| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 15 Jun 2018 08:57:51 +0000
From: Ben Whitten <Ben.Whitten@...rdtech.com>
To: Nicolas Ferre <nicolas.ferre@...rochip.com>,
Ben Whitten <ben.whitten@...il.com>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
Alexandre Belloni <alexandre.belloni@...tlin.com>
CC: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>
Subject: RE: [PATCH 4/4] arm: dts: add support for Laird SOM60 module and DVK
boards
Thanks all for the reviews and comments, I will work on a new series.
> On 14/06/2018 at 10:51, Ben Whitten wrote:
> > Signed-off-by: Ben Whitten <ben.whitten@...rdtech.com>
> > ---
> > arch/arm/boot/dts/Makefile | 3 +-
> > arch/arm/boot/dts/at91-dvk_som60.dts | 95 +++++++++++
> > arch/arm/boot/dts/at91-dvk_su60_somc.dtsi | 159
> ++++++++++++++++++
> > arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi | 96 +++++++++++
> > arch/arm/boot/dts/at91-som60.dtsi | 229
> ++++++++++++++++++++++++++
> > 5 files changed, 581 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/boot/dts/at91-dvk_som60.dts
> > create mode 100644 arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
> > create mode 100644 arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
> > create mode 100644 arch/arm/boot/dts/at91-som60.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 486ab59..4d3d9ca 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -63,7 +63,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
> > at91-sama5d4ek.dtb \
> > at91-vinco.dtb \
>
> About where you added dtbs...
>
> > at91-wb50n.dtb \
> > - at91-gatwick.dtb
> > + at91-gatwick.dtb \
> > + at91-dvk_som60.dtb
>
> 1/ As they are based on sama5d3, I would like to see them between
> "at91-sama5d2_xplained.dtb" and "sama5d31ek.dtb"
> 2/ within this range, please sort all these 4 alphabetically
> 3/ don't laugh at me, I try to deal with our historical way of "sorting"
> entries in this Makefile for AT91... ;-)
>
> BTW, I realize now that your "at91-wb45n.dtb" entry from patch 1 should
> go just after the "at91-kizboxmini.dts" (alphabetical order in
> at91sam9x5 "location").
>
>
> > dtb-$(CONFIG_ARCH_ATLAS6) += \
> > atlas6-evb.dtb
> > dtb-$(CONFIG_ARCH_ATLAS7) += \
> > diff --git a/arch/arm/boot/dts/at91-dvk_som60.dts
> b/arch/arm/boot/dts/at91-dvk_som60.dts
> > new file mode 100644
> > index 0000000..ededd5b
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91-dvk_som60.dts
> > @@ -0,0 +1,95 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * at91-dvk_som60.dts - Device Tree file for the DVK SOM60 board
> > + *
> > + * Copyright (C) 2018 Laird,
> > + * 2018 Ben Whitten <ben.whitten@...rdtech.com>
> > + *
> > + */
> > +/dts-v1/;
> > +#include "at91-som60.dtsi"
> > +#include "at91-dvk_su60_somc.dtsi"
> > +#include "at91-dvk_su60_somc_lcm.dtsi"
> > +
> > +/ {
> > + model = "Laird DVK SOM60";
> > + compatible = "laird,dvk-som60", "laird,som60", "atmel,sama5d36",
> "atmel,sama5d3", "atmel,sama5";
> > +
> > + chosen {
> > + stdout-path = &dbgu;
> > + tick-timer = &pit;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + status = "okay";
> > +};
> > +
> > +&spi0 {
> > + status = "okay";
> > +};
> > +
> > +&ssc0 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + status = "okay";
> > +};
> > +
> > +&usart1 {
> > + status = "okay";
> > +};
> > +
> > +&usart2 {
> > + status = "okay";
> > +};
> > +
> > +&usart3 {
> > + status = "okay";
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&dbgu {
> > + status = "okay";
> > +};
> > +
> > +&pit {
> > + status = "okay";
> > +};
> > +
> > +&adc0 {
> > + status = "okay";
> > +};
> > +
> > +&can1 {
> > + status = "okay";
> > +};
> > +
> > +&macb0 {
> > + status = "okay";
> > +};
> > +
> > +&macb1 {
> > + status = "okay";
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + status = "okay";
