| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAHCN7xL_QbHALJeBaJk9TyfBz5BUYeZHkYR6uyrxXDdnguKjtg@mail.gmail.com>
Date: Wed, 16 May 2018 19:46:54 -0500
From: Adam Ford <aford173@...il.com>
To: David Lechner <david@...hnology.com>
Cc: linux-clk <linux-clk@...r.kernel.org>,
devicetree <devicetree@...r.kernel.org>,
arm-soc <linux-arm-kernel@...ts.infradead.org>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...eaurora.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Sekhar Nori <nsekhar@...com>,
Kevin Hilman <khilman@...nel.org>,
Bartosz Golaszewski <bgolaszewski@...libre.com>,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v10 00/27] ARM: davinci: convert to common clock framework
On Wed, May 9, 2018 at 12:25 PM, David Lechner <david@...hnology.com> wrote:
> This series converts mach-davinci to use the common clock framework.
>
> The series works like this, the first 3 patches fix some issues with the clock
> drivers that have already been accepted into the mainline kernel.
>
> Then, starting with "ARM: davinci: pass clock as parameter to
> davinci_timer_init()", we get the mach code ready for the switch by adding the
> code needed for the new clock drivers and adding #ifndef CONFIG_COMMON_CLK
> around the legacy clocks so that we can switch easily between the old and the
> new.
>
> "ARM: davinci: switch to common clock framework" actually flips the switch
> to start using the new clock drivers. Then the next 8 patches remove all
> of the old clock code.
>
> The final four patches add device tree clock support to the one SoC that
> supports it.
>
> This series has been tested on TI OMAP-L138 LCDK (both device tree and legacy
> board file).
>
I am find. I don't know what I did wrong, but it's working fine. If
you want to add my 'tested-by' go ahead.
Tested-by: Adam Ford <aford173@...il.com> #da850-evm, ethernet, spi
flash, SD, UART
>
> Changes:
>
> v10 changes (also see individual patches for details):
> - Reworked device tree bindings for DaVinci timer.
> - Dropped helper functions to conditionally call devm_* versions of functions
> - Fix some typos
> - Fix some rebasing issues introduced in v9
>
> v9 changes (also see individual patches for details):
> - Rebased on linux-davnci/master (f5e3203bb775)
> - Dropped drivers/clk patches that landed in v4.17
> - New drivers/clk patches for early boot special case
> - New patch for ti,davinci-timer device tree bindings
> - Updated mach/davinci patches to register clocks in early boot when needed
>
> v8 changes (also see individual patches for details):
> - Rebased on linux-davinci/master
> - Dropped use of __init and __initconst attributes in clk drivers
> - Add clkdev lookups for PLL SYSCLKs
> - Fix genpd clock reference counting issue
> - Fix PSC clock driver loading order issue
> - Fix typo in device tree and add more power-domains properties
>
> v7 changes (also see individual patches for details):
> - Rebased on linux-davinci/master (v4.16-rc)
> - Convert clock drivers to platform devices
> - New patch "ARM: davinci: pass clock as parameter to davinci_timer_init()"
> - Fix issues with lcdk and aemif clock lookups and power domains
> - Fixed other minor issues brought up in v6 review
>
> v6 changes (also see individual patches for details):
> - All of the device tree bindings are changed
> - All of the clock drivers are changed significantly
> - Fixed issues brought up during review of v5
> - "ARM: davinci: move davinci_clk_init() to init_time" is removed from this
> series and submitted separately
>
> v5 changes:
> - Basically, this is an entirely new series
> - Patches are broken up into bite-sized pieces
> - Converted PSC clock driver to use regmap
> - Restored "force" flag for certain DA850 clocks
> - Added device tree bindings
> - Moved more of the clock init to drivers/clk
> - Fixed frequency scaling (maybe*)
>
> * I have frequency scaling using cpufreq-dt, so I know the clocks are doing
> what they need to do to make this work, but I haven't figured out how to
> test davinci-cpufreq driver yet. (Patches to make cpufreq-dt work will be
> sent separately after this series has landed.)
