Message-ID: <CAKTKpr7dk4h7ZM+7fBV_CSVknV0+EnAgE2t2b4dDiycdOm1U3w@mail.gmail.com>
Date:   Fri, 18 May 2018 16:27:58 +0530
From:   Ganapatrao Kulkarni <gklkml16@...il.com>
To:     John Garry <john.garry@...wei.com>
Cc:     Ganapatrao Kulkarni <ganapatrao.kulkarni@...ium.com>,
        "linux-doc@...r.kernel.org" <linux-doc@...r.kernel.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>,
        "mark.rutland@....com" <mark.rutland@....com>,
        "Vadim.Lomovtsev@...ium.com" <Vadim.Lomovtsev@...ium.com>,
        "Jan.Glauber@...ium.com" <Jan.Glauber@...ium.com>,
        "Will.Deacon@....com" <Will.Deacon@....com>,
        "Robert.Richter@...ium.com" <Robert.Richter@...ium.com>,
        "jnair@...iumnetworks.com" <jnair@...iumnetworks.com>
Subject: Re: [PATCH v5 2/2] ThunderX2: Add Cavium ThunderX2 SoC UNCORE PMU driver

On Thu, May 17, 2018 at 4:42 PM, John Garry <john.garry@...wei.com> wrote:
> On 16/05/2018 05:55, Ganapatrao Kulkarni wrote:
>>
>> This patch adds a perf driver for the PMU UNCORE devices DDR4 Memory
>> Controller(DMC) and Level 3 Cache(L3C).
>>
>
> Hi,
>
> Just some coding comments below:
>
>> ThunderX2 has 8 independent DMC PMUs to capture performance events
>> corresponding to 8 channels of DDR4 Memory Controller and 16 independent
>> L3C PMUs to capture events corresponding to 16 tiles of L3 cache.
>> Each PMU supports up to 4 counters. All counters lack overflow interrupt
>> and are sampled periodically.
>>
>> Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@...ium.com>
>> ---
>>  drivers/perf/Kconfig         |   8 +
>>  drivers/perf/Makefile        |   1 +
>>  drivers/perf/thunderx2_pmu.c | 965
>> +++++++++++++++++++++++++++++++++++++++++++
>>  include/linux/cpuhotplug.h   |   1 +
>>  4 files changed, 975 insertions(+)
>>  create mode 100644 drivers/perf/thunderx2_pmu.c
>>
>> diff --git a/drivers/perf/Kconfig b/drivers/perf/Kconfig
>> index 28bb5a0..eafd0fc 100644
>> --- a/drivers/perf/Kconfig
>> +++ b/drivers/perf/Kconfig
>> @@ -85,6 +85,14 @@ config QCOM_L3_PMU
>>            Adds the L3 cache PMU into the perf events subsystem for
>>            monitoring L3 cache events.
>>
>> +config THUNDERX2_PMU
>> +        bool "Cavium ThunderX2 SoC PMU UNCORE"
>> +        depends on ARCH_THUNDER2 && PERF_EVENTS && ACPI
>
>
> Is the explicit dependency for PERF_EVENTS required, since we're under the
> PERF_EVENTS menu?

not really, i can drop this.
>
> And IIRC for other perf drivers we required a dependency on ARM64 - is that
> required here also? I see arm_smccc_smc() calls in the code...

ok.
>
>
>> +       help
>> +         Provides support for ThunderX2 UNCORE events.
>> +         The SoC has PMU support in its L3 cache controller (L3C) and
>> +         in the DDR4 Memory Controller (DMC).
>> +
>>  config XGENE_PMU
>>          depends on ARCH_XGENE
>>          bool "APM X-Gene SoC PMU"
>> diff --git a/drivers/perf/Makefile b/drivers/perf/Makefile
>> index b3902bd..909f27f 100644
>> --- a/drivers/perf/Makefile
>> +++ b/drivers/perf/Makefile
>> @@ -7,5 +7,6 @@ obj-$(CONFIG_ARM_PMU_ACPI) += arm_pmu_acpi.o
>>  obj-$(CONFIG_HISI_PMU) += hisilicon/
>>  obj-$(CONFIG_QCOM_L2_PMU)      += qcom_l2_pmu.o
>>  obj-$(CONFIG_QCOM_L3_PMU) += qcom_l3_pmu.o
>> +obj-$(CONFIG_THUNDERX2_PMU) += thunderx2_pmu.o
>>  obj-$(CONFIG_XGENE_PMU) += xgene_pmu.o
>>  obj-$(CONFIG_ARM_SPE_PMU) += arm_spe_pmu.o
>> diff --git a/drivers/perf/thunderx2_pmu.c b/drivers/perf/thunderx2_pmu.c
>> new file mode 100644
>> index 0000000..0401443
>> --- /dev/null
>> +++ b/drivers/perf/thunderx2_pmu.c
>> @@ -0,0 +1,965 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * CAVIUM THUNDERX2 SoC PMU UNCORE
>> + *
>> + * Copyright (C) 2018 Cavium Inc.
>> + * Author: Ganapatrao Kulkarni <gkulkarni@...ium.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program.  If not, see <http://www.gnu.org/licenses/>.
>> + */
>
>
> Isn't this the same as the SPDX?

