| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1529563351-2241-5-git-send-email-naga.sureshkumar.relli@xilinx.com>
Date: Thu, 21 Jun 2018 12:12:31 +0530
From: Naga Sureshkumar Relli <naga.sureshkumar.relli@...inx.com>
To: <boris.brezillon@...tlin.com>, <richard@....at>,
<dwmw2@...radead.org>, <computersforpeace@...il.com>,
<marek.vasut@...il.com>, <f.fainelli@...il.com>,
<mmayer@...adcom.com>, <rogerq@...com>, <ladis@...ux-mips.org>,
<ada@...rsis.com>, <honghui.zhang@...iatek.com>,
<miquel.raynal@...tlin.com>
CC: <linux-mtd@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
<nagasureshkumarrelli@...il.com>, <michals@...inx.com>,
Naga Sureshkumar Relli <naga.sureshkumar.relli@...inx.com>
Subject: [[LINUX PATCH v10] 4/4] mtd: rawnand: pl353: Add basic driver for arm pl353 smc nand interface
Add driver for arm pl353 static memory controller nand interface with HW ECC
support. This controller is used in Xilinx Zynq SoC for interfacing the NAND
flash memory.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@...inx.com>
---
Changes in 10:
- Typos correction like nand to NAND and soc to SOC etc..
- Defined macros for the values in pl353_nand_calculate_hwecc()
- Modifed ecc_status from int to char in pl353_nand_calculate_hwecc()
- Changed the return type form int to bool to the function
onehot()
- Removed udelay(1000) in pl353_cmd_function, as it is not required
- Dropped ecc->hwctl = NULL in pl353_ecc_init()
- Added an error message in pl353_ecc_init(), when there is no matching
oobsize
- Changed the variable from xnand to xnfc
- Added logic to get mtd->name from DT, if it is specified in DT
Changes in v9:
- Addressed the below comments given by Miquel
- instead of using pl353_nand_write32, use directly writel_relaxed
- Fixed check patch warnings
- Renamed write_buf/read_buf to write_data_op/read_data_op
- use BIT macro instead of 1 << nr
- Use NAND_ROW_ADDR_3 flag
- Use nand_wait_ready()
- Removed swecc functions
- Use address cycles as per size, instead of reading it from Parameter page
- Instead of writing too many patterns, use optional property
Changes in v8:
- Added exec_op() implementation
- Fixed the below v7 review comments
- removed mtd_info from pl353_nand_info struct
- Corrected ecc layout offsets
- Added on-die ecc support
Changes in v7:
- Currently not implemented the memclk rate adjustments. I will
look into this later and once the basic driver is accepted.
- Fixed GPL licence ident
Changes in v6:
- Fixed the checkpatch.pl reported warnings
- Using the address cycles information from the onfi param page
earlier it is hardcoded to 5 in driver
Changes in v5:
- Configure the nand timing parameters as per the onfi spec Changes in v4:
- Updated the driver to sync with pl353_smc driver APIs
Changes in v3:
- implemented the proper error codes
- further breakdown this patch to multiple sets
- added the controller and driver details to Documentation section
- updated the licenece to GPLv2
- reorganized the pl353_nand_ecc_init function
Changes in v2:
- use "depends on" rather than "select" option in kconfig
- remove unused variable parts
---
drivers/mtd/nand/raw/Kconfig | 7 +
drivers/mtd/nand/raw/Makefile | 1 +
drivers/mtd/nand/raw/pl353_nand.c | 1309 +++++++++++++++++++++++++++++++++++++
3 files changed, 1317 insertions(+)
create mode 100644 drivers/mtd/nand/raw/pl353_nand.c
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 6871ff0..1c5d528 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -530,4 +530,11 @@ config MTD_NAND_MTK
Enables support for NAND controller on MTK SoCs.
This controller is found on mt27xx, mt81xx, mt65xx SoCs.
+config MTD_NAND_PL353
+ tristate "ARM Pl353 NAND flash driver"
+ depends on MTD_NAND && ARM
+ depends on PL353_SMC
+ help
+ Enables support for PrimeCell Static Memory Controller PL353.
