Message-ID: <1534403190-28523-7-git-send-email-jliang@xilinx.com>
Date:   Thu, 16 Aug 2018 00:06:29 -0700
From:   Wendy Liang <wendy.liang@...inx.com>
To:     <ohad@...ery.com>, <bjorn.andersson@...aro.org>,
        <michal.simek@...inx.com>, <robh+dt@...nel.org>,
        <mark.rutland@....com>, <rajan.vaja@...inx.com>,
        <jollys@...inx.com>
CC:     <linux-remoteproc@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        Wendy Liang <jliang@...inx.com>
Subject: [PATCH 6/7] remoteproc: Add Xilinx ZynqMP R5 remoteproc

There are cortex-r5 processors in Xilinx Zynq UltraScale+
MPSoC platforms. This remoteproc driver is to manage the
R5 processors.

Signed-off-by: Wendy Liang <jliang@...inx.com>
---
 drivers/remoteproc/Kconfig                |   9 +
 drivers/remoteproc/Makefile               |   1 +
 drivers/remoteproc/zynqmp_r5_remoteproc.c | 692 ++++++++++++++++++++++++++++++
 3 files changed, 702 insertions(+)
 create mode 100644 drivers/remoteproc/zynqmp_r5_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index cd1c168..83aac63 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -158,6 +158,15 @@ config ST_REMOTEPROC
 config ST_SLIM_REMOTEPROC
 	tristate
 
+config ZYNQMP_R5_REMOTEPROC
+	tristate "ZynqMP_r5 remoteproc support"
+	depends on ARM64 && PM && ARCH_ZYNQMP
+	select RPMSG_VIRTIO
+	select ZYNQMP_FIRMWARE
+	help
+	  Say y here to support ZynqMP R5 remote processors via the remote
+	  processor framework.
+
 endif # REMOTEPROC
 
 endmenu
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index 02627ed..147923c 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -23,3 +23,4 @@ qcom_wcnss_pil-y			+= qcom_wcnss.o
 qcom_wcnss_pil-y			+= qcom_wcnss_iris.o
 obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
 obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
+obj-$(CONFIG_ZYNQMP_R5_REMOTEPROC)	+= zynqmp_r5_remoteproc.o
diff --git a/drivers/remoteproc/zynqmp_r5_remoteproc.c b/drivers/remoteproc/zynqmp_r5_remoteproc.c
new file mode 100644
index 0000000..7fc3718
--- /dev/null
+++ b/drivers/remoteproc/zynqmp_r5_remoteproc.c
@@ -0,0 +1,692 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Zynq R5 Remote Processor driver
+ *
+ * Copyright (C) 2015 Xilinx, Inc.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/remoteproc.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/slab.h>
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/list.h>
+#include <linux/genalloc.h>
+#include <linux/pfn.h>
+#include <linux/idr.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+#include "remoteproc_internal.h"
+
+/* IPI reg offsets */
+#define TRIG_OFFSET		0x00000000
+#define OBS_OFFSET		0x00000004
+#define ISR_OFFSET		0x00000010
+#define IMR_OFFSET		0x00000014
+#define IER_OFFSET		0x00000018
+#define IDR_OFFSET		0x0000001C
+#define IPI_ALL_MASK		0x0F0F0301
+
+/* RPU IPI mask */
+#define RPU_IPI_INIT_MASK	0x00000100
+#define RPU_IPI_MASK(n)		(RPU_IPI_INIT_MASK << (n))
+#define RPU_0_IPI_MASK		RPU_IPI_MASK(0)
+#define RPU_1_IPI_MASK		RPU_IPI_MASK(1)
+
+/* PM proc states */
+#define PM_PROC_STATE_ACTIVE 1u
+
+/* Maximum TCM power nodes IDs */
+#define MAX_TCM_PNODES 4
+
+/* Register access macros */
+#define reg_read(base, reg) \
+	readl(((void __iomem *)(base)) + (reg))
+#define reg_write(base, reg, val) \
+	writel((val), ((void __iomem *)(base)) + (reg))
+
+#define DEFAULT_FIRMWARE_NAME	"rproc-rpu-fw"
+
+static bool autoboot __read_mostly;
+