ok, i will remove it.
>
>> +
>> +#include <linux/acpi.h>
>> +#include <linux/arm-smccc.h>
>> +#include <linux/cpuhotplug.h>
>> +#include <linux/perf_event.h>
>> +#include <linux/platform_device.h>
>> +
>> +/* L3c and DMC has 16 and 8 channels per socket respectively.
>
>
> L3C, right?

ok
>
>> + * Each Channel supports UNCORE PMU device and consists of
>> + * 4 independent programmable counters. Counters are 32 bit
>> + * and does not support overflow interrupt, they needs to be
>
>
> /s/needs/need/, /s/does/do/

ok
>
>> + * sampled before overflow(i.e, at every 2 seconds).
>
>
> how can you ensure that this value is low enough?
>
> "I saw this comment in previous patch:
>> Given that all channels compete for access to the muxed register
>> interface, I suspect we need to try more often than once every 2
>> seconds...
>
> 2 seconds seems to be sufficient. So far testing looks good."
>
> Can you provide any more analytical reasoning than this?
>
>> + */
>> +
>> +#define UNCORE_MAX_COUNTERS            4
>> +#define UNCORE_L3_MAX_TILES            16
>> +#define UNCORE_DMC_MAX_CHANNELS                8
>> +
>> +#define UNCORE_HRTIMER_INTERVAL                (2 * NSEC_PER_SEC)
>> +#define GET_EVENTID(ev)                        ((ev->hw.config) & 0x1ff)
>> +#define GET_COUNTERID(ev)              ((ev->hw.idx) & 0xf)
>> +#define GET_CHANNELID(pmu_uncore)      (pmu_uncore->channel)
>> +#define DMC_EVENT_CFG(idx, val)                ((val) << (((idx) * 8) +
>> 1))
>> +
>> +#define DMC_COUNTER_CTL                        0x234
>> +#define DMC_COUNTER_DATA               0x240
>> +#define L3C_COUNTER_CTL                        0xA8
>> +#define L3C_COUNTER_DATA               0xAC
>
>
> I feel it's generally better to keep register offsets in numeric order (if
> indeed, that is what they are)

ok.
>
>
>> +
>> +#define THUNDERX2_SMC_CALL_ID          0xC200FF00
>> +#define THUNDERX2_SMC_SET_CHANNEL      0xB010
>> +
>> +enum thunderx2_uncore_l3_events {
>> +       L3_EVENT_NONE,
>> +       L3_EVENT_NBU_CANCEL,
>> +       L3_EVENT_DIB_RETRY,
>> +       L3_EVENT_DOB_RETRY,
>> +       L3_EVENT_DIB_CREDIT_RETRY,
>> +       L3_EVENT_DOB_CREDIT_RETRY,
>> +       L3_EVENT_FORCE_RETRY,
>> +       L3_EVENT_IDX_CONFLICT_RETRY,
>> +       L3_EVENT_EVICT_CONFLICT_RETRY,
>> +       L3_EVENT_BANK_CONFLICT_RETRY,
>> +       L3_EVENT_FILL_ENTRY_RETRY,
>> +       L3_EVENT_EVICT_NOT_READY_RETRY,
>> +       L3_EVENT_L3_RETRY,
>> +       L3_EVENT_READ_REQ,
>> +       L3_EVENT_WRITE_BACK_REQ,
>> +       L3_EVENT_INVALIDATE_NWRITE_REQ,
>> +       L3_EVENT_INV_REQ,
>> +       L3_EVENT_SELF_REQ,
>> +       L3_EVENT_REQ,
>> +       L3_EVENT_EVICT_REQ,
>> +       L3_EVENT_INVALIDATE_NWRITE_HIT,
>> +       L3_EVENT_INVALIDATE_HIT,
>> +       L3_EVENT_SELF_HIT,
>> +       L3_EVENT_READ_HIT,
>> +       L3_EVENT_MAX,
>
>
> ',' required?

