapped_as_page = false;
+
+ for (ii = 0; ii < num_frag; ii++) {
+ ++priv->tx_bd_tail;
+ priv->tx_bd_tail %= TX_BD_NUM;
+ cur_p = &priv->tx_bd_v[priv->tx_bd_tail];
+ tx_skb = &priv->tx_skb[priv->tx_bd_tail];
+ frag = &skb_shinfo(skb)->frags[ii];
+
+ cur_p->phys = skb_frag_dma_map(ndev->dev.parent, frag, 0,
+ skb_frag_size(frag),
+ DMA_TO_DEVICE);
+ if (dma_mapping_error(ndev->dev.parent, cur_p->phys))
+ goto frag_err;
+
+ cur_p->cntrl = skb_frag_size(frag);
+
+ tx_skb->skb = NULL;
+ tx_skb->mapping = cur_p->phys;
+ tx_skb->size = skb_frag_size(frag);
+ tx_skb->mapped_as_page = true;
+ }
+
+ /* last buffer of the frame */
+ tx_skb->skb = skb;
+
+ cur_p->cntrl |= XAXIDMA_BD_CTRL_TXEOF_MASK;
+ cur_p->app4 = (unsigned long)skb;
+
+ tail_p = priv->tx_bd_p + sizeof(*priv->tx_bd_v) * priv->tx_bd_tail;
+ /* Start the transfer */
+ nixge_dma_write_reg(priv, XAXIDMA_TX_TDESC_OFFSET, tail_p);
+ ++priv->tx_bd_tail;
+ priv->tx_bd_tail %= TX_BD_NUM;
+
+ return NETDEV_TX_OK;
+frag_err:
+ for (; ii > 0; ii--) {
+ if (priv->tx_bd_tail)
+ priv->tx_bd_tail--;
+ else
+ priv->tx_bd_tail = TX_BD_NUM - 1;
+
+ tx_skb = &priv->tx_skb[priv->tx_bd_tail];
+ nixge_tx_skb_unmap(priv, tx_skb);
+
+ cur_p = &priv->tx_bd_v[priv->tx_bd_tail];
+ cur_p->status = 0;
+ }
+ dma_unmap_single(priv->ndev->dev.parent,
+ tx_skb->mapping,
+ tx_skb->size, DMA_TO_DEVICE);
+drop:
+ ndev->stats.tx_dropped++;
+ return NETDEV_TX_OK;
+}
+
+static int nixge_recv(struct net_device *ndev, int budget)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ struct sk_buff *skb, *new_skb;
+ struct nixge_hw_dma_bd *cur_p;
+ dma_addr_t tail_p = 0;
+ u32 packets = 0;
+ u32 length = 0;
+ u32 size = 0;
+
+ cur_p = &priv->rx_bd_v[priv->rx_bd_ci];
+
+ while ((cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK &&
+ budget > packets)) {
+ tail_p = priv->rx_bd_p + sizeof(*priv->rx_bd_v) *
+ priv->rx_bd_ci;
+
+ skb = (struct sk_buff *)(cur_p->sw_id_offset);
+
+ length = cur_p->status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+ if (length > NIXGE_MAX_JUMBO_FRAME_SIZE)
+ length = NIXGE_MAX_JUMBO_FRAME_SIZE;
+
+ dma_unmap_single(ndev->dev.parent, cur_p->phys,
+ NIXGE_MAX_JUMBO_FRAME_SIZE,
+ DMA_FROM_DEVICE);
+
+ skb_put(skb, length);
+
+ skb->protocol = eth_type_trans(skb, ndev);
+ skb_checksum_none_assert(skb);
+
+ /* For now mark them as CHECKSUM_NONE since
+ * we don't have offload capabilities
+ */
+ skb->ip_summed = CHECKSUM_NONE;
+
+ napi_gro_receive(&priv->napi, skb);
+
+ size += length;
+ packets++;
+
+ new_skb = netdev_alloc_skb_ip_align(ndev,
+ NIXGE_MAX_JUMBO_FRAME_SIZE);
+ if (!new_skb)
+ return packets;
+
+ cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
+ NIXGE_MAX_JUMBO_FRAME_SIZE,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(ndev->dev.parent, cur_p->phys)) {
+ /* FIXME: bail out and clean up */
+ netdev_err(ndev, "Failed to map ...\n");
+ }
+ cur_p->cntrl = NIXGE_MAX_JUMBO_FRAME_SIZE;
