| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1521025722-24205-5-git-send-email-geert+renesas@glider.be>
Date: Wed, 14 Mar 2018 12:08:42 +0100
From: Geert Uytterhoeven <geert+renesas@...der.be>
To: Marek Vasut <marek.vasut+renesas@...il.com>,
Lee Jones <lee.jones@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>
Cc: linux-renesas-soc@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Geert Uytterhoeven <geert+renesas@...der.be>
Subject: [PATCH v2 4/4] regulator: bd9571mwv: Add support for DDR backup mode
The BD9571MWV PMIC supports DDR backup mode, which keeps one or more DDR
rails powered while the main SoC is powered down.
Which DDR rails are to be kept powered is board-specific, and controlled
using the optional "rohm,ddr-backup-power" DT property. In the absence
of this property, backup mode is not available.
Backup mode can be enabled or disabled by the user using the standard
"wakeup" virtual file in sysfs, e.g. to enable:
echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup
When the PMIC is configured for backup mode, the role of the accessory
power switch changes from a power switch to a wake-up switch.
Two types of switches (or signals) can be used:
A. With a momentary power switch (or pulse signal), the PMIC is
configured for backup mode in the PMIC driver's suspend callback,
during system suspend.
Backup mode is enabled by default, as there is no further impact
during normal system operation.
B. With a toggle power switch (or level signal), the following steps
must be followed exactly:
1. Configure PMIC for backup mode,
2. Switch accessory power switch off, to prepare for system
suspend, which is a manual step not controlled by software,
3. Suspend system.
This mode is not yet supported by the driver.
As the switch type is board-specific, and cannot be determined
automatically, it is obtained from the presence of one of the
"rohm,rstbmode-*" properties in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@...der.be>
---
v2:
- Use normal "wakeup" sysfs virtual file instead of adding our own
"backup_mode" file,
- Differentiate between momentary and toggle power switches:
- Support for momentary switches is enabled automatically,
- Toggle switches are not yet supported (but still work when
backup mode is enabled using i2set from userspace).
---
drivers/regulator/bd9571mwv-regulator.c | 127 +++++++++++++++++++++++++++++++-
1 file changed, 126 insertions(+), 1 deletion(-)
diff --git a/drivers/regulator/bd9571mwv-regulator.c b/drivers/regulator/bd9571mwv-regulator.c
index c67a83d53c4cb76b..be574eb444ebda97 100644
--- a/drivers/regulator/bd9571mwv-regulator.c
+++ b/drivers/regulator/bd9571mwv-regulator.c
@@ -24,6 +24,18 @@
#include <linux/mfd/bd9571mwv.h>
+struct bd9571mwv_reg {
+ struct bd9571mwv *bd;
+
+ /* DDR Backup Power */
+ u8 bkup_mode_cnt_keepon; /* from "rohm,ddr-backup-power" */
+ u8 bkup_mode_cnt_saved;
+
+ /* Power switch type */
+ bool rstbmode_level;
+ bool rstbmode_pulse;
+};
+
enum bd9571mwv_regulators { VD09, VD18, VD25, VD33, DVFS };
#define BD9571MWV_REG(_name, _of, _id, _ops, _vr, _vm, _nv, _min, _step, _lmin)\
@@ -131,14 +143,99 @@ static struct regulator_desc regulators[] = {
0x80, 600000, 10000, 0x3c),
};
+#ifdef CONFIG_PM_SLEEP
+static int bd9571mwv_bkup_mode_read(struct bd9571mwv *bd, unsigned int *mode)
+{
+ int ret;
+
+ ret = regmap_read(bd->regmap, BD9571MWV_BKUP_MODE_CNT, mode);