not really; however, having this will help in moving around without
worring about adding it.
>
>> +};
>> +
>> +enum thunderx2_uncore_dmc_events {
>> +       DMC_EVENT_NONE,
>> +       DMC_EVENT_COUNT_CYCLES,
>> +       DMC_EVENT_RES2,
>> +       DMC_EVENT_RES3,
>> +       DMC_EVENT_RES4,
>> +       DMC_EVENT_RES5,
>> +       DMC_EVENT_RES6,
>> +       DMC_EVENT_RES7,
>> +       DMC_EVENT_RES8,
>> +       DMC_EVENT_READ_64B_TXNS,
>> +       DMC_EVENT_READ_BELOW_64B_TXNS,
>> +       DMC_EVENT_WRITE_TXNS,
>> +       DMC_EVENT_TXN_CYCLES,
>> +       DMC_EVENT_DATA_TRANSFERS,
>> +       DMC_EVENT_CANCELLED_READ_TXNS,
>> +       DMC_EVENT_CONSUMED_READ_TXNS,
>> +       DMC_EVENT_MAX,
>
>
> ditto
>
>> +};
>> +
>> +enum thunderx2_uncore_type {
>> +       PMU_TYPE_L3C,
>> +       PMU_TYPE_DMC,
>> +       PMU_TYPE_INVALID,
>> +};
>> +
>> +/*
>> + * pmu on each socket has 2 uncore devices(dmc and l3),
>> + * each uncore device has up to 16 channels, each channel can sample
>> + * events independently with counters up to 4.
>> + *
>> + * struct thunderx2_pmu_uncore_channel created per channel.
>> + * struct thunderx2_pmu_uncore_dev per uncore device.
>
>
> this comment is a bit obvious

