| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20180803085006.flatcfifnnlelruw@M43218.corp.atmel.com>
Date: Fri, 3 Aug 2018 10:50:06 +0200
From: Ludovic Desroches <ludovic.desroches@...rochip.com>
To: Richard Genoud <richard.genoud@...il.com>
CC: <linux-serial@...r.kernel.org>, <linux-arch@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<gregkh@...uxfoundation.org>, <jslaby@...e.com>, <arnd@...db.de>,
<nicolas.ferre@...rochip.com>, <alexandre.belloni@...tlin.com>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2 2/2] tty/serial: atmel: add ISO7816 support
Hi Richard,
On Fri, Jul 27, 2018 at 04:39:17PM +0200, Richard Genoud wrote:
> Hi Ludovic,
>
> On 19/07/2018 10:47, Ludovic Desroches wrote:
> > From: Nicolas Ferre <nicolas.ferre@...rochip.com>
> >
> > When mode is set in atmel_config_iso7816() we backup last RS232 mode
> > for coming back to this mode if requested.
> > Also allow setup of T=0 and T=1 parameter and basic support in set_termios
> > function as well.
> > Report NACK and ITER errors in irq handler.
> >
> > Signed-off-by: Nicolas Ferre <nicolas.ferre@...rochip.com>
> > Signed-off-by: Ludovic Desroches <ludovic.desroches@...rochip.com>
> > ---
> > drivers/tty/serial/atmel_serial.c | 170 +++++++++++++++++++++++++++++++++++---
> > drivers/tty/serial/atmel_serial.h | 3 +-
> > 2 files changed, 162 insertions(+), 11 deletions(-)
> >
> > diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> > index 8e4428725848..cec958f1e7d4 100644
> > --- a/drivers/tty/serial/atmel_serial.c
> > +++ b/drivers/tty/serial/atmel_serial.c
> > @@ -34,6 +34,7 @@
> > #include <linux/suspend.h>
> > #include <linux/mm.h>
> >
> > +#include <asm/div64.h>
> > #include <asm/io.h>
> > #include <asm/ioctls.h>
> >
> > @@ -147,6 +148,8 @@ struct atmel_uart_port {
> > struct circ_buf rx_ring;
> >
> > struct mctrl_gpios *gpios;
> > + u32 backup_mode; /* MR saved during iso7816 operations */
> > + u32 backup_brgr; /* BRGR saved during iso7816 operations */
> > unsigned int tx_done_mask;
> > u32 fifo_size;
> > u32 rts_high;
> > @@ -362,6 +365,132 @@ static int atmel_config_rs485(struct uart_port *port,
> > return 0;
> > }
> >
> > +static unsigned int atmel_calc_cd(struct uart_port *port,
> > + struct serial_iso7816 *iso7816conf)
> > +{
> > + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> > + unsigned int cd;
> > + u64 mck_rate;
> > +
> > + mck_rate = (u64)clk_get_rate(atmel_port->clk);
> > + do_div(mck_rate, iso7816conf->clk);
> > + cd = mck_rate;
> > + return cd;
> > +}
> > +
> > +static unsigned int atmel_calc_fidi(struct uart_port *port,
> > + struct serial_iso7816 *iso7816conf)
> > +{
> > + u64 fidi = 0;
> > +
> > + if (iso7816conf->sc_fi && iso7816conf->sc_di) {
> > + fidi = (u64)iso7816conf->sc_fi;
> > + do_div(fidi, iso7816conf->sc_di);
> > + }
> > + return (u32)fidi;
> > +}
> > +
> > +/* Enable or disable the iso7816 support */
> > +/* Called with interrupts disabled */
> > +static int atmel_config_iso7816(struct uart_port *port,
> > + struct serial_iso7816 *iso7816conf)
> > +{
> > + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> > + unsigned int mode, t;
> > + unsigned int cd, fidi;
> > + int ret = 0;
> > +
> > + /* Disable RX and TX */
> > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS | ATMEL_US_TXDIS);
> > + /* Disable interrupts */
> > + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
> > +
> > + mode = atmel_uart_readl(port, ATMEL_US_MR);
> > +
> > + if (iso7816conf->flags & SER_ISO7816_ENABLED) {
> > + mode &= ~ATMEL_US_USMODE;
> > +
> > + if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
> > + == SER_ISO7816_T(0)) {
> > + mode |= ATMEL_US_USMODE_ISO7816_T0;
> > + t = 0;
> > + } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
> > + == SER_ISO7816_T(1)) {
> > + mode |= ATMEL_US_USMODE_ISO7816_T1;
> > + t = 1;
> > + } else {
> > + dev_warn(port->dev, "ISO7816 Type not supported. Resetting\n");
> > + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> > + goto err_out;
> > + }
> > +
> > + dev_dbg(port->dev, "Setting USART to ISO7816 mode T%d\n", t);
> > +
> > + mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
> > + | ATMEL_US_NBSTOP | ATMEL_US_PAR);
> This could be merged in the mode &= line above.
