| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20180618174159.86150-1-npcomplete13@gmail.com>
Date: Mon, 18 Jun 2018 13:41:59 -0400
From: Vivek Unune <npcomplete13@...il.com>
To: florian.fainelli@...adcom.com, hauke@...ke-m.de, zajec5@...il.com,
jonmason@...adcom.com, bcm-kernel-feedback-list@...adcom.com,
robh+dt@...nel.org, mark.rutland@....com
Cc: linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, Vivek Unune <npcomplete13@...il.com>
Subject: [PATCH v3] ARM: dts: BCM5301X: Add support for Linksys EA9500
Hardware Info
-------------
Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
DDR3 RAM - 256 MB
Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
Ports - 8 Ports, 1 WAN Ports
Antennas - 8 Antennas
Serial Port - @J6 [GND,TX,RX] (VCC NC) 115200 8n1
Tested with OpenWrt built with DSA driver and Kernel v4.14
Signed-off-by: Vivek Unune <npcomplete13@...il.com>
---
Changes in v3:
- Remove unnecessary change to BCH settings
- Remove ports 5 & 7 from internal switch for now
Changes in v2:
- Properly define mdio mux, internal mdio, external mdio, mii bus
- Now we define usb3 phy as a mdio node connected to internal mdio,
thanks to work done by Rafał Miłecki on the bcm usb3 phy mdio driver
- Define external SW as a mdio-mii node connected to external mdio
---
arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 225 ++++++++++++++++++++++++
1 file changed, 225 insertions(+)
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
index 1b26f0be2382..f4f40fd7fbe5 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -31,6 +31,231 @@
linux,code = <KEY_WPS_BUTTON>;
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
};
+
+ rfkill {
+ label = "WiFi";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wps {
+ label = "bcm53xx:white:wps";
+ gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2 {
+ label = "bcm53xx:green:usb2";
+ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&ohci_port2>, <&ehci_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ usb3 {
+ label = "bcm53xx:green:usb3";
+ gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&ohci_port1>, <&ehci_port1>,
+ <&xhci_port1>;
+ linux,default-trigger = "usbport";
+ };
+
+ power {
+ label = "bcm53xx:white:power";
+ gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi-disabled {
+ label = "bcm53xx:amber:wifi-disabled";
+ gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi-enabled {
+ label = "bcm53xx:white:wifi-enabled";
+ gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar1 {
+ label = "bcm53xx:white:bluebar1";
+ gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar2 {
+ label = "bcm53xx:white:bluebar2";
+ gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar3 {
+ label = "bcm53xx:white:bluebar3";
+ gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+ };
+
+ bluebar4 {
+ label = "bcm53xx:white:bluebar4";
+ gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar5 {
+ label = "bcm53xx:white:bluebar5";
+ gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar6 {
+ label = "bcm53xx:white:bluebar6";
+ gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar7 {
+ label = "bcm53xx:white:bluebar7";
+ gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ bluebar8 {
+ label = "bcm53xx:white:bluebar8";
+ gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mdio-bus-mux {
+ mdio_ext: mdio@200 { /* BIT(9) = 1 => external mdio */
+ reg = <0x200>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ mdio-mii-mux {
+ compatible = "mdio-mux-mmioreg";
+ mdio-parent-bus = <&mdio_ext>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1800c1c0 0x4>;
+ mux-mask = <0xc0>; /* BIT(6) = mdc, BIT(7) = mdio */
+
+ mdio-mii@0 {
+ reg = <0x0>; /* Enable mii function */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@0 {
+ compatible = "brcm,bcm53125";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+ reset-names = "robo_reset";
+ reg = <0>;
+ dsa,member = <1 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan5";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan6";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan3";
+ };
+
+ sw1_p8: port@8 {
+ reg = <8>;
+ ethernet = <&sw0_p0>;
+ label = "cpu";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+ };
+};
+
+&usb2 {
+ vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+ vcc-gpio = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+};
+
+&srab {
+ compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+ status = "okay";
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ label = "lan7";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan8";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@8 {
+ reg = <8>;
+ ethernet = <&gmac2>;
+ label = "cpu";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ sw0_p0: port@0 {
+ reg = <0>;
+ label = "extsw";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
};
};
--
2.11.0
Powered by blists - more mailing lists