ok.
>
>
>> + */
>> +struct thunderx2_pmu_uncore_channel {
>> +       struct pmu pmu;
>> +       struct hlist_node       node;
>> +       struct thunderx2_pmu_uncore_dev *uncore_dev;
>> +       int channel;
>> +       int cpu;
>> +       DECLARE_BITMAP(active_counters, UNCORE_MAX_COUNTERS);
>> +       struct perf_event *events[UNCORE_MAX_COUNTERS];
>> +       struct hrtimer hrtimer;
>> +       /* to sync counter alloc/release */
>> +       raw_spinlock_t lock;
>> +};
>> +
>> +struct thunderx2_pmu_uncore_dev {
>> +       char *name;
>> +       struct device *dev;
>> +       enum thunderx2_uncore_type type;
>> +       void __iomem *base;
>> +       int node;
>> +       u32    max_counters;
>> +       u32    max_channels;
>> +       u32    max_events;
>> +       u64 hrtimer_interval;
>> +       /* this lock synchronizes across channels */
>> +       raw_spinlock_t lock;
>> +       const struct attribute_group **attr_groups;
>> +       void    (*init_cntr_base)(struct perf_event *event,
>> +                       struct thunderx2_pmu_uncore_dev *uncore_dev);
>> +       void    (*select_channel)(struct perf_event *event);
>> +       void    (*stop_event)(struct perf_event *event);
>> +       void    (*start_event)(struct perf_event *event, int flags);
>> +};
>> +
>> +static inline struct thunderx2_pmu_uncore_channel *
>
>
> is inline keyword required or even used generally? Since static, can't the
> compiler figure this out?
>
>> +pmu_to_thunderx2_pmu_uncore(struct pmu *pmu)
>> +{
>> +       return container_of(pmu, struct thunderx2_pmu_uncore_channel,
>> pmu);
>> +}
>> +
>> +/*
>> + * sysfs format attributes
>> + */
>
>
> can't this comment fit on a single line?
>
>
>> +static ssize_t thunderx2_pmu_format_show(struct device *dev,
>> +                                    struct device_attribute *attr, char
>> *buf)
>> +{
>> +       struct dev_ext_attribute *eattr;
>> +
>> +       eattr = container_of(attr, struct dev_ext_attribute, attr);
>> +       return sprintf(buf, "%s\n", (char *) eattr->var);
>> +}
>> +
>> +#define FORMAT_ATTR(_name, _config) \
>> +       (&((struct dev_ext_attribute[]) { \
>> +          { \
>> +          .attr = __ATTR(_name, 0444, thunderx2_pmu_format_show, NULL), \
>> +          .var = (void *) _config, \
>> +          } \
>> +       })[0].attr.attr)
>> +
>> +static struct attribute *l3c_pmu_format_attrs[] = {
>> +       FORMAT_ATTR(event,      "config:0-4"),
>> +       NULL,
>> +};
>> +
>> +static struct attribute *dmc_pmu_format_attrs[] = {
>> +       FORMAT_ATTR(event,      "config:0-4"),
>> +       NULL,
>> +};
>> +
>> +static const struct attribute_group l3c_pmu_format_attr_group = {
>> +       .name = "format",
>> +       .attrs = l3c_pmu_format_attrs,
>> +};
>> +
>> +static const struct attribute_group dmc_pmu_format_attr_group = {
>> +       .name = "format",
>> +       .attrs = dmc_pmu_format_attrs,
>> +};
>> +
>
>
> [ ... ]
>
>
>> + * Per PMU device attribute groups
>> + */
>> +static const struct attribute_group *l3c_pmu_attr_groups[] = {
>> +       &l3c_pmu_format_attr_group,
>> +       &pmu_cpumask_attr_group,
>> +       &l3c_pmu_events_attr_group,
>> +       NULL
>> +};
>> +
>> +static const struct attribute_group *dmc_pmu_attr_groups[] = {
>> +       &dmc_pmu_format_attr_group,
>> +       &pmu_cpumask_attr_group,
>> +       &dmc_pmu_events_attr_group,
>> +       NULL
>> +};
>> +
>> +static inline u32 reg_readl(unsigned long addr)
>> +{
>> +       return readl((void __iomem *)addr);
>> +}
>> +
>> +static inline void reg_writel(u32 val, unsigned long addr)
>> +{
>> +       writel(val, (void __iomem *)addr);
>> +}
>> +
>> +static int alloc_counter(struct thunderx2_pmu_uncore_channel *pmu_uncore)
>> +{
>> +       int counter;
>> +
>> +       raw_spin_lock(&pmu_uncore->lock);
>> +       counter = find_first_zero_bit(pmu_uncore->active_counters,
>> +                               pmu_uncore->uncore_dev->max_counters);
>> +       if (counter == pmu_uncore->uncore_dev->max_counters) {
>> +               raw_spin_unlock(&pmu_uncore->lock);
>> +               return -ENOSPC;
>> +       }
>> +       set_bit(counter, pmu_uncore->active_counters);
>> +       raw_spin_unlock(&pmu_uncore->lock);
>> +       return counter;
>> +}
>> +
>> +static void free_counter(
>> +               struct thunderx2_pmu_uncore_channel *pmu_uncore, int
>> counter)
>
>
> strange formatting