>
>
> Dependencies:
>
> There are still some outstanding fixes to get everything working correctly.
> These are all just runtime dependencies and only needed for certain platforms.
>
> - "drm/tilcdc: Fix setting clock divider for omap-l138"[1]
> - "clk: davinci: pll-dm355: fix SYSCLKn parent names"[2]
> - "remoteproc/davinci: common clock framework related fixes"[3]
>
> [1]: https://patchwork.freedesktop.org/patch/210696/
> [2]: https://lkml.org/lkml/2018/5/9/626
> [3]: https://lkml.org/lkml/2018/5/2/201
>
> You can find a working branch with everything included (plus a few extras, like
> cpufreq-dt) in the "common-clk-v10" branch of https://github.com/dlech/ev3dev-kernel.git.
>
>
> Testing/debugging for the uninitiated:
>
> I only have one device to test with, which is based on da850, so I will
> have to rely on others to do some testing here. Since we are dealing with
> clocks, if something isn't working, you most likely won't see output on
> the serial port. To figure out what is going on, you need to enable...
>
> CONFIG_DEBUG_LL=y
> CONFIG_EARLY_PRINTK=y
>
> and add "earlyprintk clk_ignore_unused" to the kernel command line options.
> You may need to select a different UART for this depending on your board. I
> think UART1 is the default in the kernel configuration.
>
> On da850 devices comment out the lines:
>
> /* pll1_sysclk2 is not affected by CPU scaling, so use it for async3 */
> parent = clk_hw_get_parent_by_index(&mux->hw, 1);
> if (parent)
> clk_set_parent(mux->hw.clk, parent->clk);
> else
> dev_warn(dev, "Failed to find async3 parent clock\n");
>
> in da8xx-cfgchip.c or, if using device tree, comment out the lines:
>
> assigned-clocks = <&async3_clk>;
> assigned-clock-parents = <&pll1_sysclk 2>;
>
> in da850.dtsi when doing earlyprintk, otherwise the UART1 and UART2 clock
> source will change during boot and cause garbled output after a point.
>
>
> David Lechner (27):
> clk: davinci: pll: allow dev == NULL
> clk: davinci: da850-pll: change PLL0 to CLK_OF_DECLARE
> clk: davinci: psc: allow for dev == NULL
> ARM: davinci: pass clock as parameter to davinci_timer_init()
> ARM: davinci: da830: add new clock init using common clock framework
> ARM: davinci: da850: add new clock init using common clock framework
> ARM: davinci: dm355: add new clock init using common clock framework
> ARM: davinci: dm365: add new clock init using common clock framework
> ARM: davinci: dm644x: add new clock init using common clock framework
> ARM: davinci: dm646x: add new clock init using common clock framework
> ARM: davinci: da8xx: add new USB PHY clock init using common clock
> framework
> ARM: davinci: da8xx: add new sata_refclk init using common clock
> framework
> ARM: davinci: remove CONFIG_DAVINCI_RESET_CLOCKS
> ARM: davinci_all_defconfig: remove CONFIG_DAVINCI_RESET_CLOCKS
> ARM: davinci: switch to common clock framework
> ARM: davinci: da830: Remove legacy clock init
> ARM: davinci: da850: Remove legacy clock init
> ARM: davinci: dm355: Remove legacy clock init
> ARM: davinci: dm365: Remove legacy clock init
> ARM: davinci: dm644x: Remove legacy clock init