+struct zynqmp_r5_rproc_pdata;
+
+/**
+ * struct zynqmp_r5_rproc_pdata - zynqmp rpu remote processor instance state
+ * @rproc: rproc handle
+ * @workqueue: workqueue for the RPU remoteproc
+ * @ipi_base: virt ptr to IPI channel address registers for APU
+ * @rpu_mode: RPU core configuration
+ * @rpu_id: RPU CPU id
+ * @rpu_pnode_id: RPU CPU power domain id
+ * @mem_pools: list of gen_pool for firmware mmio_sram memory and their
+ *             power domain IDs
+ * @mems: list of rproc_mem_entries for firmware
+ * @irq: IRQ number
+ * @ipi_dest_mask: IPI destination mask for the IPI channel
+ */
+struct zynqmp_r5_rproc_pdata {
+	struct rproc *rproc;
+	struct work_struct workqueue;
+	void __iomem *ipi_base;
+	enum rpu_oper_mode rpu_mode;
+	struct list_head mems;
+	u32 ipi_dest_mask;
+	u32 rpu_id;
+	u32 rpu_pnode_id;
+	int irq;
+	u32 tcm_pnode_id[MAX_TCM_PNODES];
+};
+
+/**
+ * r5_boot_addr_config - configure the boot address of R5
+ * @pdata: platform data
+ * @bootmem: boot from LOVEC or HIVEC
+ *
+ * This function will set the RPU boot address
+ */
+static void r5_boot_addr_config(struct zynqmp_r5_rproc_pdata *pdata,
+				enum rpu_boot_mem bootmem)
+{
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+
+	pr_debug("%s: R5 ID: %d, boot_dev %d\n",
+		 __func__, pdata->rpu_id, bootmem);
+
+	if (!eemi || !eemi->ioctl) {
+		pr_err("%s: no eemi ioctl operation.\n", __func__);
+		return;
+	}
+	eemi->ioctl(pdata->rpu_pnode_id, IOCTL_RPU_BOOT_ADDR_CONFIG,
+		    bootmem, 0, NULL);
+}
+
+/**
+ * r5_mode_config - configure R5 operation mode
+ * @pdata: platform data
+ *
+ * configure R5 to split mode or lockstep mode
+ * based on the platform data.
+ */
+static void r5_mode_config(struct zynqmp_r5_rproc_pdata *pdata)
+{
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+
+	pr_debug("%s: mode: %d\n", __func__, pdata->rpu_mode);
+
+	if (!eemi || !eemi->ioctl) {
+		pr_err("%s: no eemi ioctl operation.\n", __func__);
+		return;
+	}
+	eemi->ioctl(pdata->rpu_pnode_id, IOCTL_SET_RPU_OPER_MODE,
+		    pdata->rpu_mode, 0, NULL);
+}
+
+/**
+ * r5_release_tcm() - release TCM
+ * @pdata: platform data
+ *
+ * Release TCM
+ */
+static void r5_release_tcm(struct zynqmp_r5_rproc_pdata *pdata)
+{
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+	int i;
+
+	if (!eemi || !eemi->release_node) {
+		pr_err("Failed to release TCM\n");
+		return;
+	}
+
+	for (i = 0; i < MAX_TCM_PNODES; i++) {
+		if (pdata->tcm_pnode_id[i] != 0)
+			eemi->release_node(pdata->tcm_pnode_id[i]);
+	}
+}
+
+/**
+ * disable_ipi - disable IPI
+ * @pdata: platform data
+ *
+ * Disable IPI interrupt
+ */
+static inline void disable_ipi(struct zynqmp_r5_rproc_pdata *pdata)
+{
+	/* Disable R5 IPI interrupt */
+	if (pdata->ipi_base)
+		reg_write(pdata->ipi_base, IDR_OFFSET, pdata->ipi_dest_mask);
+}
+
+/**
+ * enable_ipi - enable IPI
+ * @pdata: platform data
+ *
+ * Enable IPI interrupt
+ */
+static inline void enable_ipi(struct zynqmp_r5_rproc_pdata *pdata)
+{
+	/* Enable R5 IPI interrupt */
+	if (pdata->ipi_base)
+		reg_write(pdata->ipi_base, IER_OFFSET, pdata->ipi_dest_mask);
+}
+
+/**
+ * event_notified_idr_cb - event notified idr callback
+ * @id: idr id
+ * @ptr: pointer to idr private data
+ * @data: data passed to idr_for_each callback
+ *
+ * Pass notification to remoteproc virtio
+ *
+ * @return: 0. having return is to satisfy the idr_for_each() function
+ *          pointer input argument requirement.