it is to fit in 80 char line.
>
>> +{
>> +       raw_spin_lock(&pmu_uncore->lock);
>> +       clear_bit(counter, pmu_uncore->active_counters);
>> +       raw_spin_unlock(&pmu_uncore->lock);
>> +}
>> +
>
>
> [ ... ]
>
>
>> +static void uncore_stop_event_l3c(struct perf_event *event)
>> +{
>> +       reg_writel(0, event->hw.config_base);
>> +}
>> +
>> +static void uncore_start_event_dmc(struct perf_event *event, int flags)
>> +{
>> +       u32 val;
>> +       struct hw_perf_event *hwc = &event->hw;
>> +       int idx = GET_COUNTERID(event);
>> +       int event_type = GET_EVENTID(event);
>> +
>> +       /* enable and start counters.
>> +        * 8 bits for each counter, bits[05:01] of a counter to set event
>> type.
>> +        */
>> +       val = reg_readl(hwc->config_base);
>> +       val &= ~DMC_EVENT_CFG(idx, 0x1f);
>> +       val |= DMC_EVENT_CFG(idx, event_type);
>> +       reg_writel(val, hwc->config_base);
>> +       local64_set(&hwc->prev_count, 0);
>> +       reg_writel(0, hwc->event_base);
>> +}
>> +
>> +static void uncore_stop_event_dmc(struct perf_event *event)
>> +{
>> +       u32 val;
>> +       struct hw_perf_event *hwc = &event->hw;
>> +       int idx = GET_COUNTERID(event);
>> +
>> +       /* clear event type(bits[05:01]) to stop counter */
>> +       val = reg_readl(hwc->config_base);
>> +       val &= ~DMC_EVENT_CFG(idx, 0x1f);
>> +       reg_writel(val, hwc->config_base);
>> +}
>> +
>> +static void init_cntr_base_l3c(struct perf_event *event,
>> +               struct thunderx2_pmu_uncore_dev *uncore_dev)
>> +{
>> +       struct hw_perf_event *hwc = &event->hw;
>> +
>> +       /* counter ctrl/data reg offset at 8 */
>> +       hwc->config_base = (unsigned long)uncore_dev->base
>> +               + L3C_COUNTER_CTL + (8 * GET_COUNTERID(event));
>> +       hwc->event_base =  (unsigned long)uncore_dev->base
>> +               + L3C_COUNTER_DATA + (8 * GET_COUNTERID(event));
>
>
> Is there a better way to hold this, since we're casting back to a void *
> when writing to the register?
>

dont think so.
>
>> +}
>> +
>> +static void init_cntr_base_dmc(struct perf_event *event,
>> +               struct thunderx2_pmu_uncore_dev *uncore_dev)
>> +{
>> +       struct hw_perf_event *hwc = &event->hw;
>> +
>> +       hwc->config_base = (unsigned long)uncore_dev->base
>> +               + DMC_COUNTER_CTL;
>> +       /* counter data reg offset at 0xc */
>> +       hwc->event_base = (unsigned long)uncore_dev->base
>> +               + DMC_COUNTER_DATA + (0xc * GET_COUNTERID(event));
>> +}
>> +
>> +static void thunderx2_uncore_update(struct perf_event *event)
>> +{
>> +       s64 prev, new = 0;
>> +       u64 delta;
>> +       struct hw_perf_event *hwc = &event->hw;
>> +       struct thunderx2_pmu_uncore_channel *pmu_uncore;
>> +       enum thunderx2_uncore_type type;
>> +
>> +       pmu_uncore = pmu_to_thunderx2_pmu_uncore(event->pmu);
>> +       type = pmu_uncore->uncore_dev->type;
>> +
>> +       pmu_uncore->uncore_dev->select_channel(event);
>> +
>> +       new = reg_readl(hwc->event_base);
>> +       prev = local64_xchg(&hwc->prev_count, new);
>> +
>> +       /* handles rollover of 32 bit counter */
>> +       delta = (u32)(((1UL << 32) - prev) + new);
>> +       local64_add(delta, &event->count);
>> +}
>> +
>> +enum thunderx2_uncore_type get_uncore_device_type(struct acpi_device
>> *adev)
>> +{
>> +       int i = 0;
>> +       struct acpi_uncore_device {
>> +               __u8 id[ACPI_ID_LEN];
>> +               enum thunderx2_uncore_type type;
>> +       } devices[] = {
>> +               {"CAV901D", PMU_TYPE_L3C},
>> +               {"CAV901F", PMU_TYPE_DMC},
>> +               {"", PMU_TYPE_INVALID},
>
>
>
> for sentinels, ',' should not be required

ok, i will remove.
>
>> +       };
>> +
>> +       while (devices[i].type != PMU_TYPE_INVALID) {
>> +               if (!strcmp(acpi_device_hid(adev), devices[i].id))
>> +                       return devices[i].type;
>
>
> Can't you use acpi_match_device()?

alredy i have acpi device id, just i have to compare to find type.
acpi_match_device is unnecessary which goes in loop over all device ids/names.

