| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20180703220029.19565-17-miquel.raynal@bootlin.com>
Date: Wed, 4 Jul 2018 00:00:13 +0200
From: Miquel Raynal <miquel.raynal@...tlin.com>
To: Wenyou Yang <wenyou.yang@...rochip.com>,
Josh Wu <rainyfeeling@...look.com>,
Tudor Ambarus <Tudor.Ambarus@...rochip.com>,
Boris Brezillon <boris.brezillon@...tlin.com>,
Miquel Raynal <miquel.raynal@...tlin.com>,
Richard Weinberger <richard@....at>,
David Woodhouse <dwmw2@...radead.org>,
Brian Norris <computersforpeace@...il.com>,
Marek Vasut <marek.vasut@...il.com>,
Nicolas Ferre <nicolas.ferre@...rochip.com>,
Alexandre Belloni <alexandre.belloni@...tlin.com>,
Kamal Dasu <kdasu.kdev@...il.com>,
Masahiro Yamada <yamada.masahiro@...ionext.com>,
Han Xu <han.xu@....com>,
Harvey Hunt <harveyhuntnexus@...il.com>,
Vladimir Zapolskiy <vz@...ia.com>,
Sylvain Lemieux <slemieux.tyco@...il.com>,
Xiaolei Li <xiaolei.li@...iatek.com>,
Matthias Brugger <matthias.bgg@...il.com>,
Maxime Ripard <maxime.ripard@...tlin.com>,
Chen-Yu Tsai <wens@...e.org>,
Marc Gonzalez <marc.w.gonzalez@...e.fr>,
Mans Rullgard <mans@...sr.com>, Stefan Agner <stefan@...er.ch>
Cc: linux-mtd@...ts.infradead.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
bcm-kernel-feedback-list@...adcom.com,
linux-mediatek@...ts.infradead.org
Subject: [PATCH v2 16/32] mtd: rawnand: mxc: convert driver to nand_scan()
Two helpers have been added to the core to make ECC-related
configuration between the detection phase and the final NAND scan. Use
these hooks and convert the driver to just use nand_scan() instead of
both nand_scan_ident() and nand_scan_tail().
Signed-off-by: Miquel Raynal <miquel.raynal@...tlin.com>
---
drivers/mtd/nand/raw/mxc_nand.c | 132 ++++++++++++++++++++--------------------
1 file changed, 67 insertions(+), 65 deletions(-)
diff --git a/drivers/mtd/nand/raw/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
index 90cfb5e730aa..3c0451433247 100644
--- a/drivers/mtd/nand/raw/mxc_nand.c
+++ b/drivers/mtd/nand/raw/mxc_nand.c
@@ -1706,6 +1706,70 @@ static int mxcnd_probe_dt(struct mxc_nand_host *host)
}
#endif
+static int mxcnd_attach_chip(struct nand_chip *chip)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct mxc_nand_host *host = nand_get_controller_data(chip);
+ struct device *dev = mtd->dev.parent;
+
+ switch (chip->ecc.mode) {
+ case NAND_ECC_HW:
+ chip->ecc.read_page = mxc_nand_read_page;
+ chip->ecc.read_page_raw = mxc_nand_read_page_raw;
+ chip->ecc.read_oob = mxc_nand_read_oob;
+ chip->ecc.write_page = mxc_nand_write_page_ecc;
+ chip->ecc.write_page_raw = mxc_nand_write_page_raw;
+ chip->ecc.write_oob = mxc_nand_write_oob;
+ break;
+
+ case NAND_ECC_SOFT:
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ if (chip->bbt_options & NAND_BBT_USE_FLASH) {
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+ }
+
+ /* Allocate the right size buffer now */
+ devm_kfree(dev, (void *)host->data_buf);
+ host->data_buf = devm_kzalloc(dev, mtd->writesize + mtd->oobsize,
+ GFP_KERNEL);
+ if (!host->data_buf)
+ return -ENOMEM;
+
+ /* Call preset again, with correct writesize chip time */
+ host->devtype_data->preset(mtd);
+
+ if (!chip->ecc.bytes) {
+ if (host->eccsize == 8)
+ chip->ecc.bytes = 18;
+ else if (host->eccsize == 4)
+ chip->ecc.bytes = 9;
+ }
+
+ /*
+ * Experimentation shows that i.MX NFC can only handle up to 218 oob
+ * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare()
+ * into copying invalid data to/from the spare IO buffer, as this
+ * might cause ECC data corruption when doing sub-page write to a
+ * partially written page.
+ */
+ host->used_oobsize = min(mtd->oobsize, 218U);
+
+ if (chip->ecc.mode == NAND_ECC_HW) {
+ if (is_imx21_nfc(host) || is_imx27_nfc(host))
+ chip->ecc.strength = 1;
+ else
+ chip->ecc.strength = (host->eccsize == 4) ? 4 : 8;
+ }
+
+ return 0;
+}
+
static int mxcnd_probe(struct platform_device *pdev)
{
struct nand_chip *this;
@@ -1845,71 +1909,9 @@ static int mxcnd_probe(struct platform_device *pdev)
host->devtype_data->irq_control(host, 1);
}
- /* first scan to find the device and get the page size */
- err = nand_scan_ident(mtd, is_imx25_nfc(host) ? 4 : 1, NULL);
- if (err)
- goto escan;
-
- switch (this->ecc.mode) {
- case NAND_ECC_HW:
- this->ecc.read_page = mxc_nand_read_page;
- this->ecc.read_page_raw = mxc_nand_read_page_raw;
- this->ecc.read_oob = mxc_nand_read_oob;
- this->ecc.write_page = mxc_nand_write_page_ecc;
- this->ecc.write_page_raw = mxc_nand_write_page_raw;
- this->ecc.write_oob = mxc_nand_write_oob;
- break;
-
- case NAND_ECC_SOFT:
- break;
-
- default:
- err = -EINVAL;
- goto escan;
- }
-
- if (this->bbt_options & NAND_BBT_USE_FLASH) {
- this->bbt_td = &bbt_main_descr;
- this->bbt_md = &bbt_mirror_descr;
- }
-
- /* allocate the right size buffer now */
- devm_kfree(&pdev->dev, (void *)host->data_buf);
- host->data_buf = devm_kzalloc(&pdev->dev, mtd->writesize + mtd->oobsize,
- GFP_KERNEL);
- if (!host->data_buf) {
- err = -ENOMEM;
- goto escan;
- }
-
- /* Call preset again, with correct writesize this time */
- host->devtype_data->preset(mtd);
-
- if (!this->ecc.bytes) {
- if (host->eccsize == 8)
- this->ecc.bytes = 18;
- else if (host->eccsize == 4)
- this->ecc.bytes = 9;
- }
-
- /*
- * Experimentation shows that i.MX NFC can only handle up to 218 oob
- * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare()
- * into copying invalid data to/from the spare IO buffer, as this
- * might cause ECC data corruption when doing sub-page write to a
- * partially written page.
- */
- host->used_oobsize = min(mtd->oobsize, 218U);
-
- if (this->ecc.mode == NAND_ECC_HW) {
- if (is_imx21_nfc(host) || is_imx27_nfc(host))
- this->ecc.strength = 1;
- else
- this->ecc.strength = (host->eccsize == 4) ? 4 : 8;
- }
-
- /* second phase scan */
- err = nand_scan_tail(mtd);
+ /* Scan the NAND device */
+ this->hwcontrol.attach_chip = mxcnd_attach_chip;
+ err = nand_scan(mtd, is_imx25_nfc(host) ? 4 : 1);
if (err)
goto escan;
--
2.14.1
Powered by blists - more mailing lists