+ cur_p->status = 0;
+ cur_p->sw_id_offset = (u32)new_skb;
+
+ ++priv->rx_bd_ci;
+ priv->rx_bd_ci %= RX_BD_NUM;
+ cur_p = &priv->rx_bd_v[priv->rx_bd_ci];
+ }
+
+ ndev->stats.rx_packets += packets;
+ ndev->stats.rx_bytes += size;
+
+ if (tail_p)
+ nixge_dma_write_reg(priv, XAXIDMA_RX_TDESC_OFFSET, tail_p);
+
+ return packets;
+}
+
+static int nixge_poll(struct napi_struct *napi, int budget)
+{
+ struct nixge_priv *priv = container_of(napi, struct nixge_priv, napi);
+ int work_done;
+ u32 status, cr;
+
+ work_done = 0;
+
+ work_done = nixge_recv(priv->ndev, budget);
+ if (work_done < budget) {
+ napi_complete_done(napi, work_done);
+ status = nixge_dma_read_reg(priv, XAXIDMA_RX_SR_OFFSET);
+
+ if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+ /* If there's more, reschedule, but clear */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_SR_OFFSET, status);
+ napi_reschedule(napi);
+ } else {
+ /* if not, turn on RX IRQs again ... */
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ cr |= (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET, cr);
+ }
+ }
+
+ return work_done;
+}
+
+static irqreturn_t nixge_tx_irq(int irq, void *_ndev)
+{
+ struct nixge_priv *priv = netdev_priv(_ndev);
+ struct net_device *ndev = _ndev;
+ unsigned int status;
+ u32 cr;
+
+ status = nixge_dma_read_reg(priv, XAXIDMA_TX_SR_OFFSET);
+ if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+ nixge_dma_write_reg(priv, XAXIDMA_TX_SR_OFFSET, status);
+ nixge_start_xmit_done(priv->ndev);
+ goto out;
+ }
+ if (!(status & XAXIDMA_IRQ_ALL_MASK)) {
+ netdev_err(ndev, "No interrupts asserted in Tx path\n");
+ return IRQ_NONE;
+ }
+ if (status & XAXIDMA_IRQ_ERROR_MASK) {
+ netdev_err(ndev, "DMA Tx error 0x%x\n", status);
+ netdev_err(ndev, "Current BD is at: 0x%x\n",
+ (priv->tx_bd_v[priv->tx_bd_ci]).phys);
+
+ cr = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Write to the Tx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CR_OFFSET, cr);
+
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Write to the Rx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET, cr);
+
+ tasklet_schedule(&priv->dma_err_tasklet);
+ nixge_dma_write_reg(priv, XAXIDMA_TX_SR_OFFSET, status);
+ }
+out:
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t nixge_rx_irq(int irq, void *_ndev)
+{
+ struct nixge_priv *priv = netdev_priv(_ndev);
+ struct net_device *ndev = _ndev;
+ unsigned int status;
+ u32 cr;
+
+ status = nixge_dma_read_reg(priv, XAXIDMA_RX_SR_OFFSET);
+ if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+ /* Turn of IRQs because NAPI */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_SR_OFFSET, status);
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ cr &= ~(XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET, cr);
+
+ if (napi_schedule_prep(&priv->napi))
+ __napi_schedule(&priv->napi);
+ goto out;
+ }
+ if (!(status & XAXIDMA_IRQ_ALL_MASK)) {