+ */
+static int event_notified_idr_cb(int id, void *ptr, void *data)
+{
+	struct rproc *rproc = data;
+
+	(void)rproc_vq_interrupt(rproc, id);
+	return 0;
+}
+
+static void handle_event_notified(struct work_struct *work)
+{
+	struct rproc *rproc;
+	struct zynqmp_r5_rproc_pdata *local;
+
+	local = container_of(work, struct zynqmp_r5_rproc_pdata, workqueue);
+	rproc = local->rproc;
+	idr_for_each(&rproc->notifyids, event_notified_idr_cb, rproc);
+}
+
+static int zynqmp_r5_rproc_start(struct rproc *rproc)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+	enum rpu_boot_mem bootmem;
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	if (!eemi || !eemi->force_powerdown ||
+	    !eemi->request_wakeup) {
+		pr_err("Failed to start R5\n");
+		return -ENXIO;
+	}
+
+	/* Set up R5 */
+	if ((rproc->bootaddr & 0xF0000000) == 0xF0000000)
+		bootmem = PM_RPU_BOOTMEM_HIVEC;
+	else
+		bootmem = PM_RPU_BOOTMEM_LOVEC;
+	dev_info(dev, "RPU boot from %s.",
+		 bootmem == PM_RPU_BOOTMEM_HIVEC ? "OCM" : "TCM");
+
+	r5_mode_config(local);
+	eemi->force_powerdown(local->rpu_pnode_id,
+			      ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+	r5_boot_addr_config(local, bootmem);
+	/* Add delay before release from halt and reset */
+	usleep_range(400, 500);
+	eemi->request_wakeup(local->rpu_pnode_id,
+			     1, bootmem,
+			     ZYNQMP_PM_REQUEST_ACK_NO);
+
+	/* Make sure IPI is enabled */
+	enable_ipi(local);
+
+	return 0;
+}
+
+/* kick a firmware */
+static void zynqmp_r5_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+
+	dev_dbg(dev, "KICK Firmware to start send messages vqid %d\n", vqid);
+
+	/*
+	 * send irq to R5 firmware
+	 * Currently vqid is not used because we only got one.
+	 */
+	if (local->ipi_base)
+		reg_write(local->ipi_base, TRIG_OFFSET, local->ipi_dest_mask);
+}
+
+/* power off the remote processor */
+static int zynqmp_r5_rproc_stop(struct rproc *rproc)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+	struct rproc_mem_entry *mem, *nmem;
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	if (!eemi || !eemi->force_powerdown) {
+		pr_err("Failed to stop R5\n");
+		return -ENXIO;
+	}
+
+	disable_ipi(local);
+	eemi->force_powerdown(local->rpu_pnode_id,
+			      ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+
+	return 0;
+}
+
+static void *zynqmp_r5_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
+{
+	struct rproc_mem_entry *mem;
+	void *va = NULL;
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+
+	list_for_each_entry(mem, &local->mems, node) {
+		int offset = da - mem->da;
+
+		/* try next carveout if da is too small */
+		if (offset < 0)
+			continue;
+
+		/* try next carveout if da is too large */
+		if (offset + len > mem->len)
+			continue;
+
+		va = mem->va + offset;
+
+		break;
+	}
+	return va;
+}
+
+static int zynqmp_r5_parse_fw(struct rproc *rproc, const struct firmware *fw)
+{
+	int ret;
+
+	ret = rproc_elf_load_rsc_table(rproc, fw);
+	if (ret == -EINVAL)
+		/* No resource table */
+		return 0;
+	else
+		return ret;
+}
+
+static struct rproc_ops zynqmp_r5_rproc_ops = {
+	.start		= zynqmp_r5_rproc_start,
+	.stop		= zynqmp_r5_rproc_stop,
+	.kick		= zynqmp_r5_rproc_kick,
+	.da_to_va       = zynqmp_r5_rproc_da_to_va,
+};
+
+/* Release R5 from reset and make it halted.
+ * In case the firmware uses TCM, in order to load firmware to TCM,
+ * will need to release R5 from reset and stay in halted state.
