Message-Id: <1531415381-16885-1-git-send-email-anischal@codeaurora.org>
Date:   Thu, 12 Jul 2018 22:39:37 +0530
From:   Amit Nischal <anischal@...eaurora.org>
To:     Stephen Boyd <sboyd@...nel.org>,
        Michael Turquette <mturquette@...libre.com>
Cc:     Andy Gross <andy.gross@...aro.org>,
        David Brown <david.brown@...aro.org>,
        Rajendra Nayak <rnayak@...eaurora.org>,
        Odelu Kukatla <okukatla@...eaurora.org>,
        Taniya Das <tdas@...eaurora.org>,
        linux-arm-msm@...r.kernel.org, linux-soc@...r.kernel.org,
        linux-clk@...r.kernel.org, linux-kernel@...r.kernel.org,
        Amit Nischal <anischal@...eaurora.org>
Subject: [PATCH v2 0/4] Add QCOM graphics clock controller driver for SDM845

Changes in v2:
Addressed review comments given by Stephen: https://lkml.org/lkml/2018/6/6/294
* Introduce clk_rcg2_gfx3d_determine_rate ops to return the best parent
  as 'gpucc_pll0_even' and best parent rate as twice of the requested rate
  always. This will eliminate the need of frequency table as source and
  div-2 are fixed for gfx3d_clk_src.
  Also modified the clk_rcg2_set_rate ops to configure the fixed source and
  div.
* Add support to check if requested rate falls within allowed set_rate range.
  This will not let the source gpucc_pll0 to go out of the supported range
  and also client can request the rate within the range.
* Fixed comment text in probe function and added module description for GPUCC
  driver.

The graphics clock driver depends upon the below change.
	https://lkml.org/lkml/2018/6/23/108

Changes in v1:
This patch series adds support for graphics clock controller for SDM845.
Below is the brief description for each change:

1. For some of the GDSCs, there is requirement to enable/disable the
   few clocks before turning on/off the gdsc power domain. This patch
   will add support to enable/disable the clock associated with the
   gdsc along with power domain on/off callbacks.

2. To turn on the gpu_gx_gdsc, there is a hardware requirement to
   turn on the root clock (GFX3D RCG) first which would be the turn
   on signal for the gdsc along with the SW_COLLAPSE. As per the
   current implementation of clk_rcg2_shared_ops, it clears the
   root_enable bit in the enable() clock ops. But due to the above
   said requirement for GFX3D shared RCG, root_enable bit would be
   already set by gdsc driver and rcg2_shared_ops should not clear
   the root unless the disable() is called.

   This patch add support for the same by reusing the existing
   clk_rcg2_shared_ops and deriving "clk_rcg2_gfx3d_ops" clk_ops
   for GFX3D clock to take care of the root set/clear requirement.

3. Add device tree bindings for graphics clock controller for SDM845.

4. Add graphics clock controller (GPUCC) driver for SDM845.

[v1] : https://lkml.org/lkml/2018/6/6/294

Amit Nischal (4):
  clk: qcom: gdsc: Add support to enable/disable the clocks with GDSC
  clk: qcom: Add clk_rcg2_gfx3d_ops for SDM845
  dt-bindings: clock: Introduce QCOM Graphics clock bindings
  clk: qcom: Add graphics clock controller driver for SDM845

 .../devicetree/bindings/clock/qcom,gpucc.txt       |  18 +
 drivers/clk/qcom/Kconfig                           |   9 +
 drivers/clk/qcom/Makefile                          |   1 +
 drivers/clk/qcom/clk-rcg.h                         |   1 +
 drivers/clk/qcom/clk-rcg2.c                        |  87 +++-
 drivers/clk/qcom/gdsc.c                            |  44 +++
 drivers/clk/qcom/gdsc.h                            |   5 +
 drivers/clk/qcom/gpucc-sdm845.c                    | 438 +++++++++++++++++++++
 include/dt-bindings/clock/qcom,gpucc-sdm845.h      |  38 ++
 9 files changed, 639 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,gpucc.txt
 create mode 100644 drivers/clk/qcom/gpucc-sdm845.c
 create mode 100644 include/dt-bindings/clock/qcom,gpucc-sdm845.h

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation

Powered by blists - more mailing lists