+ netdev_err(ndev, "No interrupts asserted in Rx path\n");
+ return IRQ_NONE;
+ }
+ if (status & XAXIDMA_IRQ_ERROR_MASK) {
+ netdev_err(ndev, "DMA Rx error 0x%x\n", status);
+ netdev_err(ndev, "Current BD is at: 0x%x\n",
+ (priv->rx_bd_v[priv->rx_bd_ci]).phys);
+
+ cr = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Finally write to the Tx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CR_OFFSET, cr);
+
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* write to the Rx channel control register */
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET, cr);
+
+ tasklet_schedule(&priv->dma_err_tasklet);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_SR_OFFSET, status);
+ }
+out:
+ return IRQ_HANDLED;
+}
+
+static void nixge_dma_err_handler(unsigned long data)
+{
+ struct nixge_priv *lp = (struct nixge_priv *)data;
+ struct nixge_hw_dma_bd *cur_p;
+ struct nixge_tx_skb *tx_skb;
+ u32 cr, i;
+
+ __nixge_device_reset(lp, XAXIDMA_TX_CR_OFFSET);
+ __nixge_device_reset(lp, XAXIDMA_RX_CR_OFFSET);
+
+ for (i = 0; i < TX_BD_NUM; i++) {
+ cur_p = &lp->tx_bd_v[i];
+ tx_skb = &lp->tx_skb[i];
+ nixge_tx_skb_unmap(lp, tx_skb);
+
+ cur_p->phys = 0;
+ cur_p->cntrl = 0;
+ cur_p->status = 0;
+ cur_p->app0 = 0;
+ cur_p->app1 = 0;
+ cur_p->app2 = 0;
+ cur_p->app3 = 0;
+ cur_p->app4 = 0;
+ cur_p->sw_id_offset = 0;
+ }
+
+ for (i = 0; i < RX_BD_NUM; i++) {
+ cur_p = &lp->rx_bd_v[i];
+ cur_p->status = 0;
+ cur_p->app0 = 0;
+ cur_p->app1 = 0;
+ cur_p->app2 = 0;
+ cur_p->app3 = 0;
+ cur_p->app4 = 0;
+ }
+
+ lp->tx_bd_ci = 0;
+ lp->tx_bd_tail = 0;
+ lp->rx_bd_ci = 0;
+
+ /* Start updating the Rx channel control register */
+ cr = nixge_dma_read_reg(lp, XAXIDMA_RX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+ (XAXIDMA_DFT_RX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+ (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Finally write to the Rx channel control register */
+ nixge_dma_write_reg(lp, XAXIDMA_RX_CR_OFFSET, cr);
+
+ /* Start updating the Tx channel control register */
+ cr = nixge_dma_read_reg(lp, XAXIDMA_TX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+ (XAXIDMA_DFT_TX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+ (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Finally write to the Tx channel control register */
+ nixge_dma_write_reg(lp, XAXIDMA_TX_CR_OFFSET, cr);
+
+ /* Populate the tail pointer and bring the Rx Axi DMA engine out of
+ * halted state. This will make the Rx side ready for reception.
+ */
+ nixge_dma_write_reg(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
+ cr = nixge_dma_read_reg(lp, XAXIDMA_RX_CR_OFFSET);
+ nixge_dma_write_reg(lp, XAXIDMA_RX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+ nixge_dma_write_reg(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
+ (sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
+
+ /* Write to the RS (Run-stop) bit in the Tx channel control register.