+
endif # MTD_NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index 165b7ef..1c702e1 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/
obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o
obj-$(CONFIG_MTD_NAND_MTK) += mtk_ecc.o mtk_nand.o
+obj-$(CONFIG_MTD_NAND_PL353) += pl353_nand.o
nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
nand-objs += nand_amd.o
diff --git a/drivers/mtd/nand/raw/pl353_nand.c b/drivers/mtd/nand/raw/pl353_nand.c
new file mode 100644
index 0000000..3a0acbd
--- /dev/null
+++ b/drivers/mtd/nand/raw/pl353_nand.c
@@ -0,0 +1,1309 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ARM PL353 NAND flash controller driver
+ *
+ * Copyright (C) 2017 Xilinx, Inc
+ * Author: Punnaiah chowdary kalluri <punnaiah@...inx.com>
+ * Author: Naga Sureshkumar Relli <nagasure@...inx.com>
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/pl353-smc.h>
+#include <linux/clk.h>
+
+#define PL353_NAND_DRIVER_NAME "pl353-nand"
+
+/* NAND flash driver defines */
+#define PL353_NAND_CMD_PHASE 1 /* End command valid in command phase */
+#define PL353_NAND_DATA_PHASE 2 /* End command valid in data phase */
+#define PL353_NAND_ECC_SIZE 512 /* Size of data for ECC operation */
+
+/* Flash memory controller operating parameters */
+
+#define PL353_NAND_ECC_CONFIG (BIT(4) | /* ECC read at end of page */ \
+ (0 << 5)) /* No Jumping */
+
+/* AXI Address definitions */
+#define START_CMD_SHIFT 3
+#define END_CMD_SHIFT 11
+#define END_CMD_VALID_SHIFT 20
+#define ADDR_CYCLES_SHIFT 21
+#define CLEAR_CS_SHIFT 21
+#define ECC_LAST_SHIFT 10
+#define COMMAND_PHASE (0 << 19)
+#define DATA_PHASE BIT(19)
+
+#define PL353_NAND_ECC_LAST BIT(ECC_LAST_SHIFT) /* Set ECC_Last */
+#define PL353_NAND_CLEAR_CS BIT(CLEAR_CS_SHIFT) /* Clear chip select */
+
+#define ONDIE_ECC_FEATURE_ADDR 0x90
+#define PL353_NAND_ECC_BUSY_TIMEOUT (1 * HZ)
+#define PL353_NAND_DEV_BUSY_TIMEOUT (1 * HZ)
+#define PL353_NAND_LAST_TRANSFER_LENGTH 4
+#define PL353_NAND_ECC_VALID_SHIFT 24
+#define PL353_NAND_ECC_VALID_MASK 0x40
+
+struct pl353_nfc_op {
+ u32 cmnds[4];
+ u32 thirdrow;
+ u32 type;
+ u32 end_cmd;
+ u32 addrs;
+ bool wait;
+ u32 len;
+ u32 naddrs;
+ unsigned int data_instr_idx;
+ const struct nand_op_instr *data_instr;
+ unsigned int rdy_timeout_ms;
+ unsigned int rdy_delay_ns;
+ unsigned int data_delay_ns;
+ unsigned int cle_ale_delay_ns;
+ u32 addr5;
+ u32 addr6;
+};
+
+/**
+ * struct pl353_nand_info - Defines the NAND flash driver instance
+ * @chip: NAND chip information structure
+ * @nand_base: Virtual address of the NAND flash device
+ * @end_cmd_pending: End command is pending
+ * @end_cmd: End command
+ * @row_addr_cycles: Row address cycles
+ * @col_addr_cycles: Column address cycles
+ * @address: Page address
+ * @cmd_pending: More command is needed
+ */
+struct pl353_nand_info {
+ struct nand_chip chip;
+ struct device *dev;
+ void __iomem *nand_base;
+ unsigned long end_cmd_pending;
+ unsigned long end_cmd;
+ u8 addr_cycles;
+ u32 address;
+ u32 cmd_pending;
+ struct completion complete;
+ struct clk *mclk;
+
+};
+
+static int pl353_ecc_ooblayout16_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section >= chip->ecc.steps)
+ return -ERANGE;
+
+ oobregion->offset = (section * chip->ecc.bytes);
+ oobregion->length = chip->ecc.bytes;
+
+ return 0;
+}
+
+static int pl353_ecc_ooblayout16_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section >= chip->ecc.steps)
+ return -ERANGE;
+
+ oobregion->offset = (section * chip->ecc.bytes) + 8;
+ oobregion->length = 8;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops pl353_ecc_ooblayout16_ops = {
+ .ecc = pl353_ecc_ooblayout16_ecc,
+ .free = pl353_ecc_ooblayout16_free,
+};
+
+static int pl353_ecc_ooblayout64_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section >= chip->ecc.steps)
+ return -ERANGE;
+
+ oobregion->offset = (section * chip->ecc.bytes) + 52;
+ oobregion->length = chip->ecc.bytes;
+
+ return 0;
+}
+
+static int pl353_ecc_ooblayout64_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section)
+ return -ERANGE;
+
+ if (section >= chip->ecc.steps)
+ return -ERANGE;
+
+ oobregion->offset = (section * chip->ecc.bytes) + 2;
+ oobregion->length = 50;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops pl353_ecc_ooblayout64_ops = {
+ .ecc = pl353_ecc_ooblayout64_ecc,
+ .free = pl353_ecc_ooblayout64_free,
+};
+
+/* Generic flash bbt decriptors */
+static u8 bbt_pattern[] = { 'B', 'b', 't', '0' };
+static u8 mirror_pattern[] = { '1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 4,
+ .len = 4,
+ .veroffs = 20,
+ .maxblocks = 4,
+ .pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 4,
+ .len = 4,
+ .veroffs = 20,
+ .maxblocks = 4,
+ .pattern = mirror_pattern
+};
+
+/**
+ * pl353_nand_read_data_op - read chip data into buffer
+ * @chip: Pointer to the NAND chip info structure
+ * @in: Pointer to the buffer to store read data
+ * @len: Number of bytes to read
+ * Return: Always return zero
+ */
+static int pl353_nand_read_data_op(struct nand_chip *chip,
+ u8 *in,
+ unsigned int len)
+{
+ int i;
+
+ if (IS_ALIGNED((uint32_t)in, sizeof(uint32_t)) &&
+ IS_ALIGNED(len, sizeof(uint32_t))) {
+ u32 *ptr = (u32 *)in;
+
+ len /= 4;
+ for (i = 0; i < len; i++)
+ ptr[i] = readl(chip->IO_ADDR_R);
+ } else {
+ for (i = 0; i < len; i++)
+ in[i] = readb(chip->IO_ADDR_R);
+ }
+
+ return 0;
+}
+
+/**
