lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-ID: <20180401153631.GA5700@atomide.com> Date: Sun, 1 Apr 2018 08:36:31 -0700 From: Tony Lindgren <tony@...mide.com> To: Pavel Machek <pavel@....cz> Cc: Sebastian Reichel <sebastian.reichel@...labora.co.uk>, Mark Brown <broonie@...nel.org>, Liam Girdwood <lgirdwood@...il.com>, Rob Herring <robh+dt@...nel.org>, Lee Jones <lee.jones@...aro.org>, Jaroslav Kysela <perex@...ex.cz>, Takashi Iwai <tiwai@...e.com>, alsa-devel@...a-project.org, linux-omap@...r.kernel.org, devicetree@...r.kernel.org, linux-kernel@...r.kernel.org, kernel@...labora.com, Dan Williams <dcbw@...hat.com> Subject: Re: call/normal switch was Re: omap4-droid4: voice call support was * Pavel Machek <pavel@....cz> [180401 13:20]: > On Sat 2018-03-31 16:43:14, Tony Lindgren wrote: > > * Pavel Machek <pavel@....cz> [180331 19:56]: > > > On Sat 2018-03-31 21:46:16, Pavel Machek wrote: > > > > On Sat 2018-03-31 21:19:39, Pavel Machek wrote: > > > > > On Sat 2018-03-31 11:19:35, Tony Lindgren wrote: > > > > > > Cool :) Microphone still does not work for me.. I tried tweaking > > > > > > the alsamixer settings but no mic. This is with cold boot with > > > > > > droid4-kexecboot if that might make a difference, we may have > > > > > > some register uninitialized somewhere. Any ideas? > > > > > > > > > > Ok, I was focusing on the speaker side. > > > > > > > > > > alsamixer, tab to go to capture settings, set it to 37 37 Mic2 Mic1 > > > > > should work, according to my notes, but not recently tested and not > > > > > tested against real human. > > > > > > > > > > I'll attempt to test it, but something in my userland shuts down > > > > > system just after boot 60% of time, which is rather annoying. > > > > > > > > Hmm. So I tried again, and setting Mic1 and back in the capture > > > > settings crashed the modem. Bang, disconnected from the USB. > > > > > > Next try, and it worked this time. > > > > > > _Before the call_, set mode to Normal and then Call. Then go to > > > capture, and set 100 100 Mic2 Mic1. Then place a call, > > > > > > AT+CFUN=1 > > > OK > > > ATD6; > > > > No luck with microphone here :( Using ttyUSB4, AT+CFUN=1 > > works, but ATD command on it just hangs the USB interface > > and I have to reload phy-mapphone-mdm6600 to reset the > > modem. > > Test call with real human worked (thanks to Rolf K.), I could hear him > well but he reported call was very quiet. And that was with capture > settings at 100%. Maybe the volume also needs to be controlled at mdm6600 end. I'm seeing some AT+CLVL=n with n being between [0-7] calls on DLCI2 in my Android logcat logs. > If you had a register dump from android with mics working, preferably > not in speaker mode, perhaps I could try to figure it out? OK here are four diffs against starting the phone app for regular call, speaker call, and muted versions of them: http://muru.com/linux/d4/cpcap/ Also, I'm connected over cdma right now, not 3g, but I doubt that makes a difference for the microphone. Regards, Tony
Powered by blists - more mailing lists