| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <705D14B1C7978B40A723277C067CEDE2010A9B5491@IN01WEMBXB.internal.synopsys.com>
Date: Thu, 24 May 2018 11:28:41 +0000
From: Prabu Thangamuthu <Prabu.T@...opsys.com>
To: Adrian Hunter <adrian.hunter@...el.com>,
"ulf.hansson@...aro.org" <ulf.hansson@...aro.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"linux-mmc@...r.kernel.org" <linux-mmc@...r.kernel.org>
CC: Manjunath M Bettegowda <Manjunath.MB@...opsys.com>
Subject: Re: [PATCH 1/1] mmc: sdhci-pci-dwc-mshc: synopsys dwc mshc support
Hi Adrian,
On 5/24/2018 2:06 PM, Adrian Hunter wrote:
> Hi
>
> This patch is mangled.
We will check it.
>
> On 22/05/18 09:42, Prabu Thangamuthu wrote:
>> To enable Synopsys DWC MSHC controller on HPAS-DX platform connected using
>> PCIe interface. As Clock generation logic is implemented in MMCM module of
>> HAPS-DX platform, we have separate functions to control the MMCM to
>> generate required clocks with respect to speed mode. Also we have platform
>> specific set_power function to support different VDD of eMMC devices.
>>
>> Signed-off-by: Prabu Thangamuthu <prabu.t@...opsys.com>
>> ---
>> MAINTAINERS | 7 ++
>> drivers/mmc/host/Makefile | 3 +-
>> drivers/mmc/host/sdhci-pci-core.c | 1 +
>> drivers/mmc/host/sdhci-pci-dwc-mshc.c | 146
>> ++++++++++++++++++++++++++++++++++
>> drivers/mmc/host/sdhci-pci-dwc-mshc.h | 37 +++++++++
>> drivers/mmc/host/sdhci-pci.h | 3 +
>> 6 files changed, 196 insertions(+), 1 deletion(-)
>> create mode 100644 drivers/mmc/host/sdhci-pci-dwc-mshc.c
>> create mode 100644 drivers/mmc/host/sdhci-pci-dwc-mshc.h
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 9051a9c..f1749c4 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12643,6 +12643,13 @@ S: Maintained
>> F: drivers/mmc/host/sdhci*
>> F: include/linux/mmc/sdhci*
>>
>> +SYNOPSYS SDHCI COMPLIANT DWC MSHC DRIVER
>> +M: Prabu Thangamuthu <prabu.t@...opsys.com>
>> +M: Manjunath M B <manjumb@...opsys.com>
>> +L: linux-mmc@...r.kernel.org
>> +S: Maintained
>> +F: drivers/mmc/host/sdhci-pci-dwc-mshc*
>> +
>> SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) SAMSUNG DRIVER
>> M: Ben Dooks <ben-linux@...ff.org>
>> M: Jaehoon Chung <jh80.chung@...sung.com>
>> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
>> index 6aead24..6c0d3fb 100644
>> --- a/drivers/mmc/host/Makefile
>> +++ b/drivers/mmc/host/Makefile
>> @@ -11,7 +11,8 @@ obj-$(CONFIG_MMC_MXC) += mxcmmc.o
>> obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
>> obj-$(CONFIG_MMC_SDHCI) += sdhci.o
>> obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
>> -sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o
>> sdhci-pci-arasan.o
>> +sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o
>> sdhci-pci-arasan.o \
>> + sdhci-pci-dwc-mshc.o
>> obj-$(subst m,y,$(CONFIG_MMC_SDHCI_PCI)) += sdhci-pci-data.o
>> obj-$(CONFIG_MMC_SDHCI_ACPI) += sdhci-acpi.o
>> obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
>> diff --git a/drivers/mmc/host/sdhci-pci-core.c
>> b/drivers/mmc/host/sdhci-pci-core.c
>> index 77dd352..96b6963 100644
>> --- a/drivers/mmc/host/sdhci-pci-core.c
>> +++ b/drivers/mmc/host/sdhci-pci-core.c
>> @@ -1511,6 +1511,7 @@ static int amd_probe(struct sdhci_pci_chip *chip)
>> SDHCI_PCI_DEVICE(O2, SEABIRD0, o2),
>> SDHCI_PCI_DEVICE(O2, SEABIRD1, o2),
>> SDHCI_PCI_DEVICE(ARASAN, PHY_EMMC, arasan),
>> + SDHCI_PCI_DEVICE(SYNOPSYS, DWC_MSHC, snps),
>> SDHCI_PCI_DEVICE_CLASS(AMD, SYSTEM_SDHCI, PCI_CLASS_MASK, amd),
>> /* Generic SD host controller */
>> {PCI_DEVICE_CLASS(SYSTEM_SDHCI, PCI_CLASS_MASK)},
>> diff --git a/drivers/mmc/host/sdhci-pci-dwc-mshc.c
>> b/drivers/mmc/host/sdhci-pci-dwc-mshc.c
>> new file mode 100644
>> index 0000000..bca3db4
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci-pci-dwc-mshc.c
>> @@ -0,0 +1,146 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * SDHCI driver for Synopsys DWC_MSHC controller
>> + *
>> + * Copyright (C) 2018 Synopsys, Inc. (www.synopsys.com)
>> + *
>> + * Authors:
>> + * Prabu Thangamuthu <prabu.t@...opsys.com>
>> + * Manjunath M B <manjumb@...opsys.com>
>> + *
>> + */
>> +
>> +#include <linux/pci.h>
>> +#include <linux/delay.h>
>> +#include <linux/module.h>
>> +#include <linux/moduleparam.h>
>> +
>> +#include "sdhci.h"
>> +#include "sdhci-pci.h"
>> +#include "sdhci-pci-dwc-mshc.h"
>> +
>> +/* Default emmc vdd is set to 3.3V */
>> +static unsigned int emmc_vdd = SDHC_EMMC_VDD_330V;
>> +module_param(emmc_vdd, int, 0444);
> Why a module parameter?
