| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20180517082939.14598-7-antoine.tenart@bootlin.com>
Date: Thu, 17 May 2018 10:29:35 +0200
From: Antoine Tenart <antoine.tenart@...tlin.com>
To: davem@...emloft.net, kishon@...com, linux@...linux.org.uk,
gregory.clement@...tlin.com, andrew@...n.ch, jason@...edaemon.net,
sebastian.hesselbarth@...il.com
Cc: Antoine Tenart <antoine.tenart@...tlin.com>,
netdev@...r.kernel.org, linux-kernel@...r.kernel.org,
thomas.petazzoni@...tlin.com, maxime.chevallier@...tlin.com,
miquel.raynal@...tlin.com, nadavh@...vell.com, stefanc@...vell.com,
ymarkman@...vell.com, mw@...ihalf.com,
linux-arm-kernel@...ts.infradead.org
Subject: [PATCH net-next v3 06/10] net: mvpp2: 2500baseX support
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@...tlin.com>
---
drivers/net/ethernet/marvell/mvpp2.c | 51 +++++++++++++++++++++-------
1 file changed, 39 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index ece61f1727e4..5e580482769e 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4871,6 +4871,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
break;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4909,7 +4910,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4940,7 +4942,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4953,7 +4956,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4968,6 +4972,16 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
mvpp22_gop_unmask_irq(port);
}
+/* Sets the PHY mode of the COMPHY (which configures the serdes lanes).
+ *
+ * The PHY mode used by the PPv2 driver comes from the network subsystem, while
+ * the one given to the COMPHY comes from the generic PHY subsystem. Hence they
+ * differ.
+ *
+ * The COMPHY configures the serdes lanes regardless of the actual use of the
+ * lanes by the physical layer. This is why configurations like
+ * "PPv2 (2500BaseX) - COMPHY (2500SGMII)" are valid.
+ */
static int mvpp22_comphy_init(struct mvpp2_port *port)
{
enum phy_mode mode;
@@ -4981,6 +4995,9 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ mode = PHY_MODE_2500SGMII;
+ break;
case PHY_INTERFACE_MODE_10GKR:
mode = PHY_MODE_10GKR;
break;
@@ -5062,7 +5079,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port,
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6273,7 +6291,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
@@ -8056,8 +8075,10 @@ static void mvpp2_phylink_validate(struct net_device *dev,
phylink_set(mask, 10000baseT_Full);
/* Fall-through */
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
+ phylink_set(mask, 2500baseX_Full);
}
bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
@@ -8100,6 +8121,9 @@ static void mvpp2_gmac_link_state(struct mvpp2_port *port,
case PHY_INTERFACE_MODE_1000BASEX:
state->speed = SPEED_1000;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ state->speed = SPEED_2500;
+ break;
default:
if (val & MVPP2_GMAC_STATUS0_GMII_SPEED)
state->speed = SPEED_1000;
@@ -8199,11 +8223,12 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
ctrl2 &= ~(MVPP2_GMAC_PORT_RESET_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
- if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
- /* 1000BaseX port cannot negotiate speed nor can it negotiate
- * duplex: they are always operating with a fixed speed of
- * 1000Mbps in full duplex, so force 1000 speed and full duplex
- * here.
+ if (state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX) {
+ /* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
+ * they negotiate duplex: they are always operating with a fixed
+ * speed of 1000/2500Mbps in full duplex, so force 1000/2500
+ * speed and full duplex here.
*/
ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
an |= MVPP2_GMAC_CONFIG_GMII_SPEED |
@@ -8220,7 +8245,8 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
an |= MVPP2_GMAC_FC_ADV_ASM_EN;
if (state->interface == PHY_INTERFACE_MODE_SGMII ||
- state->interface == PHY_INTERFACE_MODE_1000BASEX) {
+ state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX) {
an |= MVPP2_GMAC_IN_BAND_AUTONEG;
ctrl2 |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -8286,7 +8312,8 @@ static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
mvpp2_xlg_config(port, mode, state);
else if (phy_interface_mode_is_rgmii(state->interface) ||
state->interface == PHY_INTERFACE_MODE_SGMII ||
- state->interface == PHY_INTERFACE_MODE_1000BASEX)
+ state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX)
mvpp2_gmac_config(port, mode, state);
if (port->priv->hw_version == MVPP21 && port->flags & MVPP2_F_LOOPBACK)
--
2.17.0
Powered by blists - more mailing lists