> > +};
> > +
> > +&usb2 {
> > + status = "okay";
> > +};
> > +
> > diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
> b/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
> > new file mode 100644
> > index 0000000..6031c2f
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
> > @@ -0,0 +1,159 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * at91-dvk_su60_somc.dtsi - Device Tree file for the DVK SOM60 base
> board
> > + *
> > + * Copyright (C) 2018 Laird,
> > + * 2018 Ben Whitten <ben.whitten@...rdtech.com>
> > + *
> > + */
> > +
> > +/ {
> > + sound {
> > + compatible = "atmel,asoc-wm8904";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
> > +
> > + atmel,model = "wm8904 @ DVK-SOM60";
> > + atmel,audio-routing =
> > + "Headphone Jack", "HPOUTL",
> > + "Headphone Jack", "HPOUTR",
> > + "IN2L", "Line In Jack",
> > + "IN2R", "Line In Jack",
> > + "Mic", "MICBIAS",
> > + "IN1L", "Mic";
> > +
> > + atmel,ssc-controller = <&ssc0>;
> > + atmel,audio-codec = <&wm8904>;
> > +
> > + status = "okay";
> > + };
> > +};
> > +
> > +&mmc0 {
> > + status = "okay";
> > +
> > + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
> &pinctrl_mmc0_cd>;
> > + slot@0 {
> > + bus-width = <4>;
> > + cd-gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
> > + cd-inverted;
> > + };
> > +};
> > +
> > +&spi0 {
> > + status = "okay";
> > +
> > + /* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
> > + spi-flash@0 {
> > + compatible = "mxicy,mx25u4035", "jedec,spi-nor";
> > + spi-max-frequency = <33000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&ssc0 {
> > + atmel,clk-from-rk-pin;
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +
> > + wm8904: wm8904@1a {
> > + compatible = "wlf,wm8904";
> > + reg = <0x1a>;
> > + clocks = <&pck2>;
> > + clock-names = "mclk";
> > + };
> > +};
> > +
> > +&i2c1 {
> > + status = "okay";
> > +
> > + eeprom@87 {
> > + compatible = "giantec,24c32";
>
> It must work, however...
>
> I read in recent patches on dts directory that :
>
> "We now require all at24 users to use the "atmel,<model>" fallback in
> device tree for different manufacturers."
>
> Moreover, I don't see giantec in the vendor prefix list.
I see, I have added parts which are compatible and made note what the real
part is, should I typically be adding the real part to the compatible list and
update vendor prefixes if necessary?
>
> > + reg = <87>;
> > + pagesize = <32>;
> > + };
> > +};
> > +
> > +&usart1 {
> > + status = "okay";
> > +};
> > +
> > +&usart2 {
> > + status = "okay";
> > +};
> > +
> > +&usart3 {
> > + status = "okay";
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&dbgu {
> > + status = "okay";
> > +};
> > +
> > +&pit {
> > + status = "okay";
> > +};
> > +
> > +&adc0 {
> > + status = "okay";
> > +};
> > +
> > +&can1 {
> > + status = "okay";
> > +};
> > +
> > +&macb0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + ethernet-phy@7 {
> > + reg = <7>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_geth_int>;
> > + interrupt-parent = <&pioB>;
> > + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> > + txen-skew-ps = <800>;
> > + txc-skew-ps = <3000>;
> > + rxdv-skew-ps = <400>;
> > + rxc-skew-ps = <3000>;
> > + rxd0-skew-ps = <400>;
> > + rxd1-skew-ps = <400>;
> > + rxd2-skew-ps = <400>;
> > + rxd3-skew-ps = <400>;
> > + };
> > +};
> > +
> > +&macb1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + ethernet-phy@1 {
> > + reg = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_eth_int>;
> > + interrupt-parent = <&pioC>;
> > + interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
> > + };
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + status = "okay";
> > +};
> > +
> > +&usb2 {
> > + status = "okay";
> > +};
> > +
> > diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
> b/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
> > new file mode 100644
> > index 0000000..d98c644
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
> > @@ -0,0 +1,96 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * at91-dvk_su60_somc_lcm.dtsi - Device Tree file for the DVK SOM60 LCD
> board
> > + *
> > + * Copyright (C) 2018 Laird,
> > + * 2018 Ben Whitten <ben.whitten@...rdtech.com>
> > + *
> > + */
> > +
> > +/ {
> > + ahb {
> > + apb {
> > + pinctrl@...ff200 {
> > + board {
> > + pinctrl_lcd_ctp_int: lcd_ctp_int {
> > + atmel,pins =
> > + <AT91_PIOC 28
> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + pwms = <&hlcdc_pwm 0 50000 0>;
> > + brightness-levels = <0 4 8 16 32 64 128 255>;
> > + default-brightness-level = <6>;
> > + status = "okay";
> > + };
> > +
> > + panel: panel {
> > + /* Actually Winstar WF70GTIAGDNG0 */
> > + compatible = "innolux,at070tn92", "simple-panel";
> > + backlight = <&backlight>;
> > + power-supply = <&vcc_lcd_reg>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + port@0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > +
> > + panel_input: endpoint@0 {
> > + reg = <0>;
> > + remote-endpoint = <&hlcdc_panel_output>;
> > + };
> > + };
> > + };
> > +
> > + vcc_lcd_reg: fixedregulator_lcd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "VCC LCM";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + status = "okay";
> > + };
> > +};
> > +
> > +&i2c1 {
> > + status = "okay";
> > +
> > + ft5426@56 {
> > + /* Actually FT5426 */
> > + compatible = "edt,edt-ft5406";
> > + reg = <56>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lcd_ctp_int>;
> > +
> > + interrupt-parent = <&pioC>;
> > + interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> > +
> > + touchscreen-size-x = <800>;
> > + touchscreen-size-y = <480>;
> > + };
> > +};
> > +
> > +&hlcdc {
> > + status = "okay";
> > +
> > + hlcdc-display-controller {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
> > +
> > + port@0 {
> > + hlcdc_panel_output: endpoint@0 {
> > + reg = <0>;
> > + remote-endpoint = <&panel_input>;
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm/boot/dts/at91-som60.dtsi b/arch/arm/boot/dts/at91-
> som60.dtsi
> > new file mode 100644
> > index 0000000..1843284
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91-som60.dtsi
> > @@ -0,0 +1,229 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * at91-som60.dtsi - Device Tree file for the SOM60 module
> > + *
> > + * Copyright (C) 2018 Laird,
> > + * 2018 Ben Whitten <ben.whitten@...rdtech.com>
> > + *
> > + */
> > +#include "sama5d36.dtsi"
> > +
> > +/ {
> > + model = "Laird SOM60";
> > + compatible = "laird,som60", "atmel,sama5d36", "atmel,sama5d3",
> "atmel,sama5";
> > +
> > + chosen {
> > + stdout-path = &dbgu;
> > + };
> > +
> > + memory {
> > + reg = <0x20000000 0x8000000>;
> > + };
> > +
> > + clocks {
> > + slow_xtal {
> > + clock-frequency = <32768>;
> > + };
> > +
> > + main_xtal {
> > + clock-frequency = <12000000>;
> > + };
> > + };
> > +
> > + ahb {
> > + apb {
> > + pinctrl@...ff200 {
> > + board {
> > + pinctrl_mmc0_cd: mmc0_cd {
> > + atmel,pins =
> > + <AT91_PIOE 31
> AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> > + };
> > +
> > + pinctrl_mmc0_en: mmc0_en {
> > + atmel,pins =
> > + <AT91_PIOE 30
> AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> > + };
> > +
> > + pinctrl_nand0_wp: nand0_wp {
> > + atmel,pins =
> > + <AT91_PIOE 14
> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> > + };
> > +
> > + pinctrl_usb_vbus: usb_vbus {
> > + atmel,pins =
> > + <AT91_PIOE 20
> AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* Conflicts with USART2_SCK
> */
> > + };
> > +
> > + pinctrl_usart2_sck: usart2_sck {