+ if (ret) {
+ dev_err(bd->dev, "failed to read backup mode (%d)\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int bd9571mwv_bkup_mode_write(struct bd9571mwv *bd, unsigned int mode)
+{
+ int ret;
+
+ ret = regmap_write(bd->regmap, BD9571MWV_BKUP_MODE_CNT, mode);
+ if (ret) {
+ dev_err(bd->dev, "failed to configure backup mode 0x%x (%d)\n",
+ mode, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int bd9571mwv_suspend(struct device *dev)
+{
+ struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
+ unsigned int mode;
+ int ret;
+
+ if (!device_may_wakeup(dev))
+ return 0;
+
+ /* Save DDR Backup Mode */
+ ret = bd9571mwv_bkup_mode_read(bdreg->bd, &mode);
+ if (ret)
+ return ret;
+
+ bdreg->bkup_mode_cnt_saved = mode;
+
+ if (!bdreg->rstbmode_pulse)
+ return 0;
+
+ /* Enable DDR Backup Mode */
+ mode &= ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK;
+ mode |= bdreg->bkup_mode_cnt_keepon;
+
+ if (mode != bdreg->bkup_mode_cnt_saved)
+ return bd9571mwv_bkup_mode_write(bdreg->bd, mode);
+
+ return 0;
+}
+
+static int bd9571mwv_resume(struct device *dev)
+{
+ struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
+
+ if (!device_may_wakeup(dev))
+ return 0;
+
+ /* Restore DDR Backup Mode */
+ return bd9571mwv_bkup_mode_write(bdreg->bd, bdreg->bkup_mode_cnt_saved);
+}
+
+static const struct dev_pm_ops bd9571mwv_pm = {
+ SET_SYSTEM_SLEEP_PM_OPS(bd9571mwv_suspend, bd9571mwv_resume)
+};
+
+#define DEV_PM_OPS &bd9571mwv_pm
+#else
+#define DEV_PM_OPS NULL
+#endif /* CONFIG_PM_SLEEP */
+
static int bd9571mwv_regulator_probe(struct platform_device *pdev)
{
struct bd9571mwv *bd = dev_get_drvdata(pdev->dev.parent);
struct regulator_config config = { };
+ struct bd9571mwv_reg *bdreg;
struct regulator_dev *rdev;
+ unsigned int val;
int i;
- platform_set_drvdata(pdev, bd);
+ bdreg = devm_kzalloc(&pdev->dev, sizeof(*bdreg), GFP_KERNEL);
+ if (!bdreg)
+ return -ENOMEM;
+
+ bdreg->bd = bd;
+
+ platform_set_drvdata(pdev, bdreg);
config.dev = &pdev->dev;
config.dev->of_node = bd->dev->of_node;
@@ -155,6 +252,33 @@ static int bd9571mwv_regulator_probe(struct platform_device *pdev)
}
}
+ val = 0;
+ of_property_read_u32(bd->dev->of_node, "rohm,ddr-backup-power", &val);
+ if (val & ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK) {
+ dev_err(bd->dev, "invalid %s mode %u\n",
+ "rohm,ddr-backup-power", val);
+ return -EINVAL;
+ }
+ bdreg->bkup_mode_cnt_keepon = val;
+
+ bdreg->rstbmode_level = of_property_read_bool(bd->dev->of_node,
+ "rohm,rstbmode-level");
+ bdreg->rstbmode_pulse = of_property_read_bool(bd->dev->of_node,
+ "rohm,rstbmode-pulse");
+ if (bdreg->rstbmode_level && bdreg->rstbmode_pulse) {
+ dev_err(bd->dev, "only one rohm,rstbmode-* may be specified");
+ return -EINVAL;
+ }
+
+ if (bdreg->bkup_mode_cnt_keepon) {
+ device_set_wakeup_capable(&pdev->dev, true);
+ /*
+ * Wakeup is enabled by default in pulse mode, but needs
+ * explicit user setup in level mode.
+ */
+ device_set_wakeup_enable(&pdev->dev, bdreg->rstbmode_pulse);
+ }
+
return 0;
}
@@ -167,6 +291,7 @@ MODULE_DEVICE_TABLE(platform, bd9571mwv_regulator_id_table);
static struct platform_driver bd9571mwv_regulator_driver = {
.driver = {
.name = "bd9571mwv-regulator",
+ .pm = DEV_PM_OPS,
},
.probe = bd9571mwv_regulator_probe,
.id_table = bd9571mwv_regulator_id_table,
--
2.7.4
Powered by blists - more mailing lists