>
>> +               i++;
>> +       }
>> +       return PMU_TYPE_INVALID;
>> +}
>> +
>> +/*
>> + * We must NOT create groups containing events from multiple hardware
>> PMUs,
>> + * although mixing different software and hardware PMUs is allowed.
>> + */
>> +static bool thunderx2_uncore_validate_event_group(struct perf_event
>> *event)
>
>
> [ ... ]
>
>
>> +
>> +static int thunderx2_pmu_uncore_add(struct thunderx2_pmu_uncore_dev
>> *uncore_dev,
>> +               int channel)
>> +{
>> +       struct thunderx2_pmu_uncore_channel *pmu_uncore;
>> +       int ret, cpu;
>> +
>> +       pmu_uncore = devm_kzalloc(uncore_dev->dev, sizeof(*pmu_uncore),
>> +                       GFP_KERNEL);
>> +       if (!pmu_uncore)
>> +               return -ENOMEM;
>> +
>> +       cpu = cpumask_any_and(cpumask_of_node(uncore_dev->node),
>> +                       cpu_online_mask);
>> +       if (cpu >= nr_cpu_ids)
>> +               return -EINVAL;
>> +
>> +       pmu_uncore->cpu = cpu;
>> +       pmu_uncore->channel = channel;
>> +       pmu_uncore->uncore_dev = uncore_dev;
>> +
>> +       hrtimer_init(&pmu_uncore->hrtimer, CLOCK_MONOTONIC,
>> HRTIMER_MODE_REL);
>> +       pmu_uncore->hrtimer.function = thunderx2_uncore_hrtimer_callback;
>> +
>> +       ret = thunderx2_pmu_uncore_register(pmu_uncore);
>> +       if (ret) {
>> +               dev_err(uncore_dev->dev, "%s PMU: Failed to init
>> driver\n",
>> +                               uncore_dev->name);
>> +               return -ENODEV;
>> +       }
>> +
>> +       /* register hotplug callback for the pmu */
>> +       ret = cpuhp_state_add_instance(
>> +                       CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
>> +                       &pmu_uncore->node);
>> +       if (ret) {
>> +               dev_err(uncore_dev->dev, "Error %d registering hotplug",
>> ret);
>> +               return ret;
>> +       }
>> +
>> +       dev_dbg(uncore_dev->dev, "%s PMU UNCORE registered\n",
>> +                       pmu_uncore->pmu.name);
>
>
> strange alignment, and many more times in the code

same as said above.

>
>
>> +       return ret;
>> +}
>> +
>> +static struct thunderx2_pmu_uncore_dev *init_pmu_uncore_dev(
>> +               struct device *dev, acpi_handle handle,
>> +               struct acpi_device *adev, u32 type)
>> +{
>> +       struct thunderx2_pmu_uncore_dev *uncore_dev;
>> +       void __iomem *base;
>> +       struct resource res;
>> +       struct resource_entry *rentry;
>> +       struct list_head list;
>> +       int ret;
>> +
>> +       INIT_LIST_HEAD(&list);
>> +       ret = acpi_dev_get_resources(adev, &list, NULL, NULL);
>> +       if (ret <= 0) {
>> +               dev_err(dev, "failed to parse _CRS method, error %d\n",
>> ret);
>> +               return NULL;
>> +       }
>> +
>> +       list_for_each_entry(rentry, &list, node) {
>> +               if (resource_type(rentry->res) == IORESOURCE_MEM) {
>> +                       res = *rentry->res;
>> +                       break;
>> +               }
>> +       }
>
>
> what I am missing that you can not use
> platform_get_resource(,IORESOURCE_MEM,)?