Our platform has slots for eMMC devices which can supports both 1.8 V
and 3.3 V
operating modes. We want this module parameter to control the operating
voltage
of eMMC devices.
>> +
>> +static void sdhci_snps_set_clock(struct sdhci_host *host, unsigned int
>> clock)
>> +{
>> + u16 clk = 0;
>> + u32 reg = 0;
>> + u32 vendor_ptr = 0;
>> +
>> + vendor_ptr = sdhci_readw(host, SDHCI_VENDOR_PTR_R);
>> +
>> + /* Disable Software managed rx tuning */
>> + reg = sdhci_readl(host, (SDHC_AT_CTRL_R + vendor_ptr));
>> + reg &= ~SDHC_SW_TUNE_EN;
>> + sdhci_writel(host, reg, (SDHC_AT_CTRL_R + vendor_ptr));
>> +
>> + if (clock <= 52000000) {
>> + sdhci_set_clock(host, clock);
>> + } else {
>> + /* Assert reset to MMCM */
>> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
>> + reg |= SDHC_CCLK_MMCM_RST;
>> + sdhci_writel(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
>> +
>> + /* Configure MMCM*/
> Space between MMCM and *
Okay.
>
>> + sdhci_writel(host, DIV_REG_100_MHZ, SDHC_MMCM_DIV_REG);
>> + sdhci_writel(host, CLKFBOUT_100_MHZ,
>> + SDHC_MMCM_CLKFBOUT);
>> +
>> + /* De-assert reset to MMCM*/
> Space between MMCM and *
Okay.
>
>
>> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
>> + reg &= ~SDHC_CCLK_MMCM_RST;
>> + sdhci_writel(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
>> +
>> + /* Enable clock */
>> + clk = SDHCI_PROG_CLOCK_MODE | SDHCI_CLOCK_INT_EN |
>> + SDHCI_CLOCK_CARD_EN;
>> + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
>> + }
>> +}
>> +
>> +static void sdhci_snps_set_power(struct sdhci_host *host, unsigned char
>> mode,
>> + unsigned short vdd)
>> +{
>> + u8 pwr = 0;
>> + u16 ctrl;
>> +
>> + if (mode != MMC_POWER_OFF) {
>> + switch (1 << vdd) {
>> + case MMC_VDD_165_195:
>> + pwr = SDHCI_POWER_180;
>> + break;
>> + case MMC_VDD_29_30:
>> + case MMC_VDD_30_31:
>> + pwr = SDHCI_POWER_300;
>> + break;
>> + case MMC_VDD_32_33:
>> + case MMC_VDD_33_34:
>> + pwr = SDHCI_POWER_330;
>> + break;
>> + default:
>> + WARN(1, "%s: Invalid vdd %#x\n",
>> + mmc_hostname(host->mmc), vdd);
>> + break;
>> + }
>> + }
>> +
>> + if (host->pwr == pwr)
>> + return;
>> +
>> + host->pwr = pwr;
>> +
>> + if (pwr == 0) {
>> + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
>> + } else {
>> + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
>> +
>> + /*
>> + * Enable it for eMMC phy cfg1 test with 1.8V mode
>> + */
>> + if (emmc_vdd == SDHC_EMMC_VDD_180V) {
>> + pwr = SDHCI_POWER_180;
>> + sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
>> +
>> + ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
>> + /*
>> + * Enable 1.8V Signal Enable in the Host Control2
>> + * register
>> + */
>> + ctrl |= SDHCI_CTRL_VDD_180;
>> + sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
>> + }
>> + pwr |= SDHCI_POWER_ON;
>> +
>> + sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
>> + }
>> +}
>> +
>> +static int sdhci_snps_pci_probe_slot(struct sdhci_pci_slot *slot)
>> +{
>> + struct sdhci_host *host = slot->host;
>> +
>> + host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
>> + host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
> Why read caps here?
We had it for logging purpose. we will remove it.
>
>> +
>> + return 0;
>> +}
>> +
>> +/* Synopsys DWC MSHC Controller based on SDHCI-PCI */
>> +static const struct sdhci_ops sdhci_snps_ops = {
>> + .set_clock = sdhci_snps_set_clock,
>> + .set_power = sdhci_snps_set_power,
>> + .enable_dma = sdhci_pci_enable_dma,
>> + .set_bus_width = sdhci_set_bus_width,
>> + .reset = sdhci_reset,
>> + .set_uhs_signaling = sdhci_set_uhs_signaling,
>> +};
>> +
>> +const struct sdhci_pci_fixes sdhci_snps = {
>> + .probe_slot = sdhci_snps_pci_probe_slot,
>> + .ops = &sdhci_snps_ops,
>> +};
>> +
>> +MODULE_PARM_DESC(emmc_vdd, "VDD to configure eMMC device supply voltage");
>> diff --git a/drivers/mmc/host/sdhci-pci-dwc-mshc.h
>> b/drivers/mmc/host/sdhci-pci-dwc-mshc.h
>> new file mode 100644
>> index 0000000..352bbfd
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci-pci-dwc-mshc.h
> Please put the definitions into sdhci-pci-dwc-mshc.c and then this file is
> not needed.
Okay.
Thanks for review comments.
Regards,
Prabu.
Powered by blists - more mailing lists