+ * pl353_nand_write_buf - write buffer to chip
+ * @mtd: Pointer to the mtd info structure
+ * @buf: Pointer to the buffer to store write data
+ * @len: Number of bytes to write
+ */
+static void pl353_nand_write_data_op(struct mtd_info *mtd, const u8 *buf,
+ int len)
+{
+ int i;
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) &&
+ IS_ALIGNED(len, sizeof(uint32_t))) {
+ u32 *ptr = (u32 *)buf;
+
+ len /= 4;
+ for (i = 0; i < len; i++)
+ writel(ptr[i], chip->IO_ADDR_W);
+ } else {
+ for (i = 0; i < len; i++)
+ writeb(buf[i], chip->IO_ADDR_W);
+ }
+}
+
+/**
+ * pl353_nand_calculate_hwecc - Calculate Hardware ECC
+ * @mtd: Pointer to the mtd_info structure
+ * @data: Pointer to the page data
+ * @ecc: Pointer to the ECC buffer where ECC data needs to be stored
+ *
+ * This function retrieves the Hardware ECC data from the controller and returns
+ * ECC data back to the MTD subsystem.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_calculate_hwecc(struct mtd_info *mtd,
+ const u8 *data, u8 *ecc)
+{
+ u32 ecc_value;
+ u8 ecc_reg, ecc_byte, ecc_status;
+ unsigned long timeout = jiffies + PL353_NAND_ECC_BUSY_TIMEOUT;
+ /* Wait till the ECC operation is complete or timeout */
+ do {
+ if (pl353_smc_ecc_is_busy())
+ cpu_relax();
+ else
+ break;
+ } while (!time_after_eq(jiffies, timeout));
+
+ if (time_after_eq(jiffies, timeout)) {
+ pr_err("%s timed out\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ for (ecc_reg = 0; ecc_reg < 4; ecc_reg++) {
+ /* Read ECC value for each block */
+ ecc_value = pl353_smc_get_ecc_val(ecc_reg);
+ ecc_status = (ecc_value >> PL353_NAND_ECC_VALID_SHIFT);
+ /* ECC value valid */
+ if (ecc_status & PL353_NAND_ECC_VALID_MASK) {
+ for (ecc_byte = 0; ecc_byte < 3; ecc_byte++) {
+ /* Copy ECC bytes to MTD buffer */
+ *ecc = ~ecc_value & 0xFF;
+ ecc_value = ecc_value >> 8;
+ ecc++;
+ }
+ } else {
+ pr_warn("%s status failed\n", __func__);
+ return -1;
+ }
+ }
+ return 0;
+}
+
+/**
+ * onehot - onehot function
+ * @value: Value to check for onehot
+ *
+ * This function checks whether a value is onehot or not.
+ * onehot is if and only if onebit is set.
+ *
+ * Return: 1 if it is onehot else 0
+ */
+static bool onehot(unsigned short value)
+{
+ return (value & (value - 1)) == 0;
+}
+
+/**
+ * pl353_nand_correct_data - ECC correction function
+ * @mtd: Pointer to the mtd_info structure
+ * @buf: Pointer to the page data
+ * @read_ecc: Pointer to the ECC value read from spare data area
+ * @calc_ecc: Pointer to the calculated ECC value
+ *
+ * This function corrects the ECC single bit errors & detects 2-bit errors.
+ *
+ * Return: 0 if no ECC errors found
+ * 1 if single bit error found and corrected.
+ * -1 if multiple uncorrectable ECC errors found.
+ */
+static int pl353_nand_correct_data(struct mtd_info *mtd, unsigned char *buf,
+ unsigned char *read_ecc,
+ unsigned char *calc_ecc)
+{
+ unsigned char bit_addr;
+ unsigned int byte_addr;
+ unsigned short ecc_odd, ecc_even, read_ecc_lower, read_ecc_upper;
+ unsigned short calc_ecc_lower, calc_ecc_upper;
+
+ read_ecc_lower = (read_ecc[0] | (read_ecc[1] << 8)) & 0xfff;
+ read_ecc_upper = ((read_ecc[1] >> 4) | (read_ecc[2] << 4)) & 0xfff;
+
+ calc_ecc_lower = (calc_ecc[0] | (calc_ecc[1] << 8)) & 0xfff;
+ calc_ecc_upper = ((calc_ecc[1] >> 4) | (calc_ecc[2] << 4)) & 0xfff;
+
+ ecc_odd = read_ecc_lower ^ calc_ecc_lower;
+ ecc_even = read_ecc_upper ^ calc_ecc_upper;
+
+ /* no error */
+ if (!ecc_odd && !ecc_even)
+ return 0;
+
+ if (ecc_odd == (~ecc_even & 0xfff)) {
+ /* bits [11:3] of error code is byte offset */
+ byte_addr = (ecc_odd >> 3) & 0x1ff;
+ /* bits [2:0] of error code is bit offset */
+ bit_addr = ecc_odd & 0x7;
+ /* Toggling error bit */
+ buf[byte_addr] ^= (BIT(bit_addr));
+ return 1;
+ }
+ /* one error in parity */
+ if (onehot(ecc_odd | ecc_even) == 1)
+ return 1;
+
+ /* Uncorrectable error */
+ return -1;
+}
+
+static int pl353_dev_timeout(struct mtd_info *mtd, struct nand_chip *chip,
+ unsigned long timeout)
+{
+ if (timeout)
+ timeout = jiffies + msecs_to_jiffies(timeout);
+ else
+ timeout = jiffies + PL353_NAND_DEV_BUSY_TIMEOUT;
+
+ do {
+ if (chip->dev_ready(mtd))
+ break;
+ cpu_relax();
+ } while (!time_after_eq(jiffies, timeout));
+
+ if (time_after_eq(jiffies, timeout)) {
+ pr_err("%s timed out\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+static void pl353_prepare_cmd(struct mtd_info *mtd, struct nand_chip *chip,
+ int page, int column, int start_cmd, int end_cmd,
+ bool read)
+{
+ unsigned long data_phase_addr;
+ u32 end_cmd_valid = 0;
+ void __iomem *cmd_addr;
+ unsigned long cmd_phase_addr = 0, cmd_data = 0;
+
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+
+ end_cmd_valid = read ? 1 : 0;
+
+ cmd_phase_addr = (unsigned long __force)xnfc->nand_base +
+ ((xnfc->addr_cycles
+ << ADDR_CYCLES_SHIFT) |
+ (end_cmd_valid << END_CMD_VALID_SHIFT) |
+ (COMMAND_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (start_cmd << START_CMD_SHIFT));
+ cmd_addr = (void __iomem * __force)cmd_phase_addr;
+
+ /* Get the data phase address */
+ data_phase_addr = (unsigned long __force)xnfc->nand_base +
+ ((0x0 << CLEAR_CS_SHIFT) |
+ (0 << END_CMD_VALID_SHIFT) |
+ (DATA_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (0x0 << ECC_LAST_SHIFT));
+
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ chip->IO_ADDR_W = chip->IO_ADDR_R;
+ if (chip->options & NAND_BUSWIDTH_16)
