| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20180511103822.31698-7-radu.pirea@microchip.com>
Date: Fri, 11 May 2018 13:38:22 +0300
From: Radu Pirea <radu.pirea@...rochip.com>
To: <devicetree@...r.kernel.org>, <linux-serial@...r.kernel.org>,
<linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>, <linux-spi@...r.kernel.org>
CC: <mark.rutland@....com>, <robh+dt@...nel.org>,
<lee.jones@...aro.org>, <gregkh@...uxfoundation.org>,
<jslaby@...e.com>, <richard.genoud@...il.com>,
<alexandre.belloni@...tlin.com>, <nicolas.ferre@...rochip.com>,
<broonie@...nel.org>, Radu Pirea <radu.pirea@...rochip.com>
Subject: [PATCH v3 6/6] tty/serial: atmel: changed the driver to work under at91-usart mfd
This patch modifies the place where resources and device tree properties
are searched.
Signed-off-by: Radu Pirea <radu.pirea@...rochip.com>
---
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/atmel_serial.c | 29 +++++++++++++++--------------
2 files changed, 16 insertions(+), 14 deletions(-)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 3682fd3e960c..25e55332f8b1 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -119,6 +119,7 @@ config SERIAL_ATMEL
depends on ARCH_AT91 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
+ select MFD_AT91_USART
help
This enables the driver for the on-chip UARTs of the Atmel
AT91 processors.
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index df46a9e88c34..6b4494352853 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -193,8 +193,8 @@ static struct console atmel_console;
#if defined(CONFIG_OF)
static const struct of_device_id atmel_serial_dt_ids[] = {
- { .compatible = "atmel,at91rm9200-usart" },
- { .compatible = "atmel,at91sam9260-usart" },
+ { .compatible = "atmel,at91rm9200-usart-serial" },
+ { .compatible = "atmel,at91sam9260-usart-serial" },
{ /* sentinel */ }
};
#endif
@@ -1631,7 +1631,7 @@ static void atmel_tasklet_tx_func(unsigned long data)
static void atmel_init_property(struct atmel_uart_port *atmel_port,
struct platform_device *pdev)
{
- struct device_node *np = pdev->dev.of_node;
+ struct device_node *np = pdev->dev.parent->of_node;
/* DMA/PDC usage specification */
if (of_property_read_bool(np, "atmel,use-dma-rx")) {
@@ -2223,7 +2223,8 @@ static const char *atmel_type(struct uart_port *port)
static void atmel_release_port(struct uart_port *port)
{
struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ int size = to_platform_device(pdev->dev.parent)->resource[0].end -
+ to_platform_device(pdev->dev.parent)->resource[0].start + 1;
release_mem_region(port->mapbase, size);
@@ -2239,7 +2240,8 @@ static void atmel_release_port(struct uart_port *port)
static int atmel_request_port(struct uart_port *port)
{
struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ int size = to_platform_device(pdev->dev.parent)->resource[0].end -
+ to_platform_device(pdev->dev.parent)->resource[0].start + 1;
if (!request_mem_region(port->mapbase, size, "atmel_serial"))
return -EBUSY;
@@ -2345,23 +2347,23 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
atmel_init_property(atmel_port, pdev);
atmel_set_ops(port);
- uart_get_rs485_mode(&pdev->dev, &port->rs485);
+ uart_get_rs485_mode(pdev->dev.parent, &port->rs485);
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
port->ops = &atmel_pops;
port->fifosize = 1;
port->dev = &pdev->dev;
- port->mapbase = pdev->resource[0].start;
- port->irq = pdev->resource[1].start;
+ port->mapbase = to_platform_device(pdev->dev.parent)->resource[0].start;
+ port->irq = to_platform_device(pdev->dev.parent)->resource[1].start;
port->rs485_config = atmel_config_rs485;
- port->membase = NULL;
+ port->membase = NULL;
memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
/* for console, the clock could already be configured */
if (!atmel_port->clk) {
- atmel_port->clk = clk_get(&pdev->dev, "usart");
+ atmel_port->clk = clk_get(pdev->dev.parent, "usart");
if (IS_ERR(atmel_port->clk)) {
ret = PTR_ERR(atmel_port->clk);
atmel_port->clk = NULL;
@@ -2656,7 +2658,7 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
atmel_port->rts_low = 0;
atmel_port->rts_high = 0;
- if (of_property_read_u32(pdev->dev.of_node,
+ if (of_property_read_u32(pdev->dev.parent->of_node,
"atmel,fifo-size",
&atmel_port->fifo_size))
return;
@@ -2694,11 +2696,10 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
static int atmel_serial_probe(struct platform_device *pdev)
{
struct atmel_uart_port *atmel_port;
- struct device_node *np = pdev->dev.of_node;
+ struct device_node *np = pdev->dev.parent->of_node;
void *data;
int ret = -ENODEV;
bool rs485_enabled;
-
BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
ret = of_alias_get_id(np, "serial");
@@ -2845,7 +2846,7 @@ static struct platform_driver atmel_serial_driver = {
.suspend = atmel_serial_suspend,
.resume = atmel_serial_resume,
.driver = {
- .name = "atmel_usart",
+ .name = "atmel_usart_serial",
.of_match_table = of_match_ptr(atmel_serial_dt_ids),
},
};
--
2.17.0
Powered by blists - more mailing lists