Message-ID: <20181006065726.GL12063@builder>
Date:   Fri, 5 Oct 2018 23:57:26 -0700
From:   Bjorn Andersson <bjorn.andersson@...aro.org>
To:     Rohit kumar <rohitkr@...eaurora.org>
Cc:     ohad@...ery.com, robh+dt@...nel.org, mark.rutland@....com,
        linux-remoteproc@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, plai@...eaurora.org,
        bgoswami@...eaurora.org, rohkumar@....qualcomm.com
Subject: Re: [PATCH v4] remoteproc: qcom: Introduce Non-PAS ADSP PIL driver

On Mon 24 Sep 04:07 PDT 2018, Rohit kumar wrote:

> This adds Non PAS ADSP PIL driver for Qualcomm
> Technologies Inc SoCs.
> Added initial support for SDM845 with ADSP bootup and
> shutdown operation handled from Application Processor
> SubSystem(APSS).
> 
> Signed-off-by: Rohit kumar <rohitkr@...eaurora.org>

Sorry for missing this on the last few patches, I thought we said we
where going to name the driver qcom_q6v5_adsp. Rather than spending more
time on this I applied the patch with this change, as it does look good.

Please let me know if you have any concerns with this.

Regards,
Bjorn

> ---
> Changes since v3:
> 	Addressed comments posted by Sibi
> 
> This patch is dependent on the rpmh powerdomain driver https://lkml.org/lkml/2018/6/27/7
> and renaming of Hexagon v5 PAS driver https://patchwork.kernel.org/patch/10601119/ .
> 
>  drivers/remoteproc/Kconfig         |  14 ++
>  drivers/remoteproc/Makefile        |   1 +
>  drivers/remoteproc/qcom_adsp_pil.c | 502 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 517 insertions(+)
>  create mode 100644 drivers/remoteproc/qcom_adsp_pil.c
> 
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index 8894935..f554669 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -140,6 +140,20 @@ config QCOM_Q6V5_WCSS
>  	  Say y here to support the Qualcomm Peripheral Image Loader for the
>  	  Hexagon V5 based WCSS remote processors.
>  
> +config QCOM_ADSP_PIL
> +	tristate "Qualcomm Technology Inc ADSP Peripheral Image Loader"
> +	depends on OF && ARCH_QCOM
> +	depends on QCOM_SMEM
> +	depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
> +	depends on QCOM_SYSMON || QCOM_SYSMON=n
> +	select MFD_SYSCON
> +	select QCOM_MDT_LOADER
> +	select QCOM_Q6V5_COMMON
> +	select QCOM_RPROC_COMMON
> +	help
> +	  Say y here to support the Peripheral Image Loader
> +	  for the Qualcomm Technology Inc. ADSP remote processors.
> +
>  config QCOM_SYSMON
>  	tristate "Qualcomm sysmon driver"
>  	depends on RPMSG
> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
> index 050f41a..0e1b89c 100644
> --- a/drivers/remoteproc/Makefile
> +++ b/drivers/remoteproc/Makefile
> @@ -19,6 +19,7 @@ obj-$(CONFIG_QCOM_Q6V5_COMMON)		+= qcom_q6v5.o
>  obj-$(CONFIG_QCOM_Q6V5_MSS)		+= qcom_q6v5_mss.o
>  obj-$(CONFIG_QCOM_Q6V5_PAS)		+= qcom_q6v5_pas.o
>  obj-$(CONFIG_QCOM_Q6V5_WCSS)		+= qcom_q6v5_wcss.o
> +obj-$(CONFIG_QCOM_ADSP_PIL)		+= qcom_adsp_pil.o
>  obj-$(CONFIG_QCOM_SYSMON)		+= qcom_sysmon.o
>  obj-$(CONFIG_QCOM_WCNSS_PIL)		+= qcom_wcnss_pil.o
>  qcom_wcnss_pil-y			+= qcom_wcnss.o
> diff --git a/drivers/remoteproc/qcom_adsp_pil.c b/drivers/remoteproc/qcom_adsp_pil.c
> new file mode 100644
> index 0000000..f2f5e56
> --- /dev/null
> +++ b/drivers/remoteproc/qcom_adsp_pil.c
> @@ -0,0 +1,502 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Qualcomm Technology Inc. ADSP Peripheral Image Loader for SDM845.
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/firmware.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_domain.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regmap.h>
> +#include <linux/remoteproc.h>
> +#include <linux/reset.h>
> +#include <linux/soc/qcom/mdt_loader.h>
> +#include <linux/soc/qcom/smem.h>
> +#include <linux/soc/qcom/smem_state.h>
> +
> +#include "qcom_common.h"
> +#include "qcom_q6v5.h"
> +#include "remoteproc_internal.h"
> +
> +/* time out value */
> +#define ACK_TIMEOUT			1000
> +#define BOOT_FSM_TIMEOUT		10000
> +/* mask values */
> +#define EVB_MASK			GENMASK(27, 4)
> +/*QDSP6SS register offsets*/
> +#define RST_EVB_REG			0x10
> +#define CORE_START_REG			0x400
> +#define BOOT_CMD_REG			0x404
> +#define BOOT_STATUS_REG			0x408
> +#define RET_CFG_REG			0x1C
> +/*TCSR register offsets*/
> +#define LPASS_MASTER_IDLE_REG		0x8
> +#define LPASS_HALTACK_REG		0x4
> +#define LPASS_PWR_ON_REG		0x10
> +#define LPASS_HALTREQ_REG		0x0
> +
> +/* list of clocks required by ADSP PIL */
> +static const char * const adsp_clk_id[] = {
> +	"sway_cbcr", "lpass_aon", "lpass_ahbs_aon_cbcr", "lpass_ahbm_aon_cbcr",
> +	"qdsp6ss_xo", "qdsp6ss_sleep", "qdsp6ss_core",
> +};
> +
> +struct adsp_pil_data {
> +	int crash_reason_smem;
> +	const char *firmware_name;
> +
> +	const char *ssr_name;
> +	const char *sysmon_name;
> +	int ssctl_id;
> +};
> +
> +struct qcom_adsp {
> +	struct device *dev;
> +	struct rproc *rproc;
> +
> +	struct qcom_q6v5 q6v5;
> +
> +	struct clk *xo;
> +
> +	int num_clks;
> +	struct clk_bulk_data *clks;
> +
> +	void __iomem *qdsp6ss_base;
> +
> +	struct reset_control *pdc_sync_reset;
> +	struct reset_control *cc_lpass_restart;
> +
> +	struct regmap *halt_map;
> +	unsigned int halt_lpass;
> +
> +	int crash_reason_smem;
> +
> +	struct completion start_done;
> +	struct completion stop_done;
> +
> +	phys_addr_t mem_phys;
> +	phys_addr_t mem_reloc;
> +	void *mem_region;
> +	size_t mem_size;
> +
> +	struct qcom_rproc_glink glink_subdev;
> +	struct qcom_rproc_ssr ssr_subdev;
> +	struct qcom_sysmon *sysmon;
> +};
> +
> +static int qcom_adsp_shutdown(struct qcom_adsp *adsp)
> +{
> +	unsigned long timeout;
> +	unsigned int val;
> +	int ret;
> +
> +	/* Reset the retention logic */
> +	val = readl(adsp->qdsp6ss_base + RET_CFG_REG);
> +	val |= 0x1;
> +	writel(val, adsp->qdsp6ss_base + RET_CFG_REG);
> +
> +	clk_bulk_disable_unprepare(adsp->num_clks, adsp->clks);
> +
> +	/* QDSP6 master port needs to be explicitly halted */
> +	ret = regmap_read(adsp->halt_map,
> +			adsp->halt_lpass + LPASS_PWR_ON_REG, &val);
> +	if (ret || !val)
> +		goto reset;
> +
> +	ret = regmap_read(adsp->halt_map,
> +			adsp->halt_lpass + LPASS_MASTER_IDLE_REG,
> +			&val);
> +	if (ret || val)
> +		goto reset;
> +
> +	regmap_write(adsp->halt_map,
> +			adsp->halt_lpass + LPASS_HALTREQ_REG, 1);
> +
> +	/* Wait for halt ACK from QDSP6 */
> +	timeout = jiffies + msecs_to_jiffies(ACK_TIMEOUT);
> +	for (;;) {
> +		ret = regmap_read(adsp->halt_map,
> +			adsp->halt_lpass + LPASS_HALTACK_REG, &val);
> +		if (ret || val || time_after(jiffies, timeout))
> +			break;
> +
> +		usleep_range(1000, 1100);
> +	}
> +
> +	ret = regmap_read(adsp->halt_map,
> +			adsp->halt_lpass + LPASS_MASTER_IDLE_REG, &val);
> +	if (ret || !val)
> +		dev_err(adsp->dev, "port failed halt\n");
> +
> +reset:
> +	/* Assert the LPASS PDC Reset */
> +	reset_control_assert(adsp->pdc_sync_reset);
> +	/* Place the LPASS processor into reset */
> +	reset_control_assert(adsp->cc_lpass_restart);
> +	/* wait after asserting subsystem restart from AOSS */
> +	usleep_range(200, 300);
> +
> +	/* Clear the halt request for the AXIM and AHBM for Q6 */