+ * Tx channel is now ready to run. But only after we write to the
+ * tail pointer register that the Tx channel will start transmitting
+ */
+ nixge_dma_write_reg(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
+ cr = nixge_dma_read_reg(lp, XAXIDMA_TX_CR_OFFSET);
+ nixge_dma_write_reg(lp, XAXIDMA_TX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+}
+
+static int nixge_open(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ struct phy_device *phy;
+ int ret;
+
+ nixge_device_reset(ndev);
+
+ phy = of_phy_connect(ndev, priv->phy_node,
+ &nixge_handle_link_change, 0, priv->phy_mode);
+ if (!phy)
+ return -ENODEV;
+
+ phy_start(phy);
+
+ /* Enable tasklets for Axi DMA error handling */
+ tasklet_init(&priv->dma_err_tasklet, nixge_dma_err_handler,
+ (unsigned long)priv);
+
+ napi_enable(&priv->napi);
+
+ /* Enable interrupts for Axi DMA Tx */
+ ret = request_irq(priv->tx_irq, nixge_tx_irq, 0, ndev->name, ndev);
+ if (ret)
+ goto err_tx_irq;
+ /* Enable interrupts for Axi DMA Rx */
+ ret = request_irq(priv->rx_irq, nixge_rx_irq, 0, ndev->name, ndev);
+ if (ret)
+ goto err_rx_irq;
+
+ netif_start_queue(ndev);
+
+ return 0;
+
+err_rx_irq:
+ free_irq(priv->tx_irq, ndev);
+err_tx_irq:
+ tasklet_kill(&priv->dma_err_tasklet);
+ netdev_err(ndev, "request_irq() failed\n");
+ return ret;
+}
+
+static int nixge_stop(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ u32 cr;
+
+ netif_stop_queue(ndev);
+ napi_disable(&priv->napi);
+
+ if (ndev->phydev)
+ phy_stop(ndev->phydev);
+
+ cr = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ nixge_dma_write_reg(priv, XAXIDMA_RX_CR_OFFSET,
+ cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+ cr = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ nixge_dma_write_reg(priv, XAXIDMA_TX_CR_OFFSET,
+ cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+
+ tasklet_kill(&priv->dma_err_tasklet);
+
+ free_irq(priv->tx_irq, ndev);
+ free_irq(priv->rx_irq, ndev);
+
+ nixge_hw_dma_bd_release(ndev);
+
+ return 0;
+}
+
+static int nixge_change_mtu(struct net_device *ndev, int new_mtu)
+{
+ if (netif_running(ndev))
+ return -EBUSY;
+
+ if ((new_mtu + NIXGE_HDR_SIZE + NIXGE_TRL_SIZE) >
+ NIXGE_MAX_JUMBO_FRAME_SIZE)
+ return -EINVAL;
+
+ ndev->mtu = new_mtu;
+
+ return 0;
+}
+
+static s32 __nixge_hw_set_mac_address(struct net_device *ndev)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MAC_LSB,
+ (ndev->dev_addr[2]) << 24 |
+ (ndev->dev_addr[3] << 16) |
+ (ndev->dev_addr[4] << 8) |
+ (ndev->dev_addr[5] << 0));
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MAC_MSB,
+ (ndev->dev_addr[1] | (ndev->dev_addr[0] << 8)));
+
+ return 0;
+}
+
+static int nixge_net_set_mac_address(struct net_device *ndev, void *p)
+{
+ int err;
+
+ err = eth_mac_addr(ndev, p);
+ if (!err)
+ __nixge_hw_set_mac_address(ndev);
+
+ return err;
+}
+
+static const struct net_device_ops nixge_netdev_ops = {
+ .ndo_open = nixge_open,
+ .ndo_stop = nixge_stop,
+ .ndo_start_xmit = nixge_start_xmit,
+ .ndo_change_mtu = nixge_change_mtu,
+ .ndo_set_mac_address = nixge_net_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+static void nixge_ethtools_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *ed)
+{
+ strlcpy(ed->driver, "nixge", sizeof(ed->driver));
+ strlcpy(ed->bus_info, "platform", sizeof(ed->driver));
+}
+
