| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1525158789-32255-1-git-send-email-eyalr@ti.com>
Date: Tue, 1 May 2018 10:13:09 +0300
From: Eyal Reizer <eyalreizer@...il.com>
To: bcousson@...libre.com, tony@...mide.com, robh+dt@...nel.org,
mark.rutland@....com, linux-omap@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Cc: Eyal Reizer <eyalr@...com>
Subject: [tiL4.14-CON PATCH v2] ARM: dts: am437x-sk-evm: add wilink8 support
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@...com>
---
arch/arm/boot/dts/am437x-sk-evm.dts | 115 ++++++++++++++++++++++++++++++++++++
1 file changed, 115 insertions(+)
diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts
index 16d9db0..afffdb1 100644
--- a/arch/arm/boot/dts/am437x-sk-evm.dts
+++ b/arch/arm/boot/dts/am437x-sk-evm.dts
@@ -15,6 +15,7 @@
#include <dt-bindings/pwm/pwm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "TI AM437x SK EVM";
@@ -158,6 +159,22 @@
};
};
};
+
+ vmmcwl_fixed: fixedregulator-mmcwl {
+ /*
+ * WL_EN is not SDIO standard compliant. It is an out of band
+ * signal and hard to be dealt with in a standard way by the
+ * SDIO core driver.
+ * So modelling the WL_EN line as a regulator was a natural
+ * choice as the MMC core already deals with MMC supplies.
+ */
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcwl_fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
&am43xx_pinmux {
@@ -424,6 +441,62 @@
AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
>;
};
+
+ mmc3_pins_default: pinmux_mmc3_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */
+ AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */
+ AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD22) cam1_data4.mmc2_dat0 */
+ AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE23) cam1_data5.mmc2_dat1 */
+ AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD23) cam1_data6.mmc2_dat2 */
+ AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE24) cam1_data7.mmc2_dat3 */
+ >;
+ };
+
+ mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */
+ AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */
+ AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD22) cam1_data4.mmc2_dat0 */
+ AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE23) cam1_data5.mmc2_dat1 */
+ AM4372_IOPAD(0xa00, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD23) cam1_data6.mmc2_dat2 */
+ AM4372_IOPAD(0xa04, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE24) cam1_data7.mmc2_dat3 */
+ >;
+ };
+
+ wlan_pins_default: pinmux_wlan_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
+ AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
+ >;
+ };
+
+ wlan_pins_sleep: pinmux_wlan_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
+ AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
+ >;
+ };
+
+ uart1_bt_pins_default: pinmux_uart1_bt_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
+ >;
+ };
+
+ uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rxd.uart1_rxd */
+ AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_txd.uart1_txd */
+ AM4372_IOPAD(0x978, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
+ AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
+ AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
+ >;
+ };
};
&i2c0 {
@@ -606,6 +679,10 @@
status = "okay";
};
+&gpio4 {
+ status = "okay";
+};
+
&gpio5 {
status = "okay";
};
@@ -620,6 +697,44 @@
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_bt_pins_default>;
+ pinctrl-1 = <&uart1_bt_pins_sleep>;
+};
+
+&mmc3 {
+ status = "okay";
+ /*
+ * these are on the crossbar and are outlined in the
+ * xbar-event-map element
+ */
+ dmas = <&edma_xbar 30 0 1>,
+ <&edma_xbar 31 0 2>;
+ dma-names = "tx", "rx";
+ vmmc-supply = <&vmmcwl_fixed>;
+ bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mmc3_pins_default>;
+ pinctrl-1 = <&mmc3_pins_sleep>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ ti,non-removable;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@0 {
+ compatible = "ti,wl1835";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&wlan_pins_default>;
+ pinctrl-1 = <&wlan_pins_sleep>;
+ reg = <2>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
&usb2_phy1 {
status = "okay";
};
--
2.7.4
Powered by blists - more mailing lists