>
Ok
> > +
> > + /* NACK configuration */
> > + if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
> > + == SER_ISO7816_T(0))
> > + mode |= ATMEL_US_DSNACK;
> > + else
> > + mode |= ATMEL_US_INACK;
> This could be also part of the if () above.
>
Ok
> > + /* select mck clock, and output */
> > + mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
> > + /* set parity for normal/inverse mode + max iterations */
> > + mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | (3 << 24);
> Is this really needed ?
> In the documentation, I found:
> "The configuration is 8 data bits, even parity and 1 or 2 stop bits,
> regardless of the values programmed in the CHRL, MODE9, PAR and CHMODE
> fields."
It's not very clear. It is followed by "Parity Bit (PAR) can be used to
transmit in Normal or Inverse mode." and you have to choose 1 or 2 stop
bits.
> And, for MAX_ITERATIONS, could you add a macro instead of (x << 24) ?
> (ATMEL_US_MAX_ITER mask is already defined).
Yes
> And why 3 ? Should the user-space be allowed to control the max
> automatic iteration ? or is it more like a "same-value-for-every-one"
> thing ?
>
It's an arbitrary choice. I have not seen any reference to number of
repetition in the ISO7816 spec but I may miss it. So I would say it's
not the same value for everyone. Is it useful to let the user setting
it? I don't know, maybe we can wait for a request to export this
setting.
> > +
> > + cd = atmel_calc_cd(port, iso7816conf);
> > + fidi = atmel_calc_fidi(port, iso7816conf);
> > + if (fidi < 0) {
> I guess you meant (fidi == 0)
> Because fidi is unsigned and atmel_calc_fidi() returns also an unsigned.
Right.
>
> > + dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
> > + } else if (fidi == 1 || fidi == 2) {
> > + dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
> > + ret = -EINVAL;
> > + goto err_out;
> > + }
> And you may also want to check upper values ( <2048 or <65536, depending
> on the SoC)
>
I'll do, I assumed that user space won't request weird values but it's
probably better to not trust him.
> > +
> > + if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
> > + /* port not yet in iso7816 mode: store configuration */
> > + atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
> > + atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
> > + }
> > +
> > + /* Actually set ISO7816 mode */
> > + atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
> iso7816conf->tg comes from user-space unchecked. AFAIK, max value is 255
Ok I'll check it.
>
> > + atmel_uart_writel(port, ATMEL_US_BRGR, cd);
> > + atmel_uart_writel(port, ATMEL_US_FIDIR, fidi);
> > +
> > + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
> > + } else {
> > + dev_dbg(port->dev, "Setting UART to RS232\n");
> > + /* back to last RS232 settings */
> > + mode = atmel_port->backup_mode;
> > + memset(iso7816conf, 0, sizeof(struct serial_iso7816));
> > + atmel_uart_writel(port, ATMEL_US_TTGR, 0);
> > + atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
> > + atmel_uart_writel(port, ATMEL_US_FIDIR, 0x174);
> > +
> > + if (atmel_use_pdc_tx(port))
> > + atmel_port->tx_done_mask = ATMEL_US_ENDTX |
> > + ATMEL_US_TXBUFE;
> > + else
> > + atmel_port->tx_done_mask = ATMEL_US_TXRDY;
> > + }
> > +
> > + port->iso7816 = *iso7816conf;
> > +
> > + atmel_uart_writel(port, ATMEL_US_MR, mode);
> > +
> > +err_out:
> > + /* Enable interrupts */
> > + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
> > + /* Enable RX and TX */
> > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN | ATMEL_US_TXEN);
> Is it all right to enable RX/TX unconditionally here ?