+ column /= 2;
+ cmd_data = column;
+ if (mtd->writesize > PL353_NAND_ECC_SIZE) {
+ cmd_data |= page << 16;
+ /* Another address cycle for devices > 128MiB */
+ if (chip->options & NAND_ROW_ADDR_3) {
+ writel_relaxed(cmd_data, cmd_addr);
+ cmd_data = (page >> 16);
+ }
+ } else {
+ cmd_data |= page << 8;
+ }
+
+ writel_relaxed(cmd_data, cmd_addr);
+}
+
+/**
+ * pl353_nand_read_oob - [REPLACEABLE] the most common OOB data read function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @page: Page number to read
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ unsigned long data_phase_addr;
+ u8 *p;
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+
+ chip->pagebuf = -1;
+ if (mtd->writesize < PL353_NAND_ECC_SIZE)
+ return 0;
+
+ pl353_prepare_cmd(mtd, chip, page, mtd->writesize, NAND_CMD_READ0,
+ NAND_CMD_READSTART, 1);
+
+ ndelay(100);
+ pl353_dev_timeout(mtd, chip, 0);
+
+ p = chip->oob_poi;
+ pl353_nand_read_data_op(chip, p,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ pl353_nand_read_data_op(chip, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_write_oob - [REPLACEABLE] the most common OOB data write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @page: Page number to write
+ *
+ * Return: Zero on success and EIO on failure
+ */
+static int pl353_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ const u8 *buf = chip->oob_poi;
+ unsigned long data_phase_addr;
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+ u32 addrcycles = 0;
+
+ chip->pagebuf = -1;
+ addrcycles = xnfc->addr_cycles;
+ pl353_prepare_cmd(mtd, chip, page, mtd->writesize, NAND_CMD_SEQIN,
+ NAND_CMD_PAGEPROG, 0);
+ ndelay(100);
+ pl353_nand_write_data_op(mtd, buf,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+ buf += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ pl353_nand_write_data_op(mtd, buf, PL353_NAND_LAST_TRANSFER_LENGTH);
+ nand_wait_ready(mtd);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_read_page_raw - [Intern] read raw page data without ecc
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to read
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_read_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ u8 *buf, int oob_required, int page)
+{
+ unsigned long data_phase_addr;
+ u8 *p;
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+
+ pl353_nand_read_data_op(chip, buf, mtd->writesize);
+ p = chip->oob_poi;
+ pl353_nand_read_data_op(chip, p,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ pl353_nand_read_data_op(chip, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_write_page_raw - [Intern] raw page write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to write
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_write_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf, int oob_required,
+ int page)
+{
+ unsigned long data_phase_addr;
+ u8 *p;
+
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+
+ pl353_nand_write_data_op(mtd, buf, mtd->writesize);
+ p = chip->oob_poi;
+ pl353_nand_write_data_op(mtd, p,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+
+ pl353_nand_write_data_op(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ return 0;
+}
+
+/**
+ * nand_write_page_hwecc - Hardware ECC based page write function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the data buffer
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to write
+ *
+ * This functions writes data and hardware generated ECC values in to the page.
+ *
+ * Return: Always return zero
+ */
+static int pl353_nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf, int oob_required,
+ int page)
+{
+ int eccsize = chip->ecc.size;
+ int eccsteps = chip->ecc.steps;
+ u8 *ecc_calc = chip->ecc.calc_buf;
+ u8 *oob_ptr;
+ const u8 *p = buf;
+ u32 ret;
+ unsigned long data_phase_addr;
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+
+ pl353_prepare_cmd(mtd, chip, page, 0, NAND_CMD_SEQIN,
+ NAND_CMD_PAGEPROG, 0);
+ ndelay(100);
+ for ( ; (eccsteps - 1); eccsteps--) {
+ pl353_nand_write_data_op(mtd, p, eccsize);
+ p += eccsize;
+ }
+ pl353_nand_write_data_op(mtd, p,
+ (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Set ECC Last bit to 1 */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_ECC_LAST;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ pl353_nand_write_data_op(mtd, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ p = buf;
+ chip->ecc.calculate(mtd, p, &ecc_calc[0]);
+
+ /* Wait for ECC to be calculated and read the error values */
+ ret = mtd_ooblayout_set_eccbytes(mtd, ecc_calc, chip->oob_poi,
+ 0, chip->ecc.total);
+ if (ret)
+ return ret;
+ /* Clear ECC last bit */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr -= nand_offset;
+ data_phase_addr &= ~PL353_NAND_ECC_LAST;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+
+ /* Write the spare area with ECC bytes */
+ oob_ptr = chip->oob_poi;
+ pl353_nand_write_data_op(mtd, oob_ptr,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_W;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr |= (1 << END_CMD_VALID_SHIFT);
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_W = (void __iomem * __force)data_phase_addr;
+ oob_ptr += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+ pl353_nand_write_data_op(mtd, oob_ptr, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in any
+ * case on any machine.
