| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1530261541-23104-2-git-send-email-hayashi.kunihiko@socionext.com>
Date: Fri, 29 Jun 2018 17:38:58 +0900
From: Kunihiko Hayashi <hayashi.kunihiko@...ionext.com>
To: Kishon Vijay Abraham I <kishon@...com>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Masahiro Yamada <yamada.masahiro@...ionext.com>
Cc: linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org,
Masami Hiramatsu <masami.hiramatsu@...aro.org>,
Jassi Brar <jaswinder.singh@...aro.org>,
Kunihiko Hayashi <hayashi.kunihiko@...ionext.com>
Subject: [PATCH 1/4] dt-bindings: phy: add DT bindings for UniPhier USB3 PHY driver
Add DT bindings for PHY interface built into USB3 controller
implemented in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@...ionext.com>
---
.../devicetree/bindings/phy/uniphier-usb3-phy.txt | 118 +++++++++++++++++++++
1 file changed, 118 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/uniphier-usb3-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-phy.txt
new file mode 100644
index 0000000..3df4a486
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-phy.txt
@@ -0,0 +1,118 @@
+Socionext UniPhier USB3 PHY
+
+This describes the devicetree bindings for PHY interfaces built into
+USB3 controller implemented on Socionext UniPhier SoCs.
+The controller includes High-Speed PHY and Super-Speed PHY.
+
+USB3 High-Speed (HS) PHY
+------------------------
+
+Required properties:
+- compatible: Should contain one of the following:
+ "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
+ "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
+ "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
+ "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
+- reg: Specifies offset and length of the register set for the device.
+- #phy-cells: Should be 0.
+- clocks: A list of phandles to the clock gate for USB3 glue layer.
+ According to the clock-names, appropriate clocks are required.
+- clock-names: Should contain the following:
+ "gio", "link" - for Pro4 SoC
+ "link", "phy", "phy-ext" - for PXs3 SoC, "phy-ext" is optional.
+ "link", "phy" - for others
+- resets: A list of phandles to the reset control for USB3 glue layer.
+ According to the reset-names, appropriate resets are required.
+- reset-names: Should contain the following:
+ "gio", "link" - for Pro4 SoC
+ "link", "phy" - for others
+
+Optional properties:
+- phy-supply: A phandle to the regulator for USB VBUS.
+- nvmem-cells: Phandles to nvmem cell that contains the trimming data.
+ Available only for HS-PHY implemented on LD20 and PXs3, and
+ if unspecified, default value is used.
+- nvmem-cell-names: Should be the following names, which correspond to
+ each nvmem-cells.
+ All of the 3 parameters associated with the following names are
+ required for each port, if any one is omitted, the trimming data
+ of the port will not be set at all.
+ "rterm", "sel_t", "hs_i" - Each cell name for phy parameters
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+
+ usb-glue@...00000 {
+ compatible = "socionext,uniphier-ld20-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ phy-supply = <&usb_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+ <&usb_hs_i0>;
+ };
+ };
+
+
+USB3 Super-Speed (SS) PHY
+-------------------------
+
+Required properties:
+- compatible: Should contain one of the following:
+ "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
+ "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
+ "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
+ "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
+- reg: Specifies offset and length of the register set for the device.
+- #phy-cells: Should be 0.
+- clocks: A list of phandles to the clock gate for USB3 glue layer.
+ According to the clock-names, appropriate clocks are required.
+- clock-names:
+ "gio", "link" - for Pro4 SoC
+ "link", "phy", "phy-ext" - for PXs3 SoC, "phy-ext" is optional.
+ "link", "phy" - for others
+- resets: A list of phandles to the reset control for USB3 glue layer.
+ According to the reset-names, appropriate resets are required.
+- reset-names:
+ "gio", "link" - for Pro4 SoC
+ "link", "phy" - for others
+
+Optional properties:
+- phy-supply: A phandle to the regulator for USB VBUS.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+
+ usb-glue@...00000 {
+ compatible = "socionext,uniphier-ld20-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-ld20-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ phy-supply = <&usb_vbus0>;
+ };
+
+ other nodes ...
+ };
--
2.7.4
Powered by blists - more mailing lists