+static int nixge_ethtools_get_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ecoalesce)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ u32 regval = 0;
+
+ regval = nixge_dma_read_reg(priv, XAXIDMA_RX_CR_OFFSET);
+ ecoalesce->rx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
+ >> XAXIDMA_COALESCE_SHIFT;
+ regval = nixge_dma_read_reg(priv, XAXIDMA_TX_CR_OFFSET);
+ ecoalesce->tx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
+ >> XAXIDMA_COALESCE_SHIFT;
+ return 0;
+}
+
+static int nixge_ethtools_set_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ecoalesce)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ netdev_err(ndev,
+ "Please stop netif before applying configuration\n");
+ return -EBUSY;
+ }
+
+ if (ecoalesce->rx_coalesce_usecs ||
+ ecoalesce->rx_coalesce_usecs_irq ||
+ ecoalesce->rx_max_coalesced_frames_irq ||
+ ecoalesce->tx_coalesce_usecs ||
+ ecoalesce->tx_coalesce_usecs_irq ||
+ ecoalesce->tx_max_coalesced_frames_irq ||
+ ecoalesce->stats_block_coalesce_usecs ||
+ ecoalesce->use_adaptive_rx_coalesce ||
+ ecoalesce->use_adaptive_tx_coalesce ||
+ ecoalesce->pkt_rate_low ||
+ ecoalesce->rx_coalesce_usecs_low ||
+ ecoalesce->rx_max_coalesced_frames_low ||
+ ecoalesce->tx_coalesce_usecs_low ||
+ ecoalesce->tx_max_coalesced_frames_low ||
+ ecoalesce->pkt_rate_high ||
+ ecoalesce->rx_coalesce_usecs_high ||
+ ecoalesce->rx_max_coalesced_frames_high ||
+ ecoalesce->tx_coalesce_usecs_high ||
+ ecoalesce->tx_max_coalesced_frames_high ||
+ ecoalesce->rate_sample_interval)
+ return -EOPNOTSUPP;
+ if (ecoalesce->rx_max_coalesced_frames)
+ priv->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;
+ if (ecoalesce->tx_max_coalesced_frames)
+ priv->coalesce_count_tx = ecoalesce->tx_max_coalesced_frames;
+
+ return 0;
+}
+
+static int nixge_ethtools_set_phys_id(struct net_device *ndev,
+ enum ethtool_phys_id_state state)
+{
+ struct nixge_priv *priv = netdev_priv(ndev);
+ u32 ctrl;
+
+ ctrl = nixge_ctrl_read_reg(priv, NIXGE_REG_LED_CTL);
+ switch (state) {
+ case ETHTOOL_ID_ACTIVE:
+ ctrl |= NIXGE_ID_LED_CTL_EN;
+ /* Enable identification LED override*/
+ nixge_ctrl_write_reg(priv, NIXGE_REG_LED_CTL, ctrl);
+ return 2;
+
+ case ETHTOOL_ID_ON:
+ ctrl |= NIXGE_ID_LED_CTL_VAL;
+ nixge_ctrl_write_reg(priv, NIXGE_REG_LED_CTL, ctrl);
+ break;
+
+ case ETHTOOL_ID_OFF:
+ ctrl &= ~NIXGE_ID_LED_CTL_VAL;
+ nixge_ctrl_write_reg(priv, NIXGE_REG_LED_CTL, ctrl);
+ break;
+
+ case ETHTOOL_ID_INACTIVE:
+ /* Restore LED settings */
+ ctrl &= ~NIXGE_ID_LED_CTL_EN;
+ nixge_ctrl_write_reg(priv, NIXGE_REG_LED_CTL, ctrl);
+ break;
+ }
+
+ return 0;
+}
+
+static const struct ethtool_ops nixge_ethtool_ops = {
+ .get_drvinfo = nixge_ethtools_get_drvinfo,
+ .get_coalesce = nixge_ethtools_get_coalesce,
+ .set_coalesce = nixge_ethtools_set_coalesce,
+ .set_phys_id = nixge_ethtools_set_phys_id,
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_link = ethtool_op_get_link,
+};
+
+static int nixge_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+ struct nixge_priv *priv = bus->priv;
+ u32 status, tmp;
+ int err;
+ u16 device;
+
+ if (reg & MII_ADDR_C45) {
+ device = (reg >> 16) & 0x1f;
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_ADDR, reg & 0xffff);
+
+ tmp = NIXGE_MDIO_CLAUSE45 | NIXGE_MDIO_OP(NIXGE_MDIO_OP_ADDRESS)
+ | NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_OP, tmp);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_CTRL, 1);
+
+ err = nixge_ctrl_poll_timeout(priv, NIXGE_REG_MDIO_CTRL, status,
+ !status, 10, 1000);
+ if (err) {
+ dev_err(priv->dev, "timeout setting address");
+ return err;
+ }
+
+ tmp = NIXGE_MDIO_CLAUSE45 | NIXGE_MDIO_OP(NIXGE_MDIO_OP_READ) |
+ NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+ } else {
+ device = reg & 0x1f;
+
+ tmp = NIXGE_MDIO_CLAUSE22 | NIXGE_MDIO_OP(MDIO_C22_READ) |
+ NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+ }
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_OP, tmp);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_CTRL, 1);
+
+ err = nixge_ctrl_poll_timeout(priv, NIXGE_REG_MDIO_CTRL, status,
+ !status, 10, 1000);
+ if (err) {
+ dev_err(priv->dev, "timeout setting read command");
+ return err;
+ }
+
+ status = nixge_ctrl_read_reg(priv, NIXGE_REG_MDIO_DATA);
+
+ return status;
+}
+
+static int nixge_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 val)
+{
+ struct nixge_priv *priv = bus->priv;
+ u32 status, tmp;
+ u16 device;
+ int err;
+
+ if (reg & MII_ADDR_C45) {
+ device = (reg >> 16) & 0x1f;
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_ADDR, reg & 0xffff);
+
+ tmp = NIXGE_MDIO_CLAUSE45 | NIXGE_MDIO_OP(NIXGE_MDIO_OP_ADDRESS)
+ | NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_OP, tmp);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_CTRL, 1);
+
+ err = nixge_ctrl_poll_timeout(priv, NIXGE_REG_MDIO_CTRL, status,
+ !status, 10, 1000);
+ if (err) {
+ dev_err(priv->dev, "timeout setting address");
+ return err;
+ }
+
+ tmp = NIXGE_MDIO_CLAUSE45 | NIXGE_MDIO_OP(NIXGE_MDIO_OP_WRITE)
+ | NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_DATA, val);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_OP, tmp);
+ err = nixge_ctrl_poll_timeout(priv, NIXGE_REG_MDIO_CTRL, status,
+ !status, 10, 1000);
+ if (err)
+ dev_err(priv->dev, "timeout setting write command");
+ } else {
+ device = reg & 0x1f;
+
+ tmp = NIXGE_MDIO_CLAUSE22 | NIXGE_MDIO_OP(MDIO_C22_WRITE) |
+ NIXGE_MDIO_ADDR(phy_id) | NIXGE_MDIO_MMD(device);
+
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_DATA, val);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_OP, tmp);
+ nixge_ctrl_write_reg(priv, NIXGE_REG_MDIO_CTRL, 1);
+
+ err = nixge_ctrl_poll_timeout(priv, NIXGE_REG_MDIO_CTRL, status,
+ !status, 10, 1000);
+ if (err)
+ dev_err(priv->dev, "timeout setting write command");
+ }
+
+ return err;
+}
+
+static int nixge_mdio_setup(struct nixge_priv *priv, struct device_node *np)
+{
+ struct mii_bus *bus;
+ int err;
+
+ bus = mdiobus_alloc();
+ if (!bus)
+ return -ENOMEM;
+
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(priv->dev));
+ bus->priv = priv;
+ bus->name = "nixge_mii_bus";
+ bus->read = nixge_mdio_read;
+ bus->write = nixge_mdio_write;
+ bus->parent = priv->dev;
+
+ priv->mii_bus = bus;
+ err = of_mdiobus_register(bus, np);
+ if (err)
+ goto err_register;
+
+ return 0;
+
+err_register:
+ mdiobus_free(bus);
+ return err;
+}
+
+static void *nixge_get_nvmem_address(struct device *dev)
+{
+ struct nvmem_cell *cell;
+ size_t cell_size;
+ char *mac;
+
+ cell = nvmem_cell_get(dev, "address");
+ if (IS_ERR(cell))
+ return cell;
+
+ mac = nvmem_cell_read(cell, &cell_size);
+ nvmem_cell_put(cell);
+
+ return mac;
+}
+