i have uncore device per socket defined in acpi table and inturn each
device has 2 sub devices(l3c and dmc)
>
>
> And I also wonder if you need all the device-related arguments for the code
>
>> +
>> +       if (!rentry->res)
>> +               return NULL;
>> +
>> +       acpi_dev_free_resource_list(&list);
>> +       base = devm_ioremap_resource(dev, &res);
>> +       if (IS_ERR(base)) {
>> +               dev_err(dev, "PMU type %d: Fail to map resource\n", type);
>> +               return NULL;
>> +       }
>> +
>> +       uncore_dev = devm_kzalloc(dev, sizeof(*uncore_dev), GFP_KERNEL);
>> +       if (!uncore_dev)
>> +               return NULL;
>> +
>> +       uncore_dev->dev = dev;
>> +       uncore_dev->type = type;
>> +       uncore_dev->base = base;
>> +       uncore_dev->node = dev_to_node(dev);
>> +
>> +       raw_spin_lock_init(&uncore_dev->lock);
>> +
>> +       switch (uncore_dev->type) {
>
>
> if we can re-arrange, isn't it better to do the steps which can fail before
> the steps which can't?
>
>> +       case PMU_TYPE_L3C:
>> +               uncore_dev->max_counters = UNCORE_MAX_COUNTERS;
>> +               uncore_dev->max_channels = UNCORE_L3_MAX_TILES;
>> +               uncore_dev->max_events = L3_EVENT_MAX;
>> +               uncore_dev->hrtimer_interval = UNCORE_HRTIMER_INTERVAL;
>> +               uncore_dev->attr_groups = l3c_pmu_attr_groups;
>> +               uncore_dev->name = devm_kasprintf(dev, GFP_KERNEL,
>> +                               "uncore_l3c_%d", uncore_dev->node);
>> +               uncore_dev->init_cntr_base = init_cntr_base_l3c;
>> +               uncore_dev->start_event = uncore_start_event_l3c;
>> +               uncore_dev->stop_event = uncore_stop_event_l3c;
>> +               uncore_dev->select_channel = uncore_select_channel;
>
>
> it's possible to bring the common code outside the swicth statement, but
> probably not worth it
>
>> +               break;
>> +       case PMU_TYPE_DMC:
>> +               uncore_dev->max_counters = UNCORE_MAX_COUNTERS;
>> +               uncore_dev->max_channels = UNCORE_DMC_MAX_CHANNELS;
>> +               uncore_dev->max_events = DMC_EVENT_MAX;
>> +               uncore_dev->hrtimer_interval = UNCORE_HRTIMER_INTERVAL;
>> +               uncore_dev->attr_groups = dmc_pmu_attr_groups;
>> +               uncore_dev->name = devm_kasprintf(dev, GFP_KERNEL,
>> +                               "uncore_dmc_%d", uncore_dev->node);
>> +               uncore_dev->init_cntr_base = init_cntr_base_dmc;
>> +               uncore_dev->start_event = uncore_start_event_dmc;
>> +               uncore_dev->stop_event = uncore_stop_event_dmc;
>> +               uncore_dev->select_channel = uncore_select_channel;
>> +               break;
>> +       case PMU_TYPE_INVALID:
>> +               devm_kfree(dev, uncore_dev);
>
>
> do you really need this?

yes, in case corrupted table.
>
>> +               uncore_dev = NULL;
>> +               break;
>
>
> return NULL
>
> And don't we require a default statement?
>
>> +       }
>> +
>> +       return uncore_dev;
>> +}
>> +
>> +static acpi_status thunderx2_pmu_uncore_dev_add(acpi_handle handle, u32
>> level,
>> +                                   void *data, void **return_value)
>> +{
>> +       struct thunderx2_pmu_uncore_dev *uncore_dev;
>> +       struct acpi_device *adev;
>> +       enum thunderx2_uncore_type type;
>> +       int channel;
>> +
>> +       if (acpi_bus_get_device(handle, &adev))
>> +               return AE_OK;
>> +       if (acpi_bus_get_status(adev) || !adev->status.present)
>> +               return AE_OK;
>> +
>> +       type = get_uncore_device_type(adev);
>> +       if (type == PMU_TYPE_INVALID)
>> +               return AE_OK;
>> +
>> +       uncore_dev = init_pmu_uncore_dev((struct device *)data, handle,
>
>
> no need to cast void *
>
>
>> +                       adev, type);
>> +
>> +       if (!uncore_dev)
>> +               return AE_ERROR;
>> +
>> +       for (channel = 0; channel < uncore_dev->max_channels; channel++) {
>> +               if (thunderx2_pmu_uncore_add(uncore_dev, channel)) {
>> +                       /* Can't add the PMU device, abort */
>> +                       return AE_ERROR;
>> +               }
>> +       }
>> +       return AE_OK;
>> +}
>> +
>> +static int thunderx2_uncore_pmu_offline_cpu(unsigned int cpu,
>> +               struct hlist_node *node)
>> +{
>> +       int new_cpu;
>> +       struct thunderx2_pmu_uncore_channel *pmu_uncore;
>> +
>> +       pmu_uncore = hlist_entry_safe(node,
>> +                       struct thunderx2_pmu_uncore_channel, node);
>> +       if (cpu != pmu_uncore->cpu)
>> +               return 0;
>> +
>> +       new_cpu = cpumask_any_and(
>> +                       cpumask_of_node(pmu_uncore->uncore_dev->node),
>> +                       cpu_online_mask);
>> +       if (new_cpu >= nr_cpu_ids)
>> +               return 0;
>> +
>> +       pmu_uncore->cpu = new_cpu;
>> +       perf_pmu_migrate_context(&pmu_uncore->pmu, cpu, new_cpu);
>> +       return 0;
>> +}
>> +
>> +static const struct acpi_device_id thunderx2_uncore_acpi_match[] = {
>> +       {"CAV901C", 0},
>> +       {},
>
>
> no ',' required