+ */
+static int zynqmp_r5_rproc_init(struct rproc *rproc)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+
+	dev_dbg(dev, "%s\n", __func__);
+	enable_ipi(local);
+	return 0;
+}
+
+static irqreturn_t r5_remoteproc_interrupt(int irq, void *dev_id)
+{
+	struct device *dev = dev_id;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct rproc *rproc = platform_get_drvdata(pdev);
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+	u32 ipi_reg;
+
+	/* Check if there is a kick from R5 */
+	ipi_reg = reg_read(local->ipi_base, ISR_OFFSET);
+	if (!(ipi_reg & local->ipi_dest_mask))
+		return IRQ_NONE;
+
+	dev_dbg(dev, "KICK Linux because of pending message(irq%d)\n", irq);
+	reg_write(local->ipi_base, ISR_OFFSET, local->ipi_dest_mask);
+	schedule_work(&local->workqueue);
+
+	return IRQ_HANDLED;
+}
+
+/* zynqmp_r5_get_tcm_memories() - get tcm memories
+ * @pdev: pointer to the platform device
+ * @pdata: pointer to the remoteproc private data
+ *
+ * Function to create remoteproc memory entries for TCM memories.
+ */
+static int zynqmp_r5_get_tcms(struct platform_device *pdev,
+			      struct zynqmp_r5_rproc_pdata *pdata)
+{
+	static const char * const mem_names[] = {"tcm_a", "tcm_b"};
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int num_mems = 0;
+	int i, ret;
+	struct property *prop;
+	const __be32 *cur;
+	u32 val;
+	const struct zynqmp_eemi_ops *eemi = zynqmp_pm_get_eemi_ops();
+
+	/* Get TCM power node ids */
+	i = 0;
+	of_property_for_each_u32(np, "tcm-pnode-id", prop, cur, val)
+		pdata->tcm_pnode_id[i++] = val;
+
+	/* Request TCMs */
+	for (i = 0; i < MAX_TCM_PNODES; i++) {
+		if (pdata->tcm_pnode_id[i] != 0) {
+			ret = eemi->request_node(pdata->tcm_pnode_id[i],
+						 ZYNQMP_PM_CAPABILITY_ACCESS, 0,
+						 ZYNQMP_PM_REQUEST_ACK_BLOCKING
+						);
+			if (ret < 0) {
+				dev_err(dev, "failed to request TCM: %u\n",
+					pdata->tcm_pnode_id[i]);
+				return ret;
+			}
+			dev_dbg(dev, "request tcm pnode: %u\n",
+				pdata->tcm_pnode_id[i]);
+		} else {
+			break;
+		}
+	}
+	/* Create remoteproc memories entries for TCM memories */
+	num_mems = ARRAY_SIZE(mem_names);
+	for (i = 0; i < num_mems; i++) {
+		struct resource *res;
+		struct rproc_mem_entry *mem;
+		dma_addr_t dma;
+		resource_size_t size;
+
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   mem_names[i]);
+		mem  = devm_kzalloc(dev, sizeof(struct rproc_mem_entry),
+				    GFP_KERNEL);
+		if (!mem)
+			return -ENOMEM;
+		/* Map it as normal memory */
+		size = resource_size(res);
+		mem->va = devm_ioremap_wc(dev, res->start, size);
+		mem->len = size;
+		dma = (dma_addr_t)res->start;
+		mem->dma = dma;
+		/* TCM memory:
+		 *   TCM_0: da 0 <-> global addr 0xFFE00000
+		 *   TCM_1: da 0 <-> global addr 0xFFE90000
+		 */
+		if ((dma & 0xFFF00000) == 0xFFE00000) {
+			if ((dma & 0xFFF80000) == 0xFFE80000)
+				mem->da -= 0x90000;
+			else
+				mem->da = (dma & 0x000FFFFF);
+		}
+		dev_dbg(dev, "%s: va = %p, da = 0x%x dma = 0x%llx\n",
+			__func__, mem->va, mem->da, mem->dma);
+		list_add_tail(&mem->node, &pdata->mems);
+	}
+	return 0;
+}
+
+/* zynqmp_r5_get_reserved_mems() - get reserved memories
+ * @pdev: pointer to the platform device
+ * @pdata: pointer to the remoteproc private data
+ *
+ * Function to create remoteproc memory entries from memory-region
+ * property.