+ */
+ ndelay(100);
+ nand_wait_ready(mtd);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_read_page_hwecc - Hardware ECC based page read function
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ * @buf: Pointer to the buffer to store read data
+ * @oob_required: Caller requires OOB data read to chip->oob_poi
+ * @page: Page number to read
+ *
+ * This functions reads data and checks the data integrity by comparing hardware
+ * generated ECC values and read ECC values from spare area.
+ *
+ * Return: 0 always and updates ECC operation status in to MTD structure
+ */
+static int pl353_nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ u8 *buf, int oob_required, int page)
+{
+ int i, stat, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ u8 *p = buf;
+ u8 *ecc_calc = chip->ecc.calc_buf;
+ u8 *ecc = chip->ecc.code_buf;
+ unsigned int max_bitflips = 0;
+ u8 *oob_ptr;
+ u32 ret;
+ unsigned long data_phase_addr;
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ unsigned long nand_offset = (unsigned long __force)xnfc->nand_base;
+
+ pl353_prepare_cmd(mtd, chip, page, 0, NAND_CMD_READ0,
+ NAND_CMD_READSTART, 1);
+ ndelay(100);
+ pl353_dev_timeout(mtd, chip, 0);
+
+ for ( ; (eccsteps - 1); eccsteps--) {
+ pl353_nand_read_data_op(chip, p, eccsize);
+ p += eccsize;
+ }
+ pl353_nand_read_data_op(chip, p,
+ (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH));
+ p += (eccsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Set ECC Last bit to 1 */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_ECC_LAST;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ pl353_nand_read_data_op(chip, p, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ /* Read the calculated ECC value */
+ p = buf;
+ chip->ecc.calculate(mtd, p, &ecc_calc[0]);
+
+ /* Clear ECC last bit */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr -= nand_offset;
+ data_phase_addr &= ~PL353_NAND_ECC_LAST;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ /* Read the stored ECC value */
+ oob_ptr = chip->oob_poi;
+ pl353_nand_read_data_op(chip, oob_ptr,
+ (mtd->oobsize -
+ PL353_NAND_LAST_TRANSFER_LENGTH));
+
+ /* de-assert chip select */
+ data_phase_addr = (unsigned long __force)chip->IO_ADDR_R;
+ data_phase_addr -= nand_offset;
+ data_phase_addr |= PL353_NAND_CLEAR_CS;
+ data_phase_addr += nand_offset;
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+
+ oob_ptr += (mtd->oobsize - PL353_NAND_LAST_TRANSFER_LENGTH);
+ pl353_nand_read_data_op(chip, oob_ptr, PL353_NAND_LAST_TRANSFER_LENGTH);
+
+ ret = mtd_ooblayout_get_eccbytes(mtd, ecc, chip->oob_poi, 0,
+ chip->ecc.total);
+ if (ret)
+ return ret;
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ /* Check ECC error for all blocks and correct if it is correctable */
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ stat = chip->ecc.correct(mtd, p, &ecc[i], &ecc_calc[i]);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+ }
+
+ return max_bitflips;
+}
+
+/**
+ * pl353_nand_select_chip - Select the flash device
+ * @mtd: Pointer to the mtd info structure
+ * @chip: Pointer to the NAND chip info structure
+ *
+ * This function is empty as the NAND controller handles chip select line
+ * internally based on the chip address passed in command and data phase.
+ */
+static void pl353_nand_select_chip(struct mtd_info *mtd, int chip)
+{
+}
+
+/* NAND framework ->exec_op() hooks and related helpers */
+static void pl353_nfc_parse_instructions(struct nand_chip *chip,
+ const struct nand_subop *subop,
+ struct pl353_nfc_op *nfc_op)
+{
+ const struct nand_op_instr *instr = NULL;
+ unsigned int op_id, offset, naddrs;
+ int i, len;
+ const u8 *addrs;
+
+ memset(nfc_op, 0, sizeof(struct pl353_nfc_op));
+ for (op_id = 0; op_id < subop->ninstrs; op_id++) {
+ nfc_op->len = nand_subop_get_data_len(subop, op_id);
+ len = nand_subop_get_data_len(subop, op_id);
+ instr = &subop->instrs[op_id];
+ //if (subop->ninstrs == 1)
+ //nfc_op->cmnds[0] = -1;
+ switch (instr->type) {
+ case NAND_OP_CMD_INSTR:
+ nfc_op->type = NAND_OP_CMD_INSTR;
+ if (op_id)
+ nfc_op->cmnds[1] = instr->ctx.cmd.opcode;
+ else
+ nfc_op->cmnds[0] = instr->ctx.cmd.opcode;
+ nfc_op->cle_ale_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_ADDR_INSTR:
+ offset = nand_subop_get_addr_start_off(subop, op_id);
+ naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+ addrs = &instr->ctx.addr.addrs[offset];