> > + atmel,pins =
> > + <AT91_PIOE 20
> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* Conflicts with USB_VBUS */
> > + };
> > +
> > + pinctrl_usb_oc: usb_oc {
> > + atmel,pins =
> > + <AT91_PIOE 15
> AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* Conflicts with
> USART3_SCK */
> > + };
> > +
> > + pinctrl_usart3_sck: usart3_sck {
> > + atmel,pins =
> > + <AT91_PIOE 15
> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* Conflicts with USB_OC */
> > + };
> > +
> > + pinctrl_usba_vbus: usba_vbus {
> > + atmel,pins =
> > + <AT91_PIOC 14
> AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> > + };
> > +
> > + pinctrl_geth_int: geth_int {
> > + atmel,pins =
> > + <AT91_PIOB 25
> AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* Conflicts with
> USART1_SCK */
> > + };
> > +
> > + pinctrl_usart1_sck: usart1_sck {
> > + atmel,pins =
> > + <AT91_PIOB 25
> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* Conflicts with GETH_INT */
> > + };
> > +
> > + pinctrl_eth_int: eth_int {
> > + atmel,pins =
> > + <AT91_PIOC 10
> AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> > + };
> > +
> > + pinctrl_pck2_as_audio_mck:
> pck2_as_audio_mck {
> > + atmel,pins =
> > + <AT91_PIOC 15
> AT91_PERIPH_B AT91_PINCTRL_NONE>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
> > +&mmc0 {
> > + slot@0 {
> > + reg = <0>;
> > + bus-width = <8>;
> > + };
> > +};
> > +
> > +&mmc1 {
> > + status = "okay";
> > + slot@0 {
> > + reg = <0>;
> > + bus-width = <4>;
> > + };
> > +};
> > +
> > +&spi0 {
> > + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> > +};
> > +
> > +&usart0 {
> > + atmel,use-dma-rx;
> > + atmel,use-dma-tx;
> > + status = "okay";
> > + pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
> > +};
> > +
> > +&usart1 {
> > + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> > +};
> > +
> > +&usart2 {
> > + pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rts_cts>;
> > +};
> > +
> > +&usart3 {
> > + pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
> > +};
> > +
> > +&adc0 {
> > + pinctrl-0 = <
> > + &pinctrl_adc0_adtrg
> > + &pinctrl_adc0_ad0
> > + &pinctrl_adc0_ad1
> > + &pinctrl_adc0_ad2
> > + &pinctrl_adc0_ad3
> > + &pinctrl_adc0_ad4
> > + &pinctrl_adc0_ad5
> > + >;
> > +};
> > +
> > +&macb0 {
> > + phy-mode = "rgmii";
> > +};
> > +
> > +&macb1 {
> > + phy-mode = "rmii";
> > +};
> > +
> > +
> > +&ebi {
> > + pinctrl-0 = <&pinctrl_ebi_nand_addr>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +&nand_controller {
> > + status = "okay";
> > +
> > + nand: nand@3 {
> > + reg = <0x3 0x0 0x2>;
> > + atmel,rb = <0>;
> > + nand-bus-width = <8>;
> > + nand-ecc-mode = "hw";
> > + nand-ecc-strength = <8>;
> > + nand-ecc-step-size = <512>;
> > + nand-on-flash-bbt;
> > + label = "atmel_nand";
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + ubootspl@0 {
> > + label = "u-boot-spl";
> > + reg = <0x0 0x20000>;
> > + };
> > +
> > + uboot@...00 {
> > + label = "u-boot";
> > + reg = <0x20000 0x80000>;
> > + };
> > +
> > + ubootenv@...00 {
> > + label = "u-boot-env";
> > + reg = <0xa0000 0x20000>;
> > + };
> > +
> > + ubootenv@...00 {
> > + label = "u-boot-env";
> > + reg = <0xc0000 0x20000>;
> > + };
> > +
> > + ubi@...00 {
> > + label = "ubi";
> > + reg = <0xe0000 0xfe00000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&usb0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usba_vbus>;
> > + atmel,vbus-gpio = <&pioC 14 GPIO_ACTIVE_HIGH>;
> > +};
> > +
> > +&usb1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usb_vbus &pinctrl_usb_oc>;
> > + num-ports = <3>;
> > + atmel,vbus-gpio = <0
> > + &pioE 20 GPIO_ACTIVE_HIGH
> > + 0>;
> > + atmel,oc-gpio = <0
> > + &pioE 15 GPIO_ACTIVE_LOW
> > + 0>;
> > +};
> >
>
>
> --
> Nicolas Ferre
Powered by blists - more mailing lists