| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20181004213150.rdqhwpmtza3ez57p@Ettosoft-T55>
Date: Thu, 4 Oct 2018 23:31:52 +0200
From: ektor5 <ek5.chimenti@...il.com>
To: Hans Verkuil <hverkuil@...all.nl>
Cc: jacopo mondi <jacopo@...ndi.org>, luca.pisani@...o.org,
jose.abreu@...opsys.com, sean@...s.org,
sakari.ailus@...ux.intel.com,
Mauro Carvalho Chehab <mchehab@...nel.org>,
"David S. Miller" <davem@...emloft.net>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Andrew Morton <akpm@...ux-foundation.org>,
Arnd Bergmann <arnd@...db.de>,
Hans Verkuil <hans.verkuil@...co.com>,
Laurent Pinchart <laurent.pinchart@...asonboard.com>,
Geert Uytterhoeven <geert@...ux-m68k.org>,
Jacob Chen <jacob-chen@...wrt.com>,
Jacopo Mondi <jacopo+renesas@...ndi.org>,
Neil Armstrong <narmstrong@...libre.com>,
Todor Tomov <todor.tomov@...aro.org>,
linux-kernel@...r.kernel.org, linux-media@...r.kernel.org
Subject: Re: [PATCH 1/2] media: add SECO cec driver
Hi Hans,
On Thu, Oct 04, 2018 at 01:52:54PM +0200, Hans Verkuil wrote:
> On 10/03/18 11:35, jacopo mondi wrote:
> > Hi Ettore,
> > thanks for the patch.
> >
> > A few comments below, please have a look...
> >
> > On Tue, Oct 02, 2018 at 06:59:55PM +0200, ektor5 wrote:
> >> From: Ettore Chimenti <ek5.chimenti@...il.com>
> >>
> >> This patch adds support to the CEC device implemented with a STM32
> >> microcontroller in X86 SECO Boards, including UDOO X86.
> >>
> >> The communication is achieved via Braswell integrated SMBus
> >> (i2c-i801). The driver use direct access to the PCI addresses, due to
> >> the limitations of the specific driver in presence of ACPI calls.
> >>
> >> The basic functionalities are tested with success with cec-ctl and
> >> cec-compliance.
> >>
> >> Inspired by cros-ec-cec implementation, attaches to i915 driver
> >> cec-notifier.
> >>
> >> Signed-off-by: Ettore Chimenti <ek5.chimenti@...il.com>
> >> ---
> >> MAINTAINERS | 6 +
> >> drivers/media/platform/Kconfig | 11 +
> >> drivers/media/platform/Makefile | 4 +
> >> drivers/media/platform/seco-cec/Makefile | 1 +
> >> drivers/media/platform/seco-cec/seco-cec.c | 729 +++++++++++++++++++++
> >> drivers/media/platform/seco-cec/seco-cec.h | 132 ++++
> >> 6 files changed, 883 insertions(+)
> >> create mode 100644 drivers/media/platform/seco-cec/Makefile
> >> create mode 100644 drivers/media/platform/seco-cec/seco-cec.c
> >> create mode 100644 drivers/media/platform/seco-cec/seco-cec.h
> >>
> >> diff --git a/MAINTAINERS b/MAINTAINERS
> >> index 4ece30f15777..1062912a5ff4 100644
> >> --- a/MAINTAINERS
> >> +++ b/MAINTAINERS
> >> @@ -12972,6 +12972,12 @@ L: sdricohcs-devel@...ts.sourceforge.net (subscribers-only)
> >> S: Maintained
> >> F: drivers/mmc/host/sdricoh_cs.c
> >>
> >> +SECO BOARDS CEC DRIVER
> >> +M: Ettore Chimenti <ek5.chimenti@...il.com>
> >> +S: Maintained
> >> +F: drivers/media/platform/seco-cec/seco-cec.c
> >> +F: drivers/media/platform/seco-cec/seco-cec.h
> >> +
> >> SECURE COMPUTING
> >> M: Kees Cook <keescook@...omium.org>
> >> R: Andy Lutomirski <luto@...capital.net>
> >> diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
> >> index 94c1fe0e9787..f477764b902a 100644
> >> --- a/drivers/media/platform/Kconfig
> >> +++ b/drivers/media/platform/Kconfig
> >> @@ -613,6 +613,17 @@ config VIDEO_TEGRA_HDMI_CEC
> >> The CEC bus is present in the HDMI connector and enables communication
> >> between compatible devices.
> >>
> >> +config VIDEO_SECO_CEC
> >> + tristate "SECO Boards HDMI CEC driver"
> >> + depends on (X86 || IA64) || COMPILE_TEST
> >> + select CEC_CORE
> >> + select CEC_NOTIFIER
> >> + help
> >> + This is a driver for SECO Boards integrated CEC interface. It uses the
> >> + generic CEC framework interface.
> >
> > Is it worth mentioning the software framework used for implementing the driver?
> > Anyway, I see this is common to most of the CEC drivers here, so I
> > guess it is fine
>
> It's not worth mentioning :-)
>
> Not sure how and why that phrase crept into cec driver Kconfigs.
Ok, will remove that and add some more useful information. :)
>
> >
> >> + CEC bus is present in the HDMI connector and enables communication
> >> + between compatible devices.