+ nfc_op->addrs = instr->ctx.addr.addrs[offset];
+ for (i = 0; i < min_t(unsigned int, 4, naddrs); i++) {
+ nfc_op->addrs |= instr->ctx.addr.addrs[i] <<
+ (8 * i);
+ }
+
+ if (naddrs >= 5)
+ nfc_op->addr5 = addrs[4];
+ if (naddrs >= 6)
+ nfc_op->addr6 = addrs[5];
+ nfc_op->naddrs = nand_subop_get_num_addr_cyc(subop,
+ op_id);
+ nfc_op->cle_ale_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_DATA_IN_INSTR:
+ nfc_op->data_instr = instr;
+ nfc_op->type = NAND_OP_DATA_IN_INSTR;
+ nfc_op->data_instr_idx = op_id;
+ nfc_op->data_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_DATA_OUT_INSTR:
+ nfc_op->data_instr = instr;
+ nfc_op->type = NAND_OP_DATA_IN_INSTR;
+ nfc_op->data_instr_idx = op_id;
+ nfc_op->data_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_WAITRDY_INSTR:
+ nfc_op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms;
+ nfc_op->rdy_delay_ns = instr->delay_ns;
+ nfc_op->wait = true;
+ break;
+ }
+ }
+}
+
+static void cond_delay(unsigned int ns)
+{
+ if (!ns)
+ return;
+
+ if (ns < 10000)
+ ndelay(ns);
+ else
+ udelay(DIV_ROUND_UP(ns, 1000));
+}
+
+/**
+ * pl353_nand_cmd_function - Send command to NAND device
+ * @chip: Pointer to the NAND chip info structure
+ * @subop: Pointer to array of instructions
+ * Return: Always return zero
+ */
+static int pl353_nand_cmd_function(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ const struct nand_op_instr *instr;
+ struct pl353_nfc_op nfc_op = {};
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ void __iomem *cmd_addr;
+ unsigned long cmd_data = 0, end_cmd_valid = 0;
+ unsigned long cmd_phase_addr, data_phase_addr, end_cmd;
+ unsigned int op_id, len, offset;
+ bool reading;
+
+ pl353_nfc_parse_instructions(chip, subop, &nfc_op);
+ instr = nfc_op.data_instr;
+ op_id = nfc_op.data_instr_idx;
+ len = nand_subop_get_data_len(subop, op_id);
+ offset = nand_subop_get_data_start_off(subop, op_id);
+
+ pl353_smc_clr_nand_int();
+ /* Get the command phase address */
+ if (nfc_op.cmnds[1] != 0) {
+ if (nfc_op.cmnds[0] == NAND_CMD_SEQIN)
+ end_cmd_valid = 0;
+ else
+ end_cmd_valid = 1;
+ end_cmd = nfc_op.cmnds[1];
+ } else {
+ end_cmd = 0x0;
+ }
+ cmd_phase_addr = (unsigned long __force)xnfc->nand_base +
+ ((nfc_op.naddrs << ADDR_CYCLES_SHIFT) |
+ (end_cmd_valid << END_CMD_VALID_SHIFT) |
+ (COMMAND_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (nfc_op.cmnds[0] << START_CMD_SHIFT));
+
+ cmd_addr = (void __iomem * __force)cmd_phase_addr;
+ /* Get the data phase address */
+ end_cmd_valid = 0;
+
+ data_phase_addr = (unsigned long __force)xnfc->nand_base +
+ ((0x0 << CLEAR_CS_SHIFT) |
+ (end_cmd_valid << END_CMD_VALID_SHIFT) |
+ (DATA_PHASE) |
+ (end_cmd << END_CMD_SHIFT) |
+ (0x0 << ECC_LAST_SHIFT));
+ chip->IO_ADDR_R = (void __iomem * __force)data_phase_addr;
+ chip->IO_ADDR_W = chip->IO_ADDR_R;
+ /* Command phase AXI Read & Write */
+ if (nfc_op.naddrs >= 5) {
+ if (mtd->writesize > PL353_NAND_ECC_SIZE) {
+ cmd_data = nfc_op.addrs;
+ /* Another address cycle for devices > 128MiB */
+ if (chip->options & NAND_ROW_ADDR_3) {
+ writel_relaxed(cmd_data, cmd_addr);
+ cmd_data = nfc_op.addr5;
+ if (nfc_op.naddrs >= 6)
+ cmd_data |= (nfc_op.addr6 << 8);
+ }
+ }
+ } else {
+ if (nfc_op.addrs != -1) {
+ int column = nfc_op.addrs;
+ /*
+ * Change read/write column, read id etc
+ * Adjust columns for 16 bit bus width
+ */
+ if ((chip->options & NAND_BUSWIDTH_16) &&
+ (nfc_op.cmnds[0] == NAND_CMD_READ0 ||
+ nfc_op.cmnds[0] == NAND_CMD_SEQIN ||
+ nfc_op.cmnds[0] == NAND_CMD_RNDOUT ||
+ nfc_op.cmnds[0] == NAND_CMD_RNDIN)) {
+ column >>= 1;
+ }
+ cmd_data = column;
+ }
+ }
+ writel_relaxed(cmd_data, cmd_addr);
+ ndelay(100);
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+ if (!nfc_op.data_instr) {
+ msleep(nfc_op.rdy_timeout_ms);
+ cond_delay(nfc_op.rdy_delay_ns);
+ return 0;
+ }
+
+ reading = (nfc_op.data_instr->type == NAND_OP_DATA_IN_INSTR);
+
+ if (!reading) {
+ if (nfc_op.cmnds[0] == NAND_CMD_SEQIN &&
+ nfc_op.cmnds[1] == NAND_CMD_PAGEPROG) {
+ pl353_nand_write_page_raw(mtd, chip,
+ instr->ctx.data.buf.out, 0,
+ nfc_op.addrs);
+ } else {
+ pl353_nand_write_data_op(mtd, instr->ctx.data.buf.out,
+ len);
+ }
+ if (nfc_op.rdy_timeout_ms)
+ pl353_dev_timeout(mtd, chip, nfc_op.rdy_timeout_ms);
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ }
+
+ else if (reading) {
+ if (nfc_op.rdy_timeout_ms)
+ pl353_dev_timeout(mtd, chip, nfc_op.rdy_timeout_ms);