+static int nixge_probe(struct platform_device *pdev)
+{
+ struct nixge_priv *priv;
+ struct net_device *ndev;
+ struct resource *dmares;
+ const char *mac_addr;
+ int err;
+
+ ndev = alloc_etherdev(sizeof(*priv));
+ if (!ndev)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, ndev);
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+
+ ndev->features = NETIF_F_SG;
+ ndev->netdev_ops = &nixge_netdev_ops;
+ ndev->ethtool_ops = &nixge_ethtool_ops;
+
+ /* MTU range: 64 - 9000 */
+ ndev->min_mtu = 64;
+ ndev->max_mtu = NIXGE_JUMBO_MTU;
+
+ mac_addr = nixge_get_nvmem_address(&pdev->dev);
+ if (mac_addr && is_valid_ether_addr(mac_addr))
+ ether_addr_copy(ndev->dev_addr, mac_addr);
+ else
+ eth_hw_addr_random(ndev);
+
+ priv = netdev_priv(ndev);
+ priv->ndev = ndev;
+ priv->dev = &pdev->dev;
+
+ netif_napi_add(ndev, &priv->napi, nixge_poll, NAPI_POLL_WEIGHT);
+
+ dmares = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->dma_regs = devm_ioremap_resource(&pdev->dev, dmares);
+ if (IS_ERR(priv->dma_regs)) {
+ netdev_err(ndev, "failed to map dma regs\n");
+ return PTR_ERR(priv->dma_regs);
+ }
+ priv->ctrl_regs = priv->dma_regs + NIXGE_REG_CTRL_OFFSET;
+ __nixge_hw_set_mac_address(ndev);
+
+ priv->tx_irq = platform_get_irq_byname(pdev, "tx");
+ if (priv->tx_irq < 0) {
+ netdev_err(ndev, "could not find 'tx' irq");
+ return priv->tx_irq;
+ }
+
+ priv->rx_irq = platform_get_irq_byname(pdev, "rx");
+ if (priv->rx_irq < 0) {
+ netdev_err(ndev, "could not find 'rx' irq");
+ return priv->rx_irq;
+ }
+
+ priv->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD;
+ priv->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD;
+
+ err = nixge_mdio_setup(priv, pdev->dev.of_node);
+ if (err) {
+ netdev_err(ndev, "error registering mdio bus");
+ goto free_netdev;
+ }
+
+ priv->phy_mode = of_get_phy_mode(pdev->dev.of_node);
+ if (priv->phy_mode < 0) {
+ netdev_err(ndev, "not find \"phy-mode\" property\n");
+ err = -EINVAL;
+ goto unregister_mdio;
+ }
+
+ priv->phy_node = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
+ if (!priv->phy_node) {
+ netdev_err(ndev, "not find \"phy-handle\" property\n");
+ err = -EINVAL;
+ goto unregister_mdio;
+ }
+
+ err = register_netdev(priv->ndev);
+ if (err) {
+ netdev_err(ndev, "register_netdev() error (%i)\n", err);
+ goto unregister_mdio;
+ }
+
+ return 0;
+
+unregister_mdio:
+ mdiobus_unregister(priv->mii_bus);
+ mdiobus_free(priv->mii_bus);
+
+free_netdev:
+ free_netdev(ndev);
+
+ return err;
+}
+
+static int nixge_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct nixge_priv *priv = netdev_priv(ndev);
+
+ mdiobus_unregister(priv->mii_bus);
+ mdiobus_free(priv->mii_bus);
+
+ unregister_netdev(ndev);
+
+ free_netdev(ndev);
+
+ return 0;
+}
+
+/* Match table for of_platform binding */
+static const struct of_device_id nixge_dt_ids[] = {
+ { .compatible = "ni,xge-enet-2.00", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, nixge_dt_ids);
+
+static struct platform_driver nixge_driver = {
+ .probe = nixge_probe,
+ .remove = nixge_remove,
+ .driver = {
+ .name = "nixge",
+ .of_match_table = of_match_ptr(nixge_dt_ids),
+ },
+};
+module_platform_driver(nixge_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("National Instruments XGE Management MAC");
+MODULE_AUTHOR("Moritz Fischer <mdf@...nel.org>");
--
2.16.1
Powered by blists - more mailing lists