> ARM: davinci: dm646x: Remove legacy clock init
> ARM: davinci: da8xx: Remove legacy USB and SATA clock init
> ARM: davinci: remove legacy clocks
> dt-bindings: timer: new bindings for TI DaVinci timer
> ARM: davinci: add device tree support to timer
> ARM: davinci: da8xx-dt: switch to device tree clocks
> ARM: dts: da850: Add clocks
>
> .../bindings/timer/ti,davinci-timer.txt | 37 +
> arch/arm/Kconfig | 5 +-
> arch/arm/boot/dts/da850-enbw-cmc.dts | 4 +
> arch/arm/boot/dts/da850-evm.dts | 4 +
> arch/arm/boot/dts/da850-lcdk.dts | 9 +
> arch/arm/boot/dts/da850-lego-ev3.dts | 4 +
> arch/arm/boot/dts/da850.dtsi | 168 ++++
> arch/arm/configs/davinci_all_defconfig | 1 -
> arch/arm/mach-davinci/Kconfig | 13 +-
> arch/arm/mach-davinci/Makefile | 4 +-
> arch/arm/mach-davinci/board-da830-evm.c | 12 +-
> arch/arm/mach-davinci/board-da850-evm.c | 2 +
> arch/arm/mach-davinci/board-dm355-evm.c | 2 +
> arch/arm/mach-davinci/board-dm355-leopard.c | 2 +
> arch/arm/mach-davinci/board-dm365-evm.c | 2 +
> arch/arm/mach-davinci/board-dm644x-evm.c | 2 +
> arch/arm/mach-davinci/board-dm646x-evm.c | 2 +
> arch/arm/mach-davinci/board-mityomapl138.c | 2 +
> arch/arm/mach-davinci/board-neuros-osd2.c | 2 +
> arch/arm/mach-davinci/board-omapl138-hawk.c | 11 +-
> arch/arm/mach-davinci/board-sffsdr.c | 2 +
> arch/arm/mach-davinci/clock.c | 745 -----------------
> arch/arm/mach-davinci/clock.h | 76 --
> arch/arm/mach-davinci/common.c | 3 -
> arch/arm/mach-davinci/da830.c | 462 ++---------
> arch/arm/mach-davinci/da850.c | 778 +++---------------
> arch/arm/mach-davinci/da8xx-dt.c | 66 --
> arch/arm/mach-davinci/davinci.h | 8 +
> arch/arm/mach-davinci/devices-da8xx.c | 43 +-
> arch/arm/mach-davinci/devices.c | 1 -
> arch/arm/mach-davinci/dm355.c | 406 ++-------
> arch/arm/mach-davinci/dm365.c | 485 +----------
> arch/arm/mach-davinci/dm644x.c | 344 +-------
> arch/arm/mach-davinci/dm646x.c | 372 +--------
> arch/arm/mach-davinci/include/mach/clock.h | 3 -
> arch/arm/mach-davinci/include/mach/common.h | 11 +-
> arch/arm/mach-davinci/include/mach/da8xx.h | 6 +-
> arch/arm/mach-davinci/pm_domain.c | 5 +
> arch/arm/mach-davinci/psc.c | 137 ---
> arch/arm/mach-davinci/psc.h | 12 -
> arch/arm/mach-davinci/time.c | 39 +-
> arch/arm/mach-davinci/usb-da8xx.c | 242 +-----
> drivers/clk/davinci/pll-da830.c | 4 +-
> drivers/clk/davinci/pll-da850.c | 36 +-
> drivers/clk/davinci/pll-dm355.c | 8 +-
> drivers/clk/davinci/pll-dm365.c | 8 +-
> drivers/clk/davinci/pll-dm644x.c | 8 +-
> drivers/clk/davinci/pll-dm646x.c | 8 +-
> drivers/clk/davinci/pll.c | 110 +--
> drivers/clk/davinci/pll.h | 30 +-
> drivers/clk/davinci/psc-dm355.c | 2 +-
> drivers/clk/davinci/psc-dm365.c | 2 +-
> drivers/clk/davinci/psc-dm644x.c | 2 +-
> drivers/clk/davinci/psc-dm646x.c | 2 +-
> drivers/clk/davinci/psc.c | 27 +-
> include/linux/clk/davinci.h | 29 +
> 56 files changed, 860 insertions(+), 3950 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/timer/ti,davinci-timer.txt
> delete mode 100644 arch/arm/mach-davinci/clock.c
> delete mode 100644 arch/arm/mach-davinci/psc.c
> create mode 100644 include/linux/clk/davinci.h
>
> --
> 2.17.0
>
Powered by blists - more mailing lists