> >> +
> >> endif #CEC_PLATFORM_DRIVERS
> >>
> >> menuconfig SDR_PLATFORM_DRIVERS
> >> diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
> >> index 41322ab65802..cc7365c787ba 100644
> >> --- a/drivers/media/platform/Makefile
> >> +++ b/drivers/media/platform/Makefile
> >> @@ -53,6 +53,10 @@ obj-$(CONFIG_VIDEO_TEGRA_HDMI_CEC) += tegra-cec/
> >>
> >> obj-y += stm32/
> >>
> >> +obj-$(CONFIG_VIDEO_SECO_CEC) += seco-cec/
> >> +
> >> +obj-y += blackfin/
> >> +
> >
> > Ups! Is this a leftover from some BSP code? It breaks the build on
> > media-tree master (and I guess on master too)
> >
> >> obj-y += davinci/
> >>
> >> obj-$(CONFIG_VIDEO_SH_VOU) += sh_vou.o
> >> diff --git a/drivers/media/platform/seco-cec/Makefile b/drivers/media/platform/seco-cec/Makefile
> >> new file mode 100644
> >> index 000000000000..a3f2c6bd3ac0
> >> --- /dev/null
> >> +++ b/drivers/media/platform/seco-cec/Makefile
> >> @@ -0,0 +1 @@
> >> +obj-$(CONFIG_VIDEO_SECO_CEC) += seco-cec.o
> >
> > This can simply be obj-y as you parse this makefile entry
> > conditionally to the presence of the CONFIG_VIDEO_SECO_CEC symbol
> >
> >> diff --git a/drivers/media/platform/seco-cec/seco-cec.c b/drivers/media/platform/seco-cec/seco-cec.c
> >> new file mode 100644
> >> index 000000000000..ba3b7c144a87
> >> --- /dev/null
> >> +++ b/drivers/media/platform/seco-cec/seco-cec.c
> >> @@ -0,0 +1,729 @@
> >> +// SPDX-License-Identifier: GPL-2.0 AND BSD-3-Clause
> >
> > Just make sure the AND is what you want (I only see OR clauses in
> > drivers/ code). See Documentation/process/license-rules.rst
> >
> >> +/*
> >> + *
> > Nit: empty comment line
> >> + * CEC driver for SECO X86 Boards
> >> + *
> >> + * Author: Ettore Chimenti <ek5.chimenti@...il.com>
> >> + * Copyright (C) 2018, SECO Srl.
> >> + * Copyright (C) 2018, Aidilab Srl.
> >> + *
> > Nit: empty comment line
> >> + */
> >> +
> >> +#include <linux/interrupt.h>
> >> +#include <linux/gpio.h>
> >> +#include <linux/gpio/consumer.h>
> >> +#include <linux/acpi.h>
> >> +#include <linux/platform_device.h>
> >> +#include <linux/delay.h>
> >> +#include <linux/pci.h>
> >> +#include <linux/dmi.h>
> >> +
> >> +/* CEC Framework */
> >> +#include <media/cec.h>
> >> +
> >> +#include "seco-cec.h"
> >
> > I would question why a header file is needed as it is not included by
> > anything else
> >
> >> +
> >> +struct secocec_data {
> >> + struct device *dev;
> >> + struct platform_device *pdev;
> >> + struct cec_adapter *cec_adap;
> >> + struct cec_notifier *notifier;
> >> + int irq;
> >> +};
> >> +
> >> +#define smb_wr16(cmd, data) smb_word_op(CMD_WORD_DATA, SECOCEC_MICRO_ADDRESS, \
> >> + cmd, data, SMBUS_WRITE, NULL)
> >> +#define smb_rd16(cmd, res) smb_word_op(CMD_WORD_DATA, SECOCEC_MICRO_ADDRESS, \
> >> + cmd, 0, SMBUS_READ, res)
> >> +
> >> +static int smb_word_op(short data_format, u16 slave_addr, u8 cmd, u16 data,
> >> + u8 operation, u16 *result)
> >> +{
> >> + unsigned int count;
> >> + short _data_format;
> >> + int ret, status = 0;
> >
> > In the rest of the function ret is used only once, and you can use
> > status in its place. Please drop one of the two.
> >
> >> +
> >> + switch (data_format) {
> >> + case CMD_BYTE_DATA:
> >> + _data_format = BRA_SMB_CMD_BYTE_DATA;
> >> + break;
> >> + case CMD_WORD_DATA:
> >> + _data_format = BRA_SMB_CMD_WORD_DATA;
> >> + break;
> >> + default:
> >> + return -EINVAL;
> >> + }
> >> +
> >> + /* Active wait until ready */
> >> + for (count = 0; count <= SMBTIMEOUT; ++count) {
> >> + if (!(inb(HSTS) & BRA_INUSE_STS))
> >> + break;
> >> + udelay(SMB_POLL_UDELAY);
> >> + }
> >> +
> >> + if (count > SMBTIMEOUT) {
> >> + /* Reset the lock instead of failing */
> >> + outb(0xff, HSTS);
> >> + pr_warn("%s: SMBTIMEOUT\n", __func__);
> >
> > No pr_debug/pr_warn if possible, please.
> >
> >> + }
> >> +
> >> + outb(0x00, HCNT);
> >> + outb((u8)(slave_addr & 0xfe) | operation, XMIT_SLVA);
> >> + outb(cmd, HCMD);
> >> + inb(HCNT);
> >> +
> >> + if (operation == SMBUS_WRITE) {
> >> + outb((u8)data, HDAT0);
> >> + outb((u8)(data >> 8), HDAT1);
> >> + pr_debug("%s: WRITE (0x%02x - count %05d): 0x%04x\n",
> >> + __func__, cmd, count, data);
> >> + }
> >> +
> >> + outb(BRA_START + _data_format, HCNT);
> >> +
> >> + for (count = 0; count <= SMBTIMEOUT; count++) {
> >> + if (!(inb(HSTS) & BRA_HOST_BUSY))
> >> + break;
> >> + udelay(SMB_POLL_UDELAY);
> >> + }
> >> +
> >> + if (count > SMBTIMEOUT) {
> >> + pr_debug("%s: SMBTIMEOUT_1\n", __func__);
> >> + status = -EBUSY;
> >> + goto err;
> >> + }
> >> +
> >> + ret = inb(HSTS);
> >> + if (ret & BRA_HSTS_ERR_MASK) {
> >> + pr_debug("%s: HSTS(0x%02X): 0x%X\n", __func__, cmd, ret);
> >> + status = -EIO;
> >> + goto err;
> >> + }
> >> +
> >> + if (operation == SMBUS_READ) {
> >> + *result = ((inb(HDAT0) & 0xff) + ((inb(HDAT1) & 0xff) << 8));
> >> + pr_debug("%s: READ (0x%02x - count %05d): 0x%04x\n",
> >> + __func__, cmd, count, *result);
> >> + }
> >> +
> >> +err:
> >> + outb(0xff, HSTS);
> >> + return status;
> >> +}
> >> +
> >> +static int secocec_adap_enable(struct cec_adapter *adap, bool enable)
> >> +{
> >> + struct secocec_data *cec = cec_get_drvdata(adap);
> >> + struct device *dev = cec->dev;
> >> + u16 val = 0;
> >> + int status;
> >> +
> >> + if (enable) {
> >> + /* Clear the status register */
> >> + status = smb_rd16(SECOCEC_STATUS_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* Enable the interrupts */
> >> + status = smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1,
> >> + val | SECOCEC_ENABLE_REG_1_CEC);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "Device enabled");
> >> +
> >
> > Empty line
> >
> >> + } else {
> >> + /* Clear the status register */
> >> + status = smb_rd16(SECOCEC_STATUS_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* Disable the interrupts */
> >> + status = smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1, val &
> >> + ~SECOCEC_ENABLE_REG_1_CEC &
> >> + ~SECOCEC_ENABLE_REG_1_IR);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "Device disabled");
> >> + }
> >> +
> >> + return 0;
> >> +err:
> >> + dev_err(dev, "Adapter setup failed (%d)", status);
> >> + return status;
> >> +}
> >> +
> >> +static int secocec_adap_log_addr(struct cec_adapter *adap, u8 logical_addr)
> >> +{
> >> + u16 enable_val = 0;
> >> + int status;
> >> +
> >> + /* Disable device */
> >> + status = smb_rd16(SECOCEC_ENABLE_REG_1, &enable_val);
> >> + if (status)
> >> + return status;
> >> +
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1,
> >> + enable_val & ~SECOCEC_ENABLE_REG_1_CEC);
> >> + if (status)
> >> + return status;
> >> +
> >> + /* Write logical address */
> >> + status = smb_wr16(SECOCEC_DEVICE_LA, logical_addr);
> >> + if (status)
> >> + return status;
> >> +
> >> + /* Re-enable device */
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1,
> >> + enable_val | SECOCEC_ENABLE_REG_1_CEC);
> >> + if (status)
> >> + return status;
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int secocec_adap_transmit(struct cec_adapter *adap, u8 attempts,
> >> + u32 signal_free_time, struct cec_msg *msg)
> >> +{
> >> + struct secocec_data *cec = cec_get_drvdata(adap);
> >> + struct device *dev = cec->dev;
> >> + u16 payload_len, payload_id_len, destination, val = 0;
> >> + u8 *payload_msg;
> >> + int status;
> >> + u8 i;
> >> +
> >> + /* Device msg len already accounts for header */
> >> + payload_id_len = msg->len - 1;
> >> +
> >> + /* Send data length */
> >> + status = smb_wr16(SECOCEC_WRITE_DATA_LENGTH, payload_id_len);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* Send Operation ID if present */
> >> + if (payload_id_len > 0) {
> >> + status = smb_wr16(SECOCEC_WRITE_OPERATION_ID, msg->msg[1]);
> >> + if (status)
> >> + goto err;
> >> + }
> >> + /* Send data if present */
> >> + if (payload_id_len > 1) {
> >> + /* Only data; */
> >> + payload_len = msg->len - 2;
> >> + payload_msg = &msg->msg[2];
> >> +
> >> + /* Copy message into registers */
> >> + for (i = 0; i < payload_len / 2 + payload_len % 2; i++) {
> >> + /* hi byte */
> >> + val = payload_msg[(i << 1) + 1] << 8;
> >> +
> >> + /* lo byte */
> >> + val |= payload_msg[(i << 1)];
> >> +
> >> + status = smb_wr16(SECOCEC_WRITE_DATA_00 + i, val);
> >> + if (status)
> >> + goto err;
> >> + }
> >> + }
> >> + /* Send msg source/destination and fire msg */
> >> + destination = msg->msg[0];
> >> + status = smb_wr16(SECOCEC_WRITE_BYTE0, destination);
> >> + if (status)
> >> + goto err;
> >> +
> >> + return 0;
> >> +
> >> +err:
> >> + dev_err(dev, "Transmit failed (%d)", status);
> >> + return status;
> >> +}
> >> +
> >> +static int secocec_tx_done(struct cec_adapter *adap, u16 status_val)
> >> +{
> >> + int status = 0;
> >> +
> >> + if (status_val & SECOCEC_STATUS_TX_ERROR_MASK) {
> >> + if (status_val & SECOCEC_STATUS_TX_NACK_ERROR) {
> >> + cec_transmit_attempt_done(adap, CEC_TX_STATUS_NACK);
> >> + status = -EAGAIN;
> >> + } else {
> >> + cec_transmit_attempt_done(adap, CEC_TX_STATUS_ERROR);
> >> + status = -EIO;
> >> + }
> >> + } else {
> >> + cec_transmit_attempt_done(adap, CEC_TX_STATUS_OK);
> >> + }
> >> +
> >> + /* Reset status reg */
> >> + status_val = SECOCEC_STATUS_TX_ERROR_MASK |
> >> + SECOCEC_STATUS_MSG_SENT_MASK |
> >> + SECOCEC_STATUS_TX_NACK_ERROR;
> >> + smb_wr16(SECOCEC_STATUS, status_val);
> >> +
> >> + return status;
> >> +}
> >> +
> >> +static int secocec_rx_done(struct cec_adapter *adap, u16 status_val)
> >> +{
> >> + struct secocec_data *cec = cec_get_drvdata(adap);
> >> + struct device *dev = cec->dev;
> >> + struct cec_msg msg = { };
> >> + bool flag_overflow = false;
> >> + u8 payload_len, i = 0;
> >> + u8 *payload_msg;
> >> + u16 val = 0;
> >> + int status;
> >> +
> >> + if (status_val & SECOCEC_STATUS_RX_OVERFLOW_MASK) {
> >> + dev_warn(dev, "Received more than 16 bytes. Discarding");
> >> + flag_overflow = true;
> >> + }
> >> +
> >> + if (status_val & SECOCEC_STATUS_RX_ERROR_MASK) {
> >> + dev_warn(dev, "Message received with errors. Discarding");
> >> + status = -EIO;
> >> + goto rxerr;
> >> + }
> >> +
> >> + /* Read message length */
> >> + status = smb_rd16(SECOCEC_READ_DATA_LENGTH, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "Incoming message (payload len %d):", val);
> >> +
> >> + /* Device msg len already accounts for the header */
> >> + msg.len = min(val + 1, CEC_MAX_MSG_SIZE);
> >> +
> >> + /* Read logical address */
> >> + status = smb_rd16(SECOCEC_READ_BYTE0, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* device stores source LA and destination */
> >> + msg.msg[0] = val;
> >> +
> >> + /* Read operation ID if present */
> >> + if (msg.len > 0) {
> >
> > Am I wrong or msg.len is at least (val + 1) and val is never negative?
> > If that's true, this condition is always verified.
> >
> >> + status = smb_rd16(SECOCEC_READ_OPERATION_ID, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + msg.msg[1] = val;
> >> + }
> >> +
> >> + /* Read data if present */
> >> + if (msg.len > 1) {
> >> + payload_len = msg.len - 2;
> >> + payload_msg = &msg.msg[2];
> >> +
> >> + /* device stores 2 bytes in every 16-bit val */
> >> + for (i = 0; i < payload_len / 2 + payload_len % 2; i++) {
> >> + status = smb_rd16(SECOCEC_READ_DATA_00 + i, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* low byte, skipping header */
> >> + payload_msg[(i << 1)] = val & 0x00ff;
> >> +
> >> + /* hi byte */
> >> + payload_msg[(i << 1) + 1] = (val & 0xff00) >> 8;
> >> + }
> >> + }
> >> +
> >> + cec_received_msg(cec->cec_adap, &msg);
> >> +
> >> + /* Reset status reg */
> >> + status_val = SECOCEC_STATUS_MSG_RECEIVED_MASK;
> >> + if (flag_overflow)
> >> + status_val |= SECOCEC_STATUS_RX_OVERFLOW_MASK;
> >> +
> >> + status = smb_wr16(SECOCEC_STATUS, status_val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "Message received successfully");
> >> +
> >> + return 0;
> >> +
> >> +rxerr:
> >> + /* Reset error reg */
> >> + status_val = SECOCEC_STATUS_MSG_RECEIVED_MASK |
> >> + SECOCEC_STATUS_RX_ERROR_MASK;
> >> + if (flag_overflow)
> >> + status_val |= SECOCEC_STATUS_RX_OVERFLOW_MASK;
> >> + smb_wr16(SECOCEC_STATUS, status_val);
> >> +
> >> +err:
> >> + dev_err(dev, "Receive message failed (%d)", status);
> >> + return status;
> >> +}
> >> +
> >> +struct cec_adap_ops secocec_cec_adap_ops = {
> >> + /* Low-level callbacks */
> >> + .adap_enable = secocec_adap_enable,
> >> + .adap_log_addr = secocec_adap_log_addr,
> >> + .adap_transmit = secocec_adap_transmit,
> >> +};
> >> +
> >> +static irqreturn_t secocec_irq_handler(int irq, void *priv)
> >> +{
> >> + struct secocec_data *cec = priv;
> >> + struct device *dev = cec->dev;
> >> + u16 status_val, cec_val, val = 0;
> >> + int status;
> >> +
> >> + /* Read status register */
> >> + status = smb_rd16(SECOCEC_STATUS_REG_1, &status_val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + if (status_val & SECOCEC_STATUS_REG_1_CEC) {
> >> + dev_dbg(dev, "+++++ CEC Interrupt Caught");
> >
> > Just be carefull in too much printouts while handling interrupts.
> > Also, I would not insert custom printout formats (here and below in
> > this functions). I would simply drop this one.
> >
> >> +
> >> + /* Read CEC status register */
> >> + status = smb_rd16(SECOCEC_STATUS, &cec_val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + if (cec_val & SECOCEC_STATUS_MSG_RECEIVED_MASK)
> >> + secocec_rx_done(cec->cec_adap, cec_val);
> >> +
> >> + if (cec_val & SECOCEC_STATUS_MSG_SENT_MASK)
> >> + secocec_tx_done(cec->cec_adap, cec_val);
> >> +
> >> + if ((~cec_val & SECOCEC_STATUS_MSG_SENT_MASK) &&
> >> + (~cec_val & SECOCEC_STATUS_MSG_RECEIVED_MASK))
> >> + dev_warn(dev,
> >> + "Message not received or sent, but interrupt fired \\_\"._/");
> >
> > No custom funny printouts please :)
> >
> >> +
> >> + val = SECOCEC_STATUS_REG_1_CEC;
> >> + }
> >> +
> >> + if (status_val & SECOCEC_STATUS_REG_1_IR) {
> >> + dev_dbg(dev, "IR RC5 Interrupt Caught");
> >
> > How frequent is this one? Do you need to print it out?
> >
> >> + val |= SECOCEC_STATUS_REG_1_IR;
> >> + /* TODO IRDA RX */
> >> + }
> >> +
> >> + /* Reset status register */
> >> + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "----- CEC Interrupt Handled");
> >
> > Drop this one please
> >
> >> +
> >> + return IRQ_HANDLED;
> >> +
> >> +err:
> >> + dev_err(dev, "IRQ: Read/Write SMBus operation failed (%d)", status);
> >> +
> >> + /* Reset status register */
> >> + val = SECOCEC_STATUS_REG_1_CEC | SECOCEC_STATUS_REG_1_IR;
> >> + smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> +
> >> + return IRQ_HANDLED;
> >> +}
> >> +
> >> +struct cec_dmi_match {
> >> + char *sys_vendor;
> >> + char *product_name;
> >> + char *devname;
> >> + char *conn;
> >> +};
> >> +
> >> +static const struct cec_dmi_match secocec_dmi_match_table[] = {
> >> + /* UDOO X86 */
> >> + { "SECO", "UDOO x86", "0000:00:02.0", "Port B" },
> >> +};
> >> +
> >> +static int secocec_cec_get_notifier(struct cec_notifier **notify)
>
> If you compare this driver with cros-ec-cec.c, then you'll see that
> there this function is under "#if IS_ENABLED(CONFIG_PCI) && IS_ENABLED(CONFIG_DMI)".
>
> I think you should do the same and (just like cros-ec-cec.c) add a dummy function
> in the #else part.
I'm not sure about this. Doing so, compiling without CONFIG_PCI or
CONFIG_DMI, it will fail later when no notifier is found (now it will
probably fail at compile time). Should I select them in the Kconfig or
it is better to eventually disable the notifier and go on adding
CEC_CAP_PHYS_ADDR to device capabilities?
>
> >> +{
> >> + int i;
> >> +
> >> + for (i = 0 ; i < ARRAY_SIZE(secocec_dmi_match_table) ; ++i) {
> >> + const struct cec_dmi_match *m = &secocec_dmi_match_table[i];
> >> +
> >> + if (dmi_match(DMI_SYS_VENDOR, m->sys_vendor) &&
> >> + dmi_match(DMI_PRODUCT_NAME, m->product_name)) {
> >> + struct device *d;
> >> +
> >> + /* Find the device, bail out if not yet registered */
> >> + d = bus_find_device_by_name(&pci_bus_type, NULL,
> >> + m->devname);
> >> + if (!d)
> >> + return -EPROBE_DEFER;
> >> +
> >> + *notify = cec_notifier_get_conn(d, m->conn);
> >
> > Nit: it's usually nice to have an empty line before return (here and in
> > other places). Not mandatory though.
> >
> >> + return 0;
> >> + }
> >> + }
> >> +
> >> + return -EINVAL;
> >> +}
> >> +
> >> +static int secocec_acpi_probe(struct secocec_data *sdev)
> >> +{
> >> + struct device *dev = sdev->dev;
> >> + struct gpio_desc *gpio;
> >> + int irq = 0;
> >> +
> >> + gpio = devm_gpiod_get(dev, NULL, GPIOF_IN);
> >> + if (IS_ERR(gpio)) {
> >> + dev_err(dev, "Cannot request interrupt gpio");
> >> + return PTR_ERR(gpio);
> >> + }
> >> +
> >> + irq = gpiod_to_irq(gpio);
> >> + if (irq < 0) {
> >> + dev_err(dev, "Cannot find valid irq");
> >> + return -ENODEV;
> >> + }
> >> + dev_dbg(dev, "irq-gpio is bound to IRQ %d", irq);
> >> +
> >> + sdev->irq = irq;
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int secocec_probe(struct platform_device *pdev)
> >> +{
> >> + struct secocec_data *secocec;
> >> + struct device *dev = &pdev->dev;
> >> + u8 cec_caps;
> >> + int ret;
> >> + u16 val;
> >> +
> >> + secocec = devm_kzalloc(dev, sizeof(*secocec), GFP_KERNEL);
> >> + if (!secocec)
> >> + return -ENOMEM;
> >> +
> >> + dev_set_drvdata(dev, secocec);
> >> +
> >> + /* Request SMBus regions */
> >> + if (!request_muxed_region(BRA_SMB_BASE_ADDR, 7, "CEC00001")) {
> >> + dev_err(dev, "Request memory region failed");
> >> + return -ENXIO;
> >> + }
> >> +
> >> + secocec->pdev = pdev;
> >> + secocec->dev = dev;
> >> +
> >> + if (!has_acpi_companion(dev)) {
> >> + dev_dbg(dev, "Cannot find any ACPI companion");
> >> + ret = -ENODEV;
> >> + goto err;
> >> + }
> >> +
> >> + ret = secocec_acpi_probe(secocec);
> >> + if (ret) {
> >> + dev_err(dev, "Cannot assign gpio to IRQ");
> >> + ret = -ENODEV;
> >> + goto err;
> >> + }
> >> +
> >> + dev_dbg(dev, "IRQ detected at %d", secocec->irq);
> >> +
> >> + /* Firmware version check */
> >> + ret = smb_rd16(SECOCEC_VERSION, &val);
> >> + if (ret) {
> >> + dev_err(dev, "Cannot check fw version");
> >> + goto err;
> >> + }
> >> + if (val < SECOCEC_LATEST_FW) {
> >> + dev_err(dev, "CEC Firmware not supported (v.%04x). Use ver > v.%04x",
> >> + val, SECOCEC_LATEST_FW);
> >> + ret = -EINVAL;
> >> + goto err;
> >> + }
> >> +
> >> +#ifdef CONFIG_CEC_NOTIFIER
> >
> > Your Kconfig entry selects CEC_NOTIFIER.
>
> Yes, this #ifdef line can be dropped.
Yes, agree.
>
> >
> > (I won't comment on the cec_notifier handling part, as I don't know
> > much. I just see other drivers registering and getting the notifier
> > using the cec_notifier_ functions, while it seems to me you don't.
> > Maybe it's fine...)
>
> It's fine :-)
>
> >
> >> + ret = secocec_cec_get_notifier(&secocec->notifier);
> >> + if (ret) {
> >> + dev_err(dev, "no CEC notifier available\n");
> >> + goto err;
> >> + }
> >> +#endif
> >> +
> >> + ret = devm_request_threaded_irq(dev,
> >> + secocec->irq,
> >> + NULL,
> >> + secocec_irq_handler,
> >> + IRQF_TRIGGER_RISING | IRQF_ONESHOT,
> >> + dev_name(&pdev->dev), secocec);
> >> +
> >> + if (ret) {
> >> + dev_err(dev, "Cannot request IRQ %d", secocec->irq);
> >> + ret = -EIO;
> >> + goto err;
> >> + }
> >> +
> >> + /* Allocate CEC adapter */
> >> + cec_caps = CEC_CAP_DEFAULTS;
> >> +
> >> + secocec->cec_adap = cec_allocate_adapter(&secocec_cec_adap_ops,
> >> + secocec,
> >> + dev_name(dev),
> >> + cec_caps, SECOCEC_MAX_ADDRS);
>
> You can drop cec_caps and just pass CEC_CAP_DEFAULTS directly.
>
> >> +
> >> + if (IS_ERR(secocec->cec_adap)) {
> >> + ret = PTR_ERR(secocec->cec_adap);
> >> + goto err;
> >> + }
> >> +
> >> + ret = cec_register_adapter(secocec->cec_adap, dev);
> >> + if (ret)
> >> + goto err_delete_adapter;
> >> +
> >> + if (secocec->notifier)
> >> + cec_register_cec_notifier(secocec->cec_adap, secocec->notifier);
> >> +
> >> + platform_set_drvdata(pdev, secocec);
> >> +
> >> + dev_dbg(dev, "Device registered");
> >> +
> >> + return ret;
> >> +
> >> +err_delete_adapter:
> >> + cec_delete_adapter(secocec->cec_adap);
> >> +err:
> >> + dev_err(dev, "%s device probe failed\n", dev_name(dev));
> >> +
> >> + return ret;
> >> +}
> >> +
> >> +/* ----------------------------------------------------------------------- */
> >> +
> >> +static int secocec_remove(struct platform_device *pdev)
> >> +{
> >> + struct secocec_data *secocec = platform_get_drvdata(pdev);
> >> +
> >> + cec_unregister_adapter(secocec->cec_adap);
> >> +
> >> + if (secocec->notifier)
> >> + cec_notifier_put(secocec->notifier);
> >> +
> >> + release_region(BRA_SMB_BASE_ADDR, 7);
> >> +
> >> + dev_dbg(&pdev->dev, "CEC device removed");
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +/* ----------------------------------------------------------------------- */
> >> +
> >> +#ifdef CONFIG_PM_SLEEP
> >
> > I see CONFIG_PM_SLEEP is only selected if support for
> > 'suspend'/'hibernate' is enabled. Is this what you want, or you should
> > check for CONFIG_PM?