+ */
+static int zynqmp_r5_get_reserved_mems(struct platform_device *pdev,
+				       struct zynqmp_r5_rproc_pdata *pdata)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int num_mems;
+	int i;
+
+	num_mems = of_count_phandle_with_args(np, "memory-region", NULL);
+	if (num_mems <= 0)
+		return 0;
+	for (i = 0; i < num_mems; i++) {
+		struct device_node *node;
+		struct resource res;
+		resource_size_t size;
+		struct rproc_mem_entry *mem;
+		int ret;
+
+		node = of_parse_phandle(np, "memory-region", i);
+		ret = of_device_is_compatible(node, "rproc-prog-memory");
+		if (!ret) {
+			/* it is DMA memory. */
+			dev_info(dev, "%s, dma memory %d\n", __func__, i);
+			ret = of_reserved_mem_device_init_by_idx(dev,
+								 np, i);
+			if (ret) {
+				dev_err(dev, "unable to reserve DMA mem.\n");
+				return ret;
+			}
+			continue;
+		}
+		ret = of_address_to_resource(node, 0, &res);
+		if (ret) {
+			dev_err(dev, "unable to resolve memory region.\n");
+			return ret;
+		}
+		mem  = devm_kzalloc(dev, sizeof(struct rproc_mem_entry),
+				    GFP_KERNEL);
+		if (!mem)
+			return -ENOMEM;
+		/* Map it as normal memory */
+		size = resource_size(&res);
+		mem->va = devm_ioremap_wc(dev, res.start, size);
+		mem->len = size;
+		mem->dma = (dma_addr_t)res.start;
+		mem->da = (u32)res.start;
+		dev_dbg(dev, "%s: va = %p, da = 0x%x dma = 0x%llx\n",
+			__func__, mem->va, mem->da, mem->dma);
+		list_add_tail(&mem->node, &pdata->mems);
+	}
+	return 0;
+}
+
+static int zynqmp_r5_remoteproc_probe(struct platform_device *pdev)
+{
+	const unsigned char *prop;
+	struct resource *res;
+	int ret = 0;
+	struct zynqmp_r5_rproc_pdata *local;
+	struct rproc *rproc;
+
+	rproc = rproc_alloc(&pdev->dev, dev_name(&pdev->dev),
+			    &zynqmp_r5_rproc_ops, NULL,
+		sizeof(struct zynqmp_r5_rproc_pdata));
+	if (!rproc) {
+		dev_err(&pdev->dev, "rproc allocation failed\n");
+		return -ENOMEM;
+	}
+	local = rproc->priv;
+	local->rproc = rproc;
+
+	platform_set_drvdata(pdev, rproc);
+
+	/* Override parse_fw op to allow no resource table firmware */
+	rproc->ops->parse_fw = zynqmp_r5_parse_fw;
+
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(&pdev->dev, "dma_set_coherent_mask: %d\n", ret);
+		goto rproc_fault;
+	}
+
+	/* Get the RPU power domain id */
+	ret = of_property_read_u32(pdev->dev.of_node, "rpu-pnode-id",
+				   &local->rpu_pnode_id);
+	if (ret) {
+		dev_err(&pdev->dev, "No RPU power node ID is specified.\n");
+		ret = -EINVAL;
+		goto rproc_fault;
+	}
+	dev_dbg(&pdev->dev, "RPU[%d] pnode_id = %d.\n",
+		local->rpu_id, local->rpu_pnode_id);
+
+	prop = of_get_property(pdev->dev.of_node, "core_conf", NULL);
+	if (!prop) {
+		dev_warn(&pdev->dev, "default core_conf used: lock-step\n");
+		prop = "lock-step";
+	}
+
+	dev_info(&pdev->dev, "RPU core_conf: %s\n", prop);
+	if (!strcmp(prop, "split0")) {
+		local->rpu_mode = PM_RPU_MODE_SPLIT;
+		local->rpu_id = 0;
+		local->ipi_dest_mask = RPU_0_IPI_MASK;
+	} else if (!strcmp(prop, "split1")) {
+		local->rpu_mode = PM_RPU_MODE_SPLIT;
+		local->rpu_id = 1;
+		local->ipi_dest_mask = RPU_1_IPI_MASK;
+	} else if (!strcmp(prop, "lock-step")) {
+		local->rpu_mode = PM_RPU_MODE_LOCKSTEP;
+		local->rpu_id = 0;
+		local->ipi_dest_mask = RPU_0_IPI_MASK;
+	} else {
+		dev_err(&pdev->dev, "Invalid core_conf mode provided - %s , %d\n",
+			prop, local->rpu_mode);
+		ret = -EINVAL;
+		goto rproc_fault;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ipi");
