| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20180718121130.GA16683@mani>
Date: Wed, 18 Jul 2018 17:41:30 +0530
From: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To: andy.gross@...aro.org
Cc: linus.walleij@...aro.org, bjorn.andersson@...aro.org,
amit.kucheria@...aro.org, nicolas.dechesne@...aro.org,
todor.tomov@...aro.org, linux-arm-msm@...r.kernel.org,
linux-soc@...r.kernel.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2 1/1] dts: qcom: db820c: Add gpio-line-names property
On Wed, Apr 18, 2018 at 07:16:01PM +0530, Manivannan Sadhasivam wrote:
> Add gpio-line-names property for Dragonboard820c based on APQ8096 SoC.
> There are 4 gpio-controllers present on this board, including the
> APQ8096 SoC, PM8994 (GPIO and MPP) and PMI8994 (GPIO).
>
> Lines names are derived from 96Boards CE Specification 1.0, Appendix
> "Expansion Connector Signal Description". Line names for PMI8994 MPP
> pins are not added due to the absence of the gpio-controller support.
>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
Hi Andy,
Any update on this patch? We have got 3 reviews so far...
Thanks,
Mani
> ---
> arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 239 +++++++++++++++++++++++++++
> 1 file changed, 239 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
> index 1c8f1b86472d..473530527e27 100644
> --- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
> +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
> @@ -19,6 +19,33 @@
> #include <dt-bindings/input/input.h>
> #include <dt-bindings/gpio/gpio.h>
>
> +/*
> + * GPIO name legend: proper name = the GPIO line is used as GPIO
> + * NC = not connected (pin out but not routed from the chip to
> + * anything the board)
> + * "[PER]" = pin is muxed for [peripheral] (not GPIO)
> + * LSEC = Low Speed External Connector
> + * P HSEC = Primary High Speed External Connector
> + * S HSEC = Secondary High Speed External Connector
> + * J14 = Camera Connector
> + * TP = Test Points
> + *
> + * Line names are taken from the schematic "DragonBoard 820c",
> + * drawing no: LM25-P2751-1
> + *
> + * For the lines routed to the external connectors the
> + * lines are named after the 96Boards CE Specification 1.0,
> + * Appendix "Expansion Connector Signal Description".
> + *
> + * When the 96Board naming of a line and the schematic name of
> + * the same line are in conflict, the 96Board specification
> + * takes precedence, which means that the external UART on the
> + * LSEC is named UART0 while the schematic and SoC names this
> + * UART3. This is only for the informational lines i.e. "[FOO]",
> + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
> + * ones actually used for GPIO.
> + */
> +
> / {
> aliases {
> serial0 = &blsp2_uart1;
> @@ -90,6 +117,218 @@
> status = "okay";
> };
>
> + pinctrl@...0000 {
> + gpio-line-names =
> + "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
> + "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
> + "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
> + "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
> + "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
> + "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
> + "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
> + "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
> + "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
> + "TP93", /* GPIO_9 */
> + "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
> + "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
> + "NC", /* GPIO_12 */
> + "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
> + "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
> + "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
> + "TP99", /* GPIO_16 */
> + "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
> + "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
> + "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
> + "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
> + "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
> + "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
> + "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
> + "GPIO-D", /* GPIO_24, LSEC pin 26 */
> + "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
> + "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
> + "BLSP6_I2C_SDA", /* GPIO_27 */
> + "BLSP6_I2C_SCL", /* GPIO_28 */
> + "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
> + "GPIO30", /* GPIO_30, S HSEC pin 4 */
> + "HDMI_CEC", /* GPIO_31 */
> + "HDMI_DDC_CLOCK", /* GPIO_32 */
> + "HDMI_DDC_DATA", /* GPIO_33 */
> + "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
> + "PCIE0_RST_N", /* GPIO_35 */
> + "PCIE0_CLKREQ_N", /* GPIO_36 */
> + "PCIE0_WAKE", /* GPIO_37 */
> + "SD_CARD_DET_N", /* GPIO_38 */
> + "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
> + "W_DISABLE_N", /* GPIO_40 */
> + "[BLSP9_UART_TX]", /* GPIO_41 */
> + "[BLSP9_UART_RX]", /* GPIO_42 */
> + "[BLSP2_UART_CTS_N]", /* GPIO_43 */
> + "[BLSP2_UART_RFR_N]", /* GPIO_44 */
> + "[BLSP3_UART_TX]", /* GPIO_45 */
> + "[BLSP3_UART_RX]", /* GPIO_46 */
> + "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
> + "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
> + "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
> + "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
> + "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
> + "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
> + "[CODEC_INT1_N]", /* GPIO_53 */
> + "[CODEC_INT2_N]", /* GPIO_54 */
> + "[BLSP7_I2C_SDA]", /* GPIO_55 */
> + "[BLSP7_I2C_SCL]", /* GPIO_56 */
> + "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
> + "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
> + "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
> + "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
> + "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
> + "GPIO-E", /* GPIO_62, LSEC pin 27 */
> + "TP87", /* GPIO_63 */
> + "[CODEC_RST_N]", /* GPIO_64 */
> + "[PCM1_CLK]", /* GPIO_65 */
> + "[PCM1_SYNC]", /* GPIO_66 */
> + "[PCM1_DIN]", /* GPIO_67 */
> + "[PCM1_DOUT]", /* GPIO_68 */
> + "AUDIO_REF_CLK", /* GPIO_69 */
> + "SLIMBUS_CLK", /* GPIO_70 */
> + "SLIMBUS_DATA0", /* GPIO_71 */
> + "SLIMBUS_DATA1", /* GPIO_72 */
> + "NC", /* GPIO_73 */
> + "NC", /* GPIO_74 */
> + "NC", /* GPIO_75 */
> + "NC", /* GPIO_76 */
> + "TP94", /* GPIO_77 */
> + "NC", /* GPIO_78 */
> + "TP95", /* GPIO_79 */
> + "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
> + "TP88", /* GPIO_81 */
> + "TP89", /* GPIO_82 */
> + "TP90", /* GPIO_83 */
> + "TP91", /* GPIO_84 */
> + "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
> + "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
> + "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
> + "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
> + "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
> + "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
> + "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
> + "NC", /* GPIO_92 */
> + "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
> + "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
> + "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
> + "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
> + "NC", /* GPIO_97 */
> + "CAM1_STANDBY_N", /* GPIO_98 */
> + "NC", /* GPIO_99 */
> + "NC", /* GPIO_100 */
> + "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
> + "BOOT_CONFIG1", /* GPIO_102 */
> + "USB_HUB_RESET", /* GPIO_103 */
> + "CAM1_RST_N", /* GPIO_104 */
> + "NC", /* GPIO_105 */
> + "NC", /* GPIO_106 */
> + "NC", /* GPIO_107 */
> + "NC", /* GPIO_108 */
> + "NC", /* GPIO_109 */
> + "NC", /* GPIO_110 */
> + "NC", /* GPIO_111 */
> + "NC", /* GPIO_112 */
> + "PMI8994_BUA", /* GPIO_113 */
> + "PCIE2_RST_N", /* GPIO_114 */
> + "PCIE2_CLKREQ_N", /* GPIO_115 */
> + "PCIE2_WAKE", /* GPIO_116 */
> + "SSC_IRQ_0", /* GPIO_117 */
> + "SSC_IRQ_1", /* GPIO_118 */
> + "SSC_IRQ_2", /* GPIO_119 */
> + "NC", /* GPIO_120 */
> + "GPIO121", /* GPIO_121, S HSEC pin 2 */
> + "NC", /* GPIO_122 */
> + "SSC_IRQ_6", /* GPIO_123 */
> + "SSC_IRQ_7", /* GPIO_124 */
> + "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
> + "BOOT_CONFIG5", /* GPIO_126 */
> + "NC", /* GPIO_127 */
> + "NC", /* GPIO_128 */
> + "BOOT_CONFIG7", /* GPIO_129 */
> + "PCIE1_RST_N", /* GPIO_130 */
> + "PCIE1_CLKREQ_N", /* GPIO_131 */
> + "PCIE1_WAKE", /* GPIO_132 */
> + "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
> + "NC", /* GPIO_134 */
> + "NC", /* GPIO_135 */
> + "BOOT_CONFIG8", /* GPIO_136 */
> + "NC", /* GPIO_137 */
> + "NC", /* GPIO_138 */
> + "GPS_SSBI2", /* GPIO_139 */
> + "GPS_SSBI1", /* GPIO_140 */
> + "NC", /* GPIO_141 */
> + "NC", /* GPIO_142 */
> + "NC", /* GPIO_143 */
> + "BOOT_CONFIG6", /* GPIO_144 */
> + "NC", /* GPIO_145 */
> + "NC", /* GPIO_146 */
> + "NC", /* GPIO_147 */
> + "NC", /* GPIO_148 */
> + "NC"; /* GPIO_149 */
> + };
> +
> + qcom,spmi@...f000 {
> + pmic@0 {
> + gpios@...0 {
> + gpio-line-names =
> + "NC",
> + "KEY_VOLP_N",
> + "NC",
> + "BL1_PWM",
> + "GPIO-F", /* BL0_PWM, LSEC pin 28 */
> + "BL1_EN",
> + "NC",
> + "WLAN_EN",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "DIVCLK1",
> + "DIVCLK2",
> + "DIVCLK3",
> + "DIVCLK4",
> + "BT_EN",
> + "PMIC_SLB",
> + "PMIC_BUA",
> + "USB_VBUS_DET";
> + };
> +
> + mpps@...0 {
> + gpio-line-names =
> + "VDDPX_BIAS",
> + "WIFI_LED",
> + "NC",
> + "BT_LED",
> + "PM_MPP05",
> + "PM_MPP06",
> + "PM_MPP07",
> + "NC";
> + };
> + };
> +
> + pmic@2 {
> + gpios@...0 {
> + gpio-line-names =
> + "NC",
> + "SPKR_AMP_EN1",
> + "SPKR_AMP_EN2",
> + "TP61",
> + "NC",
> + "USB2_VBUS_DET",
> + "NC",
> + "NC",
> + "NC",
> + "NC";
> + };
> + };
> + };
> +
> phy@...00 {
> status = "okay";
> };
> --
> 2.14.1
>
Powered by blists - more mailing lists