linux-kernel - Re: [PATCH v3 01/16] mtd: rawnand: helper function for setting up ECC configuration

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20180607143759.361edb3f@xps13>
Date:   Thu, 7 Jun 2018 14:37:59 +0200
From:   Miquel Raynal <miquel.raynal@...tlin.com>
To:     Abhishek Sahu <absahu@...eaurora.org>
Cc:     Boris Brezillon <boris.brezillon@...tlin.com>,
        David Woodhouse <dwmw2@...radead.org>,
        Brian Norris <computersforpeace@...il.com>,
        Marek Vasut <marek.vasut@...il.com>,
        Richard Weinberger <richard@....at>,
        Cyrille Pitchen <cyrille.pitchen@...ev4u.fr>,
        linux-arm-msm@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-mtd@...ts.infradead.org, Andy Gross <andy.gross@...aro.org>,
        Archit Taneja <architt@...eaurora.org>,
        Masahiro Yamada <yamada.masahiro@...ionext.com>
Subject: Re: [PATCH v3 01/16] mtd: rawnand: helper function for setting up
 ECC configuration

Hi Abhishek,

On Mon, 28 May 2018 11:16:29 +0530, Abhishek Sahu
<absahu@...eaurora.org> wrote:

> On 2018-05-26 14:12, Miquel Raynal wrote:
> > Hi Abhishek,  
> > > On Fri, 25 May 2018 17:51:29 +0530, Abhishek Sahu  
> > <absahu@...eaurora.org> wrote:  
> > >> commit 2c8f8afa7f92 ("mtd: nand: add generic helpers to check,  
> >> match, maximize ECC settings") provides generic helpers which
> >> drivers can use for setting up ECC parameters.  
> >> >> Since same board can have different ECC strength nand chips so  
> >> following is the logic for setting up ECC strength and ECC step
> >> size, which can be used by most of the drivers.  
> >> >> 1. If both ECC step size and ECC strength are already set  
> >>    (usually by DT) then just check whether this setting
> >>    is supported by NAND controller.
> >> 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
> >>    supported by NAND controller.
> >> 3. Otherwise, try to match the ECC step size and ECC strength closest
> >>    to the chip's requirement. If available OOB size can't fit the chip
> >>    requirement then select maximum ECC strength which can be fit with
> >>    available OOB size.  
> >> >> This patch introduces nand_ecc_choose_conf function which calls the  
> >> required helper functions for the above logic. The drivers can use
> >> this single function instead of calling the 3 helper functions
> >> individually.  
> >> >> CC: Masahiro Yamada <yamada.masahiro@...ionext.com>  
> >> Signed-off-by: Abhishek Sahu <absahu@...eaurora.org>
> >> ---
> >> * Changes from v2:  
> >> >>   1. Renamed function to nand_ecc_choose_conf.  
> >>   2. Minor code reorganization to remove warning and 2 function calls
> >>      for nand_maximize_ecc.  
> >> >> * Changes from v1:  
> >>   NEW PATCH  
> >> >>  drivers/mtd/nand/raw/nand_base.c | 42 >> ++++++++++++++++++++++++++++++++++++++++  
> >>  drivers/mtd/nand/raw/nand_base.c | 31 +++++++++++++++++++++++++++++++
> >>  include/linux/mtd/rawnand.h      |  3 +++
> >>  2 files changed, 34 insertions(+)  
> >> >> diff --git a/drivers/mtd/nand/raw/nand_base.c >> b/drivers/mtd/nand/raw/nand_base.c  
> >> index 72f3a89..e52019d 100644
> >> --- a/drivers/mtd/nand/raw/nand_base.c
> >> +++ b/drivers/mtd/nand/raw/nand_base.c
> >> @@ -6249,6 +6249,37 @@ int nand_maximize_ecc(struct nand_chip *chip,
> >>  }
> >>  EXPORT_SYMBOL_GPL(nand_maximize_ecc);  
> >> >> +/**  
> >> + * nand_ecc_choose_conf - Set the ECC strength and ECC step size
> >> + * @chip: nand chip info structure
> >> + * @caps: ECC engine caps info structure
> >> + * @oobavail: OOB size that the ECC engine can use
> >> + *
> >> + * Choose the ECC configuration according to following logic
> >> + *
> >> + * 1. If both ECC step size and ECC strength are already set (usually >> by DT)
> >> + *    then check if it is supported by this controller.
> >> + * 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength.
> >> + * 3. Otherwise, try to match the ECC step size and ECC strength >> closest
> >> + *    to the chip's requirement. If available OOB size can't fit the >> chip
> >> + *    requirement then fallback to the maximum ECC step size and ECC >> strength.
> >> + *
> >> + * On success, the chosen ECC settings are set.
> >> + */
> >> +int nand_ecc_choose_conf(struct nand_chip *chip,
> >> +			 const struct nand_ecc_caps *caps, int oobavail)
> >> +{
> >> +	if (chip->ecc.size && chip->ecc.strength)
> >> +		return nand_check_ecc_caps(chip, caps, oobavail);
> >> +
> >> +	if (!(chip->ecc.options & NAND_ECC_MAXIMIZE) &&
> >> +	    !nand_match_ecc_req(chip, caps, oobavail))
> >> +		return 0;
> >> +
> >> +	return nand_maximize_ecc(chip, caps, oobavail);
> > > I personally don't mind if nand_maximize_ecc() is called twice in  
> > the function if it clarifies the logic. Maybe the following will be
> > more clear for the user?  
> 
>   Thanks Miquel.
>   Both the implementations are fine.
>   The above implementation (which was in Denali NAND driver) code was also
>   clear. We can go for any of these implementation.
> 
>   Shall I update this ?

Yes, please :)

> 
> > > 	if (chip->ecc.size && chip->ecc.strength)  
> > 		return nand_check_ecc_caps(chip, caps, oobavail);  
> > > 	if (chip->ecc.options & NAND_ECC_MAXIMIZE)  
> > 		return nand_maximize_ecc(chip, caps, oobavail);  
> > > 	if (!nand_match_ecc_req(chip, caps, oobavail))  
> > 		return 0;  
> > > 	return nand_maximize_ecc(chip, caps, oobavail);
> > > Also, I'm not sure we should just error out when nand_check_ecc_caps()  
> > fails. What about something more robust, like:
> >   
>   But again, It will lead in overriding the DT ECC strength parameter.
>   We started our discussion from that point. :-)

As Boris said, let's error out instead of overriding the DT ECC
parameters.


Thanks,
Miquèl