> +	regmap_write(adsp->halt_map, adsp->halt_lpass + LPASS_HALTREQ_REG, 0);
> +
> +	/* De-assert the LPASS PDC Reset */
> +	reset_control_deassert(adsp->pdc_sync_reset);
> +	/* Remove the LPASS reset */
> +	reset_control_deassert(adsp->cc_lpass_restart);
> +	/* wait after de-asserting subsystem restart from AOSS */
> +	usleep_range(200, 300);
> +
> +	return 0;
> +}
> +
> +static int adsp_load(struct rproc *rproc, const struct firmware *fw)
> +{
> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> +
> +	return qcom_mdt_load_no_init(adsp->dev, fw, rproc->firmware, 0,
> +			     adsp->mem_region, adsp->mem_phys, adsp->mem_size,
> +			     &adsp->mem_reloc);
> +}
> +
> +static int adsp_start(struct rproc *rproc)
> +{
> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> +	int ret;
> +	unsigned int val;
> +
> +	qcom_q6v5_prepare(&adsp->q6v5);
> +
> +	ret = clk_prepare_enable(adsp->xo);
> +	if (ret)
> +		goto disable_irqs;
> +
> +	dev_pm_genpd_set_performance_state(adsp->dev, INT_MAX);
> +	ret = pm_runtime_get_sync(adsp->dev);
> +	if (ret)
> +		goto disable_xo_clk;
> +
> +	ret = clk_bulk_prepare_enable(adsp->num_clks, adsp->clks);
> +	if (ret) {
> +		dev_err(adsp->dev, "adsp clk_enable failed\n");
> +		goto disable_power_domain;
> +	}
> +
> +	/* Program boot address */
> +	writel(adsp->mem_phys >> 4, adsp->qdsp6ss_base + RST_EVB_REG);
> +
> +	/* De-assert QDSP6 stop core. QDSP6 will execute after out of reset */
> +	writel(0x1, adsp->qdsp6ss_base + CORE_START_REG);
> +
> +	/* Trigger boot FSM to start QDSP6 */
> +	writel(0x1, adsp->qdsp6ss_base + BOOT_CMD_REG);
> +
> +	/* Wait for core to come out of reset */
> +	ret = readl_poll_timeout(adsp->qdsp6ss_base + BOOT_STATUS_REG,
> +			val, (val & BIT(0)) != 0, 10, BOOT_FSM_TIMEOUT);
> +	if (ret) {
> +		dev_err(adsp->dev, "failed to bootup adsp\n");
> +		goto disable_adsp_clks;
> +	}
> +
> +	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5 * HZ));
> +	if (ret == -ETIMEDOUT) {
> +		dev_err(adsp->dev, "start timed out\n");
> +		goto disable_adsp_clks;
> +	}
> +
> +	return 0;
> +
> +disable_adsp_clks:
> +	clk_bulk_disable_unprepare(adsp->num_clks, adsp->clks);
> +disable_power_domain:
> +	dev_pm_genpd_set_performance_state(adsp->dev, 0);
> +	pm_runtime_put(adsp->dev);
> +disable_xo_clk:
> +	clk_disable_unprepare(adsp->xo);
> +disable_irqs:
> +	qcom_q6v5_unprepare(&adsp->q6v5);
> +
> +	return ret;
> +}
> +
> +static void qcom_adsp_pil_handover(struct qcom_q6v5 *q6v5)
> +{
> +	struct qcom_adsp *adsp = container_of(q6v5, struct qcom_adsp, q6v5);
> +
> +	clk_disable_unprepare(adsp->xo);
> +	dev_pm_genpd_set_performance_state(adsp->dev, 0);
> +	pm_runtime_put(adsp->dev);
> +}
> +
> +static int adsp_stop(struct rproc *rproc)
> +{
> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> +	int handover;
> +	int ret;
> +
> +	ret = qcom_q6v5_request_stop(&adsp->q6v5);
> +	if (ret == -ETIMEDOUT)
> +		dev_err(adsp->dev, "timed out on wait\n");
> +
> +	ret = qcom_adsp_shutdown(adsp);
> +	if (ret)
> +		dev_err(adsp->dev, "failed to shutdown: %d\n", ret);
> +
> +	handover = qcom_q6v5_unprepare(&adsp->q6v5);
> +	if (handover)
> +		qcom_adsp_pil_handover(&adsp->q6v5);
> +
> +	return ret;
> +}
> +
> +static void *adsp_da_to_va(struct rproc *rproc, u64 da, int len)
> +{
> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> +	int offset;
> +
> +	offset = da - adsp->mem_reloc;
> +	if (offset < 0 || offset + len > adsp->mem_size)
> +		return NULL;
> +
> +	return adsp->mem_region + offset;
> +}
> +
> +static const struct rproc_ops adsp_ops = {
> +	.start = adsp_start,
> +	.stop = adsp_stop,
> +	.da_to_va = adsp_da_to_va,
> +	.parse_fw = qcom_register_dump_segments,
> +	.load = adsp_load,
> +};
> +
> +static int adsp_init_clock(struct qcom_adsp *adsp)
> +{
> +	int i, ret;
> +
> +	adsp->xo = devm_clk_get(adsp->dev, "xo");
> +	if (IS_ERR(adsp->xo)) {
> +		ret = PTR_ERR(adsp->xo);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(adsp->dev, "failed to get xo clock");
> +		return ret;
> +	}
> +
> +	adsp->num_clks = ARRAY_SIZE(adsp_clk_id);
> +	adsp->clks = devm_kcalloc(adsp->dev, adsp->num_clks,
> +				sizeof(*adsp->clks), GFP_KERNEL);
> +	if (IS_ERR(adsp->clks)) {
> +		ret = PTR_ERR(adsp->clks);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(adsp->dev, "failed to get adsp clock");
> +		return ret;
> +	}
> +
> +	for (i = 0; i < adsp->num_clks; i++)
> +		adsp->clks[i].id = adsp_clk_id[i];
> +
> +	return devm_clk_bulk_get(adsp->dev, adsp->num_clks, adsp->clks);
> +}
> +
> +static int adsp_init_reset(struct qcom_adsp *adsp)
> +{
> +	adsp->pdc_sync_reset = devm_reset_control_get_exclusive(adsp->dev,
> +			"pdc_sync");
> +	if (IS_ERR(adsp->pdc_sync_reset)) {
> +		dev_err(adsp->dev, "failed to acquire pdc_sync reset\n");
> +		return PTR_ERR(adsp->pdc_sync_reset);
> +	}
> +
> +	adsp->cc_lpass_restart = devm_reset_control_get_exclusive(adsp->dev,
> +			"cc_lpass");
> +	if (IS_ERR(adsp->cc_lpass_restart)) {
> +		dev_err(adsp->dev, "failed to acquire cc_lpass restart\n");
> +		return PTR_ERR(adsp->cc_lpass_restart);
> +	}
> +
> +	return 0;
> +}
> +
> +static int adsp_init_mmio(struct qcom_adsp *adsp,
> +				struct platform_device *pdev)
> +{
> +	struct device_node *syscon;
> +	struct resource *res;
> +	int ret;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	adsp->qdsp6ss_base = devm_ioremap(&pdev->dev, res->start,
> +			resource_size(res));
> +	if (IS_ERR(adsp->qdsp6ss_base)) {
> +		dev_err(adsp->dev, "failed to map QDSP6SS registers\n");
> +		return PTR_ERR(adsp->qdsp6ss_base);
> +	}
> +
> +	syscon = of_parse_phandle(pdev->dev.of_node, "qcom,halt-regs", 0);
> +	if (!syscon) {
> +		dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n");
> +		return -EINVAL;
> +	}
> +
> +	adsp->halt_map = syscon_node_to_regmap(syscon);
> +	of_node_put(syscon);
> +	if (IS_ERR(adsp->halt_map))
> +		return PTR_ERR(adsp->halt_map);
> +
> +	ret = of_property_read_u32_index(pdev->dev.of_node, "qcom,halt-regs",
> +			1, &adsp->halt_lpass);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "no offset in syscon\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int adsp_alloc_memory_region(struct qcom_adsp *adsp)
> +{
> +	struct device_node *node;
> +	struct resource r;
> +	int ret;
> +
> +	node = of_parse_phandle(adsp->dev->of_node, "memory-region", 0);
> +	if (!node) {
> +		dev_err(adsp->dev, "no memory-region specified\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = of_address_to_resource(node, 0, &r);
> +	if (ret)
> +		return ret;
> +
> +	adsp->mem_phys = adsp->mem_reloc = r.start;
> +	adsp->mem_size = resource_size(&r);
> +	adsp->mem_region = devm_ioremap_wc(adsp->dev,
> +				adsp->mem_phys, adsp->mem_size);
> +	if (!adsp->mem_region) {
> +		dev_err(adsp->dev, "unable to map memory region: %pa+%zx\n",
> +			&r.start, adsp->mem_size);
> +		return -EBUSY;
> +	}
> +
> +	return 0;
> +}
> +
> +static int adsp_probe(struct platform_device *pdev)
> +{
> +	const struct adsp_pil_data *desc;
> +	struct qcom_adsp *adsp;
> +	struct rproc *rproc;
> +	int ret;
> +
> +	desc = of_device_get_match_data(&pdev->dev);
> +	if (!desc)
> +		return -EINVAL;
> +
> +	rproc = rproc_alloc(&pdev->dev, pdev->name, &adsp_ops,
> +			    desc->firmware_name, sizeof(*adsp));
> +	if (!rproc) {
> +		dev_err(&pdev->dev, "unable to allocate remoteproc\n");
> +		return -ENOMEