linux-kernel - [PATCH V2 22/27] mmc: mmci: add variant property to not read datacnt

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1537268144-21152-23-git-send-email-ludovic.Barre@st.com>
Date:   Tue, 18 Sep 2018 12:55:39 +0200
From:   Ludovic Barre <ludovic.Barre@...com>
To:     Ulf Hansson <ulf.hansson@...aro.org>,
        Rob Herring <robh+dt@...nel.org>
CC:     Maxime Coquelin <mcoquelin.stm32@...il.com>,
        Alexandre Torgue <alexandre.torgue@...com>,
        <benjamin.gaignard@...aro.org>, Gerald Baeza <gerald.baeza@...com>,
        Loic Pallardy <loic.pallardy@...com>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-mmc@...r.kernel.org>,
        <linux-stm32@...md-mailman.stormreply.com>,
        Ludovic Barre <ludovic.barre@...com>
Subject: [PATCH V2 22/27] mmc: mmci: add variant property to not read datacnt

From: Ludovic Barre <ludovic.barre@...com>

This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.

Signed-off-by: Ludovic Barre <ludovic.barre@...com>
---
 drivers/mmc/host/mmci.c | 8 ++++++--
 drivers/mmc/host/mmci.h | 3 +++
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index b525ba4..b1d5bc5 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1095,8 +1095,12 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 		 * can be as much as a FIFO-worth of data ahead.  This
 		 * matters for FIFO overruns only.
 		 */
-		remain = readl(host->base + MMCIDATACNT);
-		success = data->blksz * data->blocks - remain;
+		if (!host->variant->datacnt_useless) {
+			remain = readl(host->base + MMCIDATACNT);
+			success = data->blksz * data->blocks - remain;
+		} else {
+			success = 0;
+		}
 
 		dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n",
 			status_err, success);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 89e6733..7fd89b7 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -224,6 +224,8 @@ struct mmci_host;
  * @datactrl_blksz: block size in power of two
  * @datactrl_dpsm_enable: enable value for DPSM
  * @datactrl_first: true if data must be setup before send command
+ * @datacnt_useless: true if you could not use datacnt register to read
+ *		     remaining data
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -264,6 +266,7 @@ struct variant_data {
 	unsigned int		datactrl_blocksz;
 	unsigned int		datactrl_dpsm_enable;
 	bool			datactrl_first;
+	bool			datacnt_useless;
 	bool			st_sdio;
 	bool			st_clkdiv;
 	bool			blksz_datactrl16;
-- 
2.7.4