| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20180719230026.8741-8-miquel.raynal@bootlin.com>
Date: Fri, 20 Jul 2018 01:00:00 +0200
From: Miquel Raynal <miquel.raynal@...tlin.com>
To: Wenyou Yang <wenyou.yang@...rochip.com>,
Josh Wu <rainyfeeling@...look.com>,
Tudor Ambarus <Tudor.Ambarus@...rochip.com>,
Boris Brezillon <boris.brezillon@...tlin.com>,
Miquel Raynal <miquel.raynal@...tlin.com>,
Richard Weinberger <richard@....at>,
David Woodhouse <dwmw2@...radead.org>,
Brian Norris <computersforpeace@...il.com>,
Marek Vasut <marek.vasut@...il.com>,
Nicolas Ferre <nicolas.ferre@...rochip.com>,
Alexandre Belloni <alexandre.belloni@...tlin.com>,
Kamal Dasu <kdasu.kdev@...il.com>,
Masahiro Yamada <yamada.masahiro@...ionext.com>,
Han Xu <han.xu@....com>,
Harvey Hunt <harveyhuntnexus@...il.com>,
Vladimir Zapolskiy <vz@...ia.com>,
Sylvain Lemieux <slemieux.tyco@...il.com>,
Xiaolei Li <xiaolei.li@...iatek.com>,
Matthias Brugger <matthias.bgg@...il.com>,
Maxime Ripard <maxime.ripard@...tlin.com>,
Chen-Yu Tsai <wens@...e.org>,
Marc Gonzalez <marc.w.gonzalez@...e.fr>,
Mans Rullgard <mans@...sr.com>, Stefan Agner <stefan@...er.ch>
Cc: linux-mtd@...ts.infradead.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
bcm-kernel-feedback-list@...adcom.com,
linux-mediatek@...ts.infradead.org
Subject: [PATCH v3 07/33] mtd: rawnand: fsmc: convert driver to nand_scan()
Two helpers have been added to the core to make ECC-related
configuration between the detection phase and the final NAND scan. Use
these hooks and convert the driver to just use nand_scan() instead of
both nand_scan_ident() and nand_scan_tail().
Signed-off-by: Miquel Raynal <miquel.raynal@...tlin.com>
---
drivers/mtd/nand/raw/fsmc_nand.c | 148 +++++++++++++++++++++------------------
1 file changed, 78 insertions(+), 70 deletions(-)
diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c
index 59524d181bfe..020495e6cd55 100644
--- a/drivers/mtd/nand/raw/fsmc_nand.c
+++ b/drivers/mtd/nand/raw/fsmc_nand.c
@@ -919,6 +919,82 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev,
return 0;
}
+static int fsmc_nand_attach_chip(struct nand_chip *nand)
+{
+ struct mtd_info *mtd = nand_to_mtd(nand);
+ struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
+
+ if (AMBA_REV_BITS(host->pid) >= 8) {
+ switch (mtd->oobsize) {
+ case 16:
+ case 64:
+ case 128:
+ case 224:
+ case 256:
+ break;
+ default:
+ dev_warn(host->dev,
+ "No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
+ return -EINVAL;
+ }
+
+ mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops);
+
+ return 0;
+ }
+
+ switch (nand->ecc.mode) {
+ case NAND_ECC_HW:
+ dev_info(host->dev, "Using 1-bit HW ECC scheme\n");
+ nand->ecc.calculate = fsmc_read_hwecc_ecc1;
+ nand->ecc.correct = nand_correct_data;
+ nand->ecc.bytes = 3;
+ nand->ecc.strength = 1;
+ break;
+
+ case NAND_ECC_SOFT:
+ if (nand->ecc.algo == NAND_ECC_BCH) {
+ dev_info(host->dev,
+ "Using 4-bit SW BCH ECC scheme\n");
+ break;
+ }
+
+ case NAND_ECC_ON_DIE:
+ break;
+
+ default:
+ dev_err(host->dev, "Unsupported ECC mode!\n");
+ return -ENOTSUPP;
+ }
+
+ /*
+ * Don't set layout for BCH4 SW ECC. This will be
+ * generated later in nand_bch_init() later.
+ */
+ if (nand->ecc.mode == NAND_ECC_HW) {
+ switch (mtd->oobsize) {
+ case 16:
+ case 64:
+ case 128:
+ mtd_set_ooblayout(mtd,
+ &fsmc_ecc1_ooblayout_ops);
+ break;
+ default:
+ dev_warn(host->dev,
+ "No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static struct nand_controller_ops fsmc_nand_controller_ops = {
+ .attach_chip = fsmc_nand_attach_chip,
+};
+
/*
* fsmc_nand_probe - Probe function
* @pdev: platform device structure
@@ -1048,76 +1124,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
/*
* Scan to find existence of the device
*/
- ret = nand_scan_ident(mtd, 1, NULL);
- if (ret) {
- dev_err(&pdev->dev, "No NAND Device found!\n");
- goto release_dma_write_chan;
- }
-
- if (AMBA_REV_BITS(host->pid) >= 8) {
- switch (mtd->oobsize) {
- case 16:
- case 64:
- case 128:
- case 224:
- case 256:
- break;
- default:
- dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n",
- mtd->oobsize);
- ret = -EINVAL;
- goto release_dma_write_chan;
- }
-
- mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops);
- } else {
- switch (nand->ecc.mode) {
- case NAND_ECC_HW:
- dev_info(&pdev->dev, "Using 1-bit HW ECC scheme\n");
- nand->ecc.calculate = fsmc_read_hwecc_ecc1;
- nand->ecc.correct = nand_correct_data;
- nand->ecc.bytes = 3;
- nand->ecc.strength = 1;
- break;
-
- case NAND_ECC_SOFT:
- if (nand->ecc.algo == NAND_ECC_BCH) {
- dev_info(&pdev->dev, "Using 4-bit SW BCH ECC scheme\n");
- break;
- }
-
- case NAND_ECC_ON_DIE:
- break;
-
- default:
- dev_err(&pdev->dev, "Unsupported ECC mode!\n");
- goto release_dma_write_chan;
- }
-
- /*
- * Don't set layout for BCH4 SW ECC. This will be
- * generated later in nand_bch_init() later.
- */
- if (nand->ecc.mode == NAND_ECC_HW) {
- switch (mtd->oobsize) {
- case 16:
- case 64:
- case 128:
- mtd_set_ooblayout(mtd,
- &fsmc_ecc1_ooblayout_ops);
- break;
- default:
- dev_warn(&pdev->dev,
- "No oob scheme defined for oobsize %d\n",
- mtd->oobsize);
- ret = -EINVAL;
- goto release_dma_write_chan;
- }
- }
- }
-
- /* Second stage of scan to fill MTD data-structures */
- ret = nand_scan_tail(mtd);
+ nand->dummy_controller.ops = &fsmc_nand_controller_ops;
+ ret = nand_scan(mtd, 1);
if (ret)
goto release_dma_write_chan;
--
2.14.1
Powered by blists - more mailing lists