> >
> >> +static int secocec_suspend(struct device *dev)
> >> +{
> >> + u16 val;
> >> + int status;
> >> +
> >> + dev_dbg(dev, "Device going to suspend, disabling");
> >> +
> >> + /* Clear the status register */
> >> + status = smb_rd16(SECOCEC_STATUS_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* Disable the interrupts */
> >> + status = smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1, val &
> >> + ~SECOCEC_ENABLE_REG_1_CEC & ~SECOCEC_ENABLE_REG_1_IR);
> >> + if (status)
> >> + goto err;
> >> +
> >> + return 0;
> >> +
> >> +err:
> >> + dev_err(dev, "Suspend failed (err: %d)", status);
> >> + return status;
> >> +}
> >> +
> >> +static int secocec_resume(struct device *dev)
> >> +{
> >> + u16 val;
> >> + int status;
> >> +
> >> + dev_dbg(dev, "Resuming device from suspend");
> >> +
> >> + /* Clear the status register */
> >> + status = smb_rd16(SECOCEC_STATUS_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + /* Enable the interrupts */
> >> + status = smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> >> + if (status)
> >> + goto err;
> >> +
> >> + status = smb_wr16(SECOCEC_ENABLE_REG_1, val | SECOCEC_ENABLE_REG_1_CEC);
> >> + if (status)
> >> + goto err;
> >> +
> >> + dev_dbg(dev, "Device resumed from suspend");
> >> +
> >> + return 0;
> >> +
> >> +err:
> >> + dev_err(dev, "Resume failed (err: %d)", status);
> >> + return status;
> >> +}
> >> +
> >> +static SIMPLE_DEV_PM_OPS(secocec_pm_ops, secocec_suspend, secocec_resume);
> >> +#define SECOCEC_PM_OPS (&secocec_pm_ops)
> >> +#else
> >> +#define SECOCEC_PM_OPS NULL
> >> +#endif
> >> +
> >> +#ifdef CONFIG_ACPI
> >> +static const struct acpi_device_id secocec_acpi_match[] = {
> >> + {"CEC00001", 0},
> >> + {},
> >> +};
> >> +
> >> +MODULE_DEVICE_TABLE(acpi, secocec_acpi_match);
> >> +#endif
> >> +
> >> +static struct platform_driver secocec_driver = {
> >> + .driver = {
> >> + .name = SECOCEC_DEV_NAME,
> >> + .acpi_match_table = ACPI_PTR(secocec_acpi_match),
> >> + .pm = SECOCEC_PM_OPS,
> >> + },
> >> + .probe = secocec_probe,
> >> + .remove = secocec_remove,
> >> +};
> >
> > As you can see most of my comments are nits or trivial things. I would
> > wait for more feedbacks on the CEC and x86/SMbus part from others before
> > sending v2 if I were you :)
> >
> > Thanks
> > j
> >
> >
> >> +
> >> +module_platform_driver(secocec_driver);
> >> +
> >> +MODULE_DESCRIPTION("SECO CEC X86 Driver");
> >> +MODULE_AUTHOR("Ettore Chimenti <ek5.chimenti@...il.com>");
> >> +MODULE_LICENSE("Dual BSD/GPL");
> >> diff --git a/drivers/media/platform/seco-cec/seco-cec.h b/drivers/media/platform/seco-cec/seco-cec.h
> >> new file mode 100644
> >> index 000000000000..cc7f0cba8e9e
> >> --- /dev/null
> >> +++ b/drivers/media/platform/seco-cec/seco-cec.h
> >> @@ -0,0 +1,132 @@
> >> +/* SPDX-License-Identifier: GPL-2.0 AND BSD-3-Clause */
> >> +/*
> >> + *
> >> + * SECO X86 Boards CEC register defines
> >> + *
> >> + * Author: Ettore Chimenti <ek5.chimenti@...il.com>
> >> + * Copyright (C) 2018, SECO Srl.
> >> + * Copyright (C) 2018, Aidilab Srl.
> >> + *
> >> + */
> >> +
> >> +#ifndef __SECO_CEC_H__
> >> +#define __SECO_CEC_H__
> >> +
> >> +#define SECOCEC_MAX_ADDRS 1
> >> +#define SECOCEC_DEV_NAME "secocec"
> >> +#define SECOCEC_LATEST_FW 0x0f0b
> >> +
> >> +#define SMBTIMEOUT 0xffff
> >> +#define SMB_POLL_UDELAY 10
> >> +
> >> +#define SMBUS_WRITE 0
> >> +#define SMBUS_READ 1
> >> +
> >> +#define CMD_BYTE_DATA 0
> >> +#define CMD_WORD_DATA 1
> >> +
> >> +/*
> >> + * SMBus definitons for Braswell
> >> + */
> >> +
> >> +#define BRA_DONE_STATUS BIT(7)
> >> +#define BRA_INUSE_STS BIT(6)
> >> +#define BRA_FAILED_OP BIT(4)
> >> +#define BRA_BUS_ERR BIT(3)
> >> +#define BRA_DEV_ERR BIT(2)
> >> +#define BRA_INTR BIT(1)
> >> +#define BRA_HOST_BUSY BIT(0)
> >> +#define BRA_HSTS_ERR_MASK (BRA_FAILED_OP | BRA_BUS_ERR | BRA_DEV_ERR)
> >> +
> >> +#define BRA_PEC_EN BIT(7)
> >> +#define BRA_START BIT(6)
> >> +#define BRA_LAST__BYTE BIT(5)
> >> +#define BRA_INTREN BIT(0)
> >> +#define BRA_SMB_CMD (7 << 2)
> >> +#define BRA_SMB_CMD_QUICK (0 << 2)
> >> +#define BRA_SMB_CMD_BYTE (1 << 2)
> >> +#define BRA_SMB_CMD_BYTE_DATA (2 << 2)
> >> +#define BRA_SMB_CMD_WORD_DATA (3 << 2)
> >> +#define BRA_SMB_CMD_PROCESS_CALL (4 << 2)
> >> +#define BRA_SMB_CMD_BLOCK (5 << 2)
> >> +#define BRA_SMB_CMD_I2CREAD (6 << 2)
> >> +#define BRA_SMB_CMD_BLOCK_PROCESS (7 << 2)
> >> +
> >> +#define BRA_SMB_BASE_ADDR 0x2040
> >> +#define HSTS (BRA_SMB_BASE_ADDR + 0)
> >> +#define HCNT (BRA_SMB_BASE_ADDR + 2)
> >> +#define HCMD (BRA_SMB_BASE_ADDR + 3)
> >> +#define XMIT_SLVA (BRA_SMB_BASE_ADDR + 4)
> >> +#define HDAT0 (BRA_SMB_BASE_ADDR + 5)
> >> +#define HDAT1 (BRA_SMB_BASE_ADDR + 6)
> >> +
> >> +/*
> >> + * Microcontroller Address
> >> + */
> >> +
> >> +#define SECOCEC_MICRO_ADDRESS 0x40
> >> +
> >> +/*
> >> + * STM32 SMBus Registers
> >> + */
> >> +
> >> +#define SECOCEC_VERSION 0x00
> >> +#define SECOCEC_ENABLE_REG_1 0x01
> >> +#define SECOCEC_ENABLE_REG_2 0x02
> >> +#define SECOCEC_STATUS_REG_1 0x03
> >> +#define SECOCEC_STATUS_REG_2 0x04
> >> +
> >> +#define SECOCEC_STATUS 0x28
> >> +#define SECOCEC_DEVICE_LA 0x29
> >> +#define SECOCEC_READ_OPERATION_ID 0x2a
> >> +#define SECOCEC_READ_DATA_LENGTH 0x2b
> >> +#define SECOCEC_READ_DATA_00 0x2c
> >> +#define SECOCEC_READ_DATA_02 0x2d
> >> +#define SECOCEC_READ_DATA_04 0x2e
> >> +#define SECOCEC_READ_DATA_06 0x2f
> >> +#define SECOCEC_READ_DATA_08 0x30
> >> +#define SECOCEC_READ_DATA_10 0x31
> >> +#define SECOCEC_READ_DATA_12 0x32
> >> +#define SECOCEC_READ_BYTE0 0x33
> >> +#define SECOCEC_WRITE_OPERATION_ID 0x34
> >> +#define SECOCEC_WRITE_DATA_LENGTH 0x35
> >> +#define SECOCEC_WRITE_DATA_00 0x36
> >> +#define SECOCEC_WRITE_DATA_02 0x37
> >> +#define SECOCEC_WRITE_DATA_04 0x38
> >> +#define SECOCEC_WRITE_DATA_06 0x39
> >> +#define SECOCEC_WRITE_DATA_08 0x3a
> >> +#define SECOCEC_WRITE_DATA_10 0x3b
> >> +#define SECOCEC_WRITE_DATA_12 0x3c
> >> +#define SECOCEC_WRITE_BYTE0 0x3d
> >> +
> >> +#define SECOCEC_IR_READ_DATA 0x3e
> >> +
> >> +/*
> >> + * Enabling register
> >> + */
> >> +
> >> +#define SECOCEC_ENABLE_REG_1_CEC 0x1000
> >> +#define SECOCEC_ENABLE_REG_1_IR 0x2000
> >> +#define SECOCEC_ENABLE_REG_1_IR_PASSTHROUGH 0x4000
> >> +
> >> +/*
> >> + * Status register
> >> + */
> >> +
> >> +#define SECOCEC_STATUS_REG_1_CEC SECOCEC_ENABLE_REG_1_CEC
> >> +#define SECOCEC_STATUS_REG_1_IR SECOCEC_ENABLE_REG_1_IR
> >> +#define SECOCEC_STATUS_REG_1_IR_PASSTHR SECOCEC_ENABLE_REG_1_IR_PASSTHR
> >> +
> >> +/*
> >> + * Status data
> >> + */
> >> +
> >> +#define SECOCEC_STATUS_MSG_RECEIVED_MASK BIT(0)
> >> +#define SECOCEC_STATUS_RX_ERROR_MASK BIT(1)
> >> +#define SECOCEC_STATUS_MSG_SENT_MASK BIT(2)
> >> +#define SECOCEC_STATUS_TX_ERROR_MASK BIT(3)
> >> +
> >> +#define SECOCEC_STATUS_TX_NACK_ERROR BIT(4)
> >> +#define SECOCEC_STATUS_RX_OVERFLOW_MASK BIT(5)
> >> +
> >> +#endif /* __SECO_CEC_H__ */
> >> --
> >> 2.18.0
> >>
>
> Regards,
>
> Hans
Thanks a lot again,
Ettore
Powered by blists - more mailing lists