ok
>
>> +};
>> +MODULE_DEVICE_TABLE(acpi, thunderx2_uncore_acpi_match);
>> +
>> +static int thunderx2_uncore_probe(struct platform_device *pdev)
>> +{
>> +       struct device *dev = &pdev->dev;
>> +       acpi_handle handle;
>> +       acpi_status status;
>> +
>> +       set_dev_node(dev, acpi_get_node(ACPI_HANDLE(dev)));
>
>
> Is this already done when the platform device is created in ACPI
> enumeration? I assume the child devices have enumerated at this point.

no
>
>
>> +
>> +       /* Make sure firmware supports DMC/L3C set channel smc call */
>> +       if (test_uncore_select_channel_early(dev))
>> +               return -ENODEV;
>> +
>> +       if (!has_acpi_companion(dev))
>> +               return -ENODEV;
>> +
>> +       handle = ACPI_HANDLE(dev);
>> +       if (!handle)
>> +               return -EINVAL;
>> +
>> +       /* Walk through the tree for all PMU UNCORE devices */
>> +       status = acpi_walk_namespace(ACPI_TYPE_DEVICE, handle, 1,
>> +                                    thunderx2_pmu_uncore_dev_add,
>> +                                    NULL, dev, NULL);
>> +       if (ACPI_FAILURE(status)) {
>> +               dev_err(dev, "failed to probe PMU devices\n");
>> +               return_ACPI_STATUS(status);
>> +       }
>> +
>> +       dev_info(dev, "node%d: pmu uncore registered\n",
>> dev_to_node(dev));
>> +       return 0;
>> +}
>> +
>> +static struct platform_driver thunderx2_uncore_driver = {
>> +       .probe = thunderx2_uncore_probe,
>
>
> why no remove?

this is built in driver.
>
>
>> +       .driver = {
>> +               .name           = "thunderx2-uncore-pmu",
>> +               .acpi_match_table = ACPI_PTR(thunderx2_uncore_acpi_match),
>> +       },
>> +};
>> +
>> +static int __init register_thunderx2_uncore_driver(void)
>> +{
>> +       int ret;
>> +
>> +       ret =
>> cpuhp_setup_state_multi(CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
>> +                                     "perf/tx2/uncore:online",
>> +                                     NULL,
>> +                                     thunderx2_uncore_pmu_offline_cpu);
>> +       if (ret)
>> +               return ret;
>> +
>> +       return platform_driver_register(&thunderx2_uncore_driver);
>> +
>> +}
>> +device_initcall(register_thunderx2_uncore_driver);
>> diff --git a/include/linux/cpuhotplug.h b/include/linux/cpuhotplug.h
>> index 8796ba3..eb0c896 100644
>> --- a/include/linux/cpuhotplug.h
>> +++ b/include/linux/cpuhotplug.h
>> @@ -161,6 +161,7 @@ enum cpuhp_state {
>>         CPUHP_AP_PERF_ARM_L2X0_ONLINE,
>>         CPUHP_AP_PERF_ARM_QCOM_L2_ONLINE,
>>         CPUHP_AP_PERF_ARM_QCOM_L3_ONLINE,
>> +       CPUHP_AP_PERF_ARM_THUNDERX2_UNCORE_ONLINE,
>>         CPUHP_AP_PERF_POWERPC_NEST_IMC_ONLINE,
>>         CPUHP_AP_PERF_POWERPC_CORE_IMC_ONLINE,
>>         CPUHP_AP_PERF_POWERPC_THREAD_IMC_ONLINE,
>>
>
>

thanks
Ganapat

Powered by blists - more mailing lists