+ cond_delay(nfc_op.rdy_delay_ns);
+ pl353_nand_read_data_op(chip, instr->ctx.data.buf.in, len);
+ }
+
+ return 0;
+}
+
+static const struct nand_op_parser pl353_nfc_op_parser = NAND_OP_PARSER
+ (NAND_OP_PARSER_PATTERN
+ (pl353_nand_cmd_function,
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(true, 7),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 2048)),
+ NAND_OP_PARSER_PATTERN
+ (pl353_nand_cmd_function,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, 7),
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 2048)),
+ NAND_OP_PARSER_PATTERN
+ (pl353_nand_cmd_function,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(true, 7),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+ NAND_OP_PARSER_PATTERN
+ (pl353_nand_cmd_function,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, 8),
+ NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 2048),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+ NAND_OP_PARSER_PATTERN
+ (pl353_nand_cmd_function,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false)),
+ );
+
+static int pl353_nfc_exec_op(struct nand_chip *chip,
+ const struct nand_operation *op,
+ bool check_only)
+{
+ return nand_op_parser_exec_op(chip, &pl353_nfc_op_parser,
+ op, check_only);
+}
+
+/**
+ * pl353_nand_device_ready - Check device ready/busy line
+ * @mtd: Pointer to the mtd_info structure
+ *
+ * Return: 0 on busy or 1 on ready state
+ */
+static int pl353_nand_device_ready(struct mtd_info *mtd)
+{
+ if (pl353_smc_get_nand_int_status_raw()) {
+ pl353_smc_clr_nand_int();
+ return 1;
+ }
+
+ return 0;
+}
+
+/**
+ * pl353_nand_ecc_init - Initialize the ecc information as per the ecc mode
+ * @mtd: Pointer to the mtd_info structure
+ * @ecc: Pointer to ECC control structure
+ * @ecc_mode: ondie ecc status
+ *
+ * This function initializes the ecc block and functional pointers as per the
+ * ecc mode
+ */
+static int pl353_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc,
+ int ecc_mode)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ u32 err = 0;
+
+ if (ecc_mode == NAND_ECC_ON_DIE) {
+ pl353_smc_set_ecc_mode(PL353_SMC_ECCMODE_BYPASS);
+ /*
+ * On-Die ECC spare bytes offset 8 is used for ECC codes
+ * Use the BBT pattern descriptors
+ */
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+ bitmap_set(chip->parameters.get_feature_list,
+ ONFI_FEATURE_ON_DIE_ECC, ONFI_FEATURE_ON_DIE_ECC_EN);
+ bitmap_set(chip->parameters.set_feature_list,
+ ONFI_FEATURE_ON_DIE_ECC, ONFI_FEATURE_ON_DIE_ECC_EN);
+ } else {
+ ecc->read_oob = pl353_nand_read_oob;
+ ecc->write_oob = pl353_nand_write_oob;
+
+ ecc->mode = NAND_ECC_HW;
+ /* Hardware ECC generates 3 bytes ECC code for each 512 bytes */
+ ecc->bytes = 3;
+ ecc->strength = 1;
+ ecc->calculate = pl353_nand_calculate_hwecc;
+ ecc->correct = pl353_nand_correct_data;
+ ecc->read_page = pl353_nand_read_page_hwecc;
+ ecc->size = PL353_NAND_ECC_SIZE;
+ ecc->write_page = pl353_nand_write_page_hwecc;
+ pl353_smc_set_ecc_pg_size(mtd->writesize);
+ switch (mtd->writesize) {
+ case SZ_512:
+ case SZ_1K:
+ case SZ_2K:
+ pl353_smc_set_ecc_mode(PL353_SMC_ECCMODE_APB);
+ break;
+ default:
+ /*
+ * The software ECC routines won't work with the
+ * SMC controller
+ */
+ ecc->calculate = nand_calculate_ecc;
+ ecc->correct = nand_correct_data;
+ ecc->size = 256;
+ break;
+ }
+ if (mtd->writesize <= SZ_512)
+ xnfc->addr_cycles = 1;
+ else
+ xnfc->addr_cycles = 2;
+
+ if (chip->options & NAND_ROW_ADDR_3)
+ xnfc->addr_cycles += 3;
+ else
+ xnfc->addr_cycles += 2;
+
+ if (mtd->oobsize == 16) {
+ mtd_set_ooblayout(mtd, &pl353_ecc_ooblayout16_ops);
+ } else if (mtd->oobsize == 64) {
+ mtd_set_ooblayout(mtd, &pl353_ecc_ooblayout64_ops);
+ } else {
+ err = ENXIO;
+ dev_err(xnfc->dev, "Unsupported oob Layout\n");
+ }
+ }
+ return err;
+}
+static int pl353_setup_data_interface(struct mtd_info *mtd, int csline,
+ const struct nand_data_interface *conf)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pl353_nand_info *xnfc =
+ container_of(chip, struct pl353_nand_info, chip);
+ const struct nand_sdr_timings *sdr;
+ u32 timigs[7], mckperiodps;
+
+ if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+ return -EINVAL;
+
+ sdr = nand_get_sdr_timings(conf);
+ if (IS_ERR(sdr))
+ return PTR_ERR(sdr);
+ /*
+ * SDR timings are given in pico-seconds while NFC timings must be
+ * expressed in NAND controller clock cycles.
+ */
+ mckperiodps = NSEC_PER_SEC / clk_get_rate(xnfc->mclk);
+ mckperiodps *= 1000;
+ timigs[0] = DIV_ROUND_UP(sdr->tRC_min, mckperiodps);
+ timigs[1] = DIV_ROUND_UP(sdr->tWC_min, mckperiodps);
+ timigs[2] = DIV_ROUND_UP(sdr->tREA_max, mckperiodps);
+ timigs[3] = DIV_ROUND_UP(sdr->tWP_min, mckperiodps);
+ timigs[4] = DIV_ROUND_UP(sdr->tCLR_min, mckperiodps);
+ timigs[5] = DIV_ROUND_UP(sdr->tAR_min, mckperiodps);
+ timigs[6] = DIV_ROUND_UP(sdr->tRR_min, mckperiodps);
+ pl353_smc_set_cycles(timigs[0], timigs[1], timigs[2], timigs[3],
+ timigs[4], timigs[5], timigs[6]);
+
+ return 0;
+}
+/**
+ * pl353_nand_probe - Probe method for the NAND driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function initializes the driver data structures and the hardware.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_probe(struct platform_device *pdev)
+{
+ struct pl353_nand_info *xnfc;
+ struct mtd_info *mtd;
+ struct nand_chip *chip;
+ struct resource *res;
+ struct device_node *np;
+ u32 ret;
+
+ xnfc = devm_kzalloc(&pdev->dev, sizeof(*xnfc), GFP_KERNEL);
+ if (!xnfc)
+ return -ENOMEM;
+ xnfc->dev = &pdev->dev;
+ /* Map physical address of NAND flash */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ xnfc->nand_base = devm_ioremap_resource(xnfc->dev, res);
+ if (IS_ERR(xnfc->nand_base))
+ return PTR_ERR(xnfc->nand_base);
+
+ chip = &xnfc->chip;
+ mtd = nand_to_mtd(chip);
+ chip->exec_op = pl353_nfc_exec_op;
+ nand_set_controller_data(chip, xnfc);
+ mtd->priv = chip;
+ mtd->owner = THIS_MODULE;
+ if (!mtd->name) {
+ /*
+ * If the new bindings are used and the bootloader has not been
+ * updated to pass a new mtdparts parameter on the cmdline, you
+ * should define the following property in your NAND node, ie:
+ *
+ * label = "pl353-nand";
+ *
+ * This way, mtd->name will be set by the core when
+ * nand_set_flash_node() is called.
+ */
+ mtd->name = devm_kasprintf(xnfc->dev, GFP_KERNEL,
+ "%s", PL353_NAND_DRIVER_NAME);
+ if (!mtd->name) {
+ dev_err(xnfc->dev, "Failed to allocate mtd->name\n");
+ return -ENOMEM;
+ }
+ }
+ nand_set_flash_node(chip, xnfc->dev->of_node);
+
+ /* Set address of NAND IO lines */
+ chip->IO_ADDR_R = xnfc->nand_base;
+ chip->IO_ADDR_W = xnfc->nand_base;
+ /* Set the driver entry points for MTD */
+ chip->dev_ready = pl353_nand_device_ready;
+ chip->select_chip = pl353_nand_select_chip;
+ /* If we don't set this delay driver sets 20us by default */
+ np = of_get_next_parent(xnfc->dev->of_node);
+ xnfc->mclk = of_clk_get(np, 0);
+ if (IS_ERR(xnfc->mclk)) {
+ dev_err(xnfc->dev, "Failed to retrieve MCK clk\n");
+ return PTR_ERR(xnfc->mclk);
+ }
+ chip->chip_delay = 30;
+ /* Set the device option and flash width */
+ chip->options = NAND_BUSWIDTH_AUTO;
+ chip->bbt_options = NAND_BBT_USE_FLASH;
+ platform_set_drvdata(pdev, xnfc);
+ chip->setup_data_interface = pl353_setup_data_interface;
+ /* first scan to find the device and get the page size */
+ if (nand_scan_ident(mtd, 1, NULL)) {
+ dev_err(xnfc->dev, "nand_scan_ident for NAND failed\n");
+ return -ENXIO;
+ }
+ ret = pl353_nand_ecc_init(mtd, &chip->ecc, chip->ecc.mode);
+ if (chip->options & NAND_BUSWIDTH_16)
+ pl353_smc_set_buswidth(PL353_SMC_MEM_WIDTH_16);
+ /* second phase scan */
+ if (nand_scan_tail(mtd)) {
+ dev_err(xnfc->dev, "nand_scan_tail for NAND failed\n");
+ return -ENXIO;
+ }
+
+ mtd_device_register(mtd, NULL, 0);
+
+ return 0;
+}
+
+/**
+ * pl353_nand_remove - Remove method for the NAND driver
+ * @pdev: Pointer to the platform_device structure
+ *
+ * This function is called if the driver module is being unloaded. It frees all
+ * resources allocated to the device.
+ *
+ * Return: 0 on success or error value on failure
+ */
+static int pl353_nand_remove(struct platform_device *pdev)
+{
+ struct pl353_nand_info *xnfc = platform_get_drvdata(pdev);
+ struct mtd_info *mtd = nand_to_mtd(&xnfc->chip);
+
+ /* Release resources, unregister device */
+ nand_release(mtd);
+
+ return 0;
+}
+
+/* Match table for device tree binding */
+static const struct of_device_id pl353_nand_of_match[] = {
+ { .compatible = "arm,pl353-nand-r2p1" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, pl353_nand_of_match);
+
+/*
+ * pl353_nand_driver - This structure defines the NAND subsystem platform driver
+ */
+static struct platform_driver pl353_nand_driver = {
+ .probe = pl353_nand_probe,
+ .remove = pl353_nand_remove,
+ .driver = {
+ .name = PL353_NAND_DRIVER_NAME,
+ .of_match_table = pl353_nand_of_match,
+ },
+};
+
+module_platform_driver(pl353_nand_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_ALIAS("platform:" PL353_NAND_DRIVER_NAME);
+MODULE_DESCRIPTION("ARM PL353 NAND Flash Driver");
+MODULE_LICENSE("GPL");
--
2.7.4
Powered by blists - more mailing lists