+	if (res) {
+		local->ipi_base = devm_ioremap(&pdev->dev, res->start,
+					       resource_size(res));
+		if (IS_ERR(local->ipi_base)) {
+			pr_err("%s: Unable to map IPI\n", __func__);
+			ret = PTR_ERR(local->ipi_base);
+			goto rproc_fault;
+		}
+	} else {
+		dev_info(&pdev->dev, "IPI resource is not specified.\n");
+	}
+	dev_dbg(&pdev->dev, "got ipi base address\n");
+
+	INIT_LIST_HEAD(&local->mems);
+	/* Get TCM memories */
+	ret = zynqmp_r5_get_tcms(pdev, local);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to get TCM memories.\n");
+		goto rproc_fault;
+	}
+	dev_dbg(&pdev->dev, "got TCM memories\n");
+	/* Get reserved memory regions for firmware */
+	ret = zynqmp_r5_get_reserved_mems(pdev, local);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to get reserved memories.\n");
+		goto rproc_fault;
+	}
+	dev_dbg(&pdev->dev, "got reserved memories.\n");
+
+	/* Disable IPI before requesting IPI IRQ */
+	disable_ipi(local);
+	INIT_WORK(&local->workqueue, handle_event_notified);
+
+	/* IPI IRQ */
+	if (local->ipi_base) {
+		ret = platform_get_irq(pdev, 0);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "unable to find IPI IRQ\n");
+			goto rproc_fault;
+		}
+		local->irq = ret;
+		ret = devm_request_irq(&pdev->dev, local->irq,
+				       r5_remoteproc_interrupt, IRQF_SHARED,
+				       dev_name(&pdev->dev), &pdev->dev);
+		if (ret) {
+			dev_err(&pdev->dev, "IRQ %d already allocated\n",
+				local->irq);
+			goto rproc_fault;
+		}
+		dev_dbg(&pdev->dev, "notification irq: %d\n", local->irq);
+	}
+
+	ret = zynqmp_r5_rproc_init(local->rproc);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to init ZynqMP R5 rproc\n");
+		goto rproc_fault;
+	}
+
+	rproc->auto_boot = autoboot;
+
+	ret = rproc_add(local->rproc);
+	if (ret) {
+		dev_err(&pdev->dev, "rproc registration failed\n");
+		goto rproc_fault;
+	}
+
+	return ret;
+
+rproc_fault:
+	rproc_free(local->rproc);
+
+	return ret;
+}
+
+static int zynqmp_r5_remoteproc_remove(struct platform_device *pdev)
+{
+	struct rproc *rproc = platform_get_drvdata(pdev);
+	struct zynqmp_r5_rproc_pdata *local = rproc->priv;
+	struct rproc_mem_entry *mem;
+
+	dev_info(&pdev->dev, "%s\n", __func__);
+
+	rproc_del(rproc);
+
+	list_for_each_entry(mem, &local->mems, node) {
+		if (mem->priv)
+			gen_pool_free((struct gen_pool *)mem->priv,
+				      (unsigned long)mem->va, mem->len);
+	}
+
+	r5_release_tcm(local);
+	of_reserved_mem_device_release(&pdev->dev);
+	rproc_free(rproc);
+
+	return 0;
+}
+
+/* Match table for OF platform binding */
+static const struct of_device_id zynqmp_r5_remoteproc_match[] = {
+	{ .compatible = "xlnx,zynqmp-r5-remoteproc-1.0", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, zynqmp_r5_remoteproc_match);
+
+static struct platform_driver zynqmp_r5_remoteproc_driver = {
+	.probe = zynqmp_r5_remoteproc_probe,
+	.remove = zynqmp_r5_remoteproc_remove,
+	.driver = {
+		.name = "zynqmp_r5_remoteproc",
+		.of_match_table = zynqmp_r5_remoteproc_match,
+	},
+};
+module_platform_driver(zynqmp_r5_remoteproc_driver);
+
+module_param_named(autoboot,  autoboot, bool, 0444);
+MODULE_PARM_DESC(autoboot,
+		 "enable | disable autoboot. (default: true)");
+
+MODULE_AUTHOR("Jason Wu <j.wu@...inx.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("ZynqMP R5 remote processor control driver");
-- 
2.7.4

Powered by blists - more mailing lists