>
As I didn't see any issue at the moment, I kept it like this. But I have
noticed this warning in the datasheet and I keep it in mind:
"Enabling both the receiver and the transmitter at the same time in
ISO7816 mode maylead to unpredictable results"
> > +
> > + return ret;
> > +}
> > +
> > /*
> > * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
> > */
> > @@ -481,8 +610,9 @@ static void atmel_stop_tx(struct uart_port *port)
> > /* Disable interrupts */
> > atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
> >
> > - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> > - !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> > + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> > + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> > + port->iso7816.flags & SER_ISO7816_ENABLED)
> > atmel_start_rx(port);
> > }
> >
> > @@ -500,8 +630,9 @@ static void atmel_start_tx(struct uart_port *port)
> > return;
> >
> > if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
> > - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> > - !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> > + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> > + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> > + port->iso7816.flags & SER_ISO7816_ENABLED)
> > atmel_stop_rx(port);
> >
> > if (atmel_use_pdc_tx(port))
> > @@ -799,8 +930,9 @@ static void atmel_complete_tx_dma(void *arg)
> > */
> > if (!uart_circ_empty(xmit))
> > atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
> > - else if ((port->rs485.flags & SER_RS485_ENABLED) &&
> > - !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
> > + else if (((port->rs485.flags & SER_RS485_ENABLED) &&
> > + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> > + port->iso7816.flags & SER_ISO7816_ENABLED) {
> > /* DMA done, stop TX, start RX for RS485 */
> > atmel_start_rx(port);
> > }
> > @@ -1281,6 +1413,9 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
> > wake_up_interruptible(&port->state->port.delta_msr_wait);
> > }
> > }
> > +
> > + if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
> > + dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
> > }
> >
> > /*
> > @@ -1373,8 +1508,9 @@ static void atmel_tx_pdc(struct uart_port *port)
> > atmel_uart_writel(port, ATMEL_US_IER,
> > atmel_port->tx_done_mask);
> > } else {
> > - if ((port->rs485.flags & SER_RS485_ENABLED) &&
> > - !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
> > + if (((port->rs485.flags & SER_RS485_ENABLED) &&
> > + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
> > + port->iso7816.flags & SER_ISO7816_ENABLED) {
> > /* DMA done, stop TX, start RX for RS485 */
> > atmel_start_rx(port);
> > }
> > @@ -2099,6 +2235,17 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> > atmel_uart_writel(port, ATMEL_US_TTGR,
> > port->rs485.delay_rts_after_send);
> > mode |= ATMEL_US_USMODE_RS485;
> > + } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
> > + atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
> > + /* select mck clock, and output */
> > + mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
> > + /* set max iterations */
> > + mode |= (3 << 24);
> Same remark for macro / hardcoded value.
>
OK
> > + if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
> > + == SER_ISO7816_T(0))
> > + mode |= ATMEL_US_USMODE_ISO7816_T0;
> > + else
> > + mode |= ATMEL_US_USMODE_ISO7816_T1;
> > } else if (termios->c_cflag & CRTSCTS) {
> > /* RS232 with hardware handshake (RTS/CTS) */
> > if (atmel_use_fifo(port) &&
> > @@ -2175,7 +2322,8 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> > }
> > quot = cd | fp << ATMEL_US_FP_OFFSET;
> >
> > - atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> > + if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
> > + atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> > atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> > atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
> > atmel_port->tx_stopped = false;
> > @@ -2355,6 +2503,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> > port->mapbase = pdev->resource[0].start;
> > port->irq = pdev->resource[1].start;
> > port->rs485_config = atmel_config_rs485;
> > + port->iso7816_config = atmel_config_iso7816;
> > port->membase = NULL;
> >
> > memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
> > @@ -2379,7 +2528,8 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> > }
> >
> > /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
> > - if (port->rs485.flags & SER_RS485_ENABLED)
> > + if (port->rs485.flags & SER_RS485_ENABLED ||
> > + port->iso7816.flags & SER_ISO7816_ENABLED)
> please update the comment above.
>
OK
> > atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
> > else if (atmel_use_pdc_tx(port)) {
> > port->fifosize = PDC_BUFFER_SIZE;
> > diff --git a/drivers/tty/serial/atmel_serial.h b/drivers/tty/serial/atmel_serial.h
> > index ba3a2437cde4..fff51f5fe8bc 100644
> > --- a/drivers/tty/serial/atmel_serial.h
> > +++ b/drivers/tty/serial/atmel_serial.h
> > @@ -124,7 +124,8 @@
> > #define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
> > #define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
> >
> > -#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
> > +#define ATMEL_US_FIDIR 0x40 /* FI DI Ratio Register */
> > +#define ATMEL_US_FIDI GENMASK(15, 0) /* FIDI ratio */
> > #define ATMEL_US_NER 0x44 /* Number of Errors Register */
> > #define ATMEL_US_IF 0x4c /* IrDA Filter Register */
> >
> >
>
> Thanks !
>
> Richard.
Thanks for your review, I'll send a new version.
Regards
Ludovic
Powered by blists - more mailing lists