Message-ID: <20180730170725.GB2511@Mani-XPS-13-9360>
Date:   Mon, 30 Jul 2018 22:37:25 +0530
From:   Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To:     wsa@...-dreams.de
Cc:     robh+dt@...nel.org, afaerber@...e.de, linus.walleij@...aro.org,
        linux-i2c@...r.kernel.org, liuwei@...ions-semi.com,
        mp-cs@...ions-semi.com, 96boards@...obotics.com,
        devicetree@...r.kernel.org, andy.shevchenko@...il.com,
        daniel.thompson@...aro.org, amit.kucheria@...aro.org,
        linux-arm-kernel@...ts.infradead.org, linux-gpio@...r.kernel.org,
        linux-kernel@...r.kernel.org, hzhang@...obotics.com,
        bdong@...obotics.com, manivannanece23@...il.com,
        thomas.liau@...ions-semi.com, jeff.chen@...ions-semi.com
Subject: Re: [PATCH v7 0/6] Add Actions Semiconductor Owl S900 I2C support

On Thu, Jul 26, 2018 at 09:15:57PM +0530, Manivannan Sadhasivam wrote:
> This patchset adds I2C controller support for Actions Semiconductor S900 SoC.
> This driver has been structured in a way such that there will be only
> one controller driver for the whole Owl family series (S500, S700 and
> S900 SoCs).
> 
> There are 6 I2C controllers with separate memory mapped register space.
> The I2C controller can handle atmost two messages concatenated by a
> repeated start via its internal address feature. Hence the driver
> uses this feature for messages of length greater than 1. In those cases,
> the first message of the combined message should be a `write` with maximum
> message length 6 and the second message's maximum length should be 240 bytes.
> 
> As far as the bus speed is concerned, this driver only supports
> Standard (100KHz) and High speed (400KHz) for now.
> 
> The pinctrl definitions are only available for I2C0, I2C1 and I2C2.
> With the mux option available only for I2C0.
> 
> For Bubblegum-96 board utilizing the S900 SoC, only I2C1 and I2C2 which
> are exposed on the Low speed expansion connector are enabled.
> 
> This series depends on the pinctrl patch [1] is still not merged by the
> platform maintainer Andreas but it has been reviewed by the pinctrl maintainer
> Linus Walleij. For the reference, I have queued up all reviewed dts patches
> in my tree [2] from which Andreas is picking them for 4.19.
> 
> For this series, since the dts patches will go through the ARM SoC tree,
> Andreas will pick it up once it is reviewed.
> 
> Thanks,
> Mani
>

Hi Wolfram,

Is there any update on this series?

Thanks,
Mani

> [1] https://patchwork.kernel.org/patch/10322937/
> [2] https://git.linaro.org/people/manivannan.sadhasivam/linux.git/log/?h=s900-for-next
> 
> Changes in v7:
> 
> * Fixed a multi line misalignment spotted by Peter
> 
> Changes in v6:
> 
> As per Peter's review:
> 
> * Added missing newlines for error and debug outputs
> * Fixed further multi-line misalignments
> 
> Changes in v5:
> 
> * Cleaned up the multi-line codes and reordered the error paths
>   as per Peter's review
> * Added Acked-by tag from Peter for driver patch
> * Added Reviewed-by tag from Rob for bindings patch
> 
> Changes in v4:
> 
> As per Andy and Peter review:
> 
> * Used spinlock for accessing most of the register access (only parts
>   involved sleep/long-busy-wait has been excluded)
> * Removed returning 0 and added -ENXIO if the msg_ptr not equals to
>   message length
> * Added DIV_ROUND_UP for setting clock frequency
> * Changed one non-atomic mdelay instance to usleep_range
> * Moved pinctrl definition patch before dts patch
> * Fixed the driver to support only 100KHz and 400KHz frequencies
> 
> Changes in v3:
> 
> As per Peter, Andy and Andreas review:
> 
> * Removed owl_i2c_reset function from interrupt handler since it
>   involves the use of delays.
> * Fixed the return path in owl_i2c_master_xfer and added a note
> * Changed "base" parameter to "reg" in owl_i2c_update_reg for better
>   understandability
> * Ordered the includes in alphabetical order
> * Small changes to defines and added comma at the end of struct members
> * Removed rendundant 0 assignment in owl_i2c_master_xfer
> * Changed all OWL naming convention to Owl and also changed Actions Semi
>   naming to Actions Semiconductor
> 
> Changes in v2:
> 
> As per Andy's review:
> * Modified infinite loops to fixed number of retries
> * Used i2c_8bit_addr_from_msg for constructing the slave address
> * Removed unnecessary parenthesis around defines
> * Modified certain dev_warn to dev_dbg
> * Modified the error handling to more generic pattern
> * Fixed the return value in owl_i2c_master_xfer
> * Added MAINTAINERS patch for I2C driver and its binding
> 
> Manivannan Sadhasivam (6):
>   dt-bindings: i2c: Add binding for Actions Semiconductor Owl I2C
>     controller
>   arm64: dts: actions: Add pinctrl definition for S900 I2C controller
>   arm64: dts: actions: Add Actions Semiconductor S900 I2C controller
>     nodes
>   arm64: dts: actions: Enable I2C1 and I2C2 in Bubblegum-96 board
>   i2c: Add Actions Semiconductor Owl family S900 I2C driver
>   MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
> 
>  .../devicetree/bindings/i2c/i2c-owl.txt       |  27 +
>  MAINTAINERS                                   |   2 +
>  .../dts/actions/s900-bubblegum-96-pins.dtsi   |  29 +
>  .../boot/dts/actions/s900-bubblegum-96.dts    |  11 +
>  arch/arm64/boot/dts/actions/s900.dtsi         |  60 +++
>  drivers/i2c/busses/Kconfig                    |   7 +
>  drivers/i2c/busses/Makefile                   |   1 +
>  drivers/i2c/busses/i2c-owl.c                  | 495 ++++++++++++++++++
>  8 files changed, 632 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/i2c/i2c-owl.txt
>  create mode 100644 arch/arm64/boot/dts/actions/s900-bubblegum-96-pins.dtsi
>  create mode 100644 drivers/i2c/busses/i2c-owl.c
> 
> -- 
> 2.17.1
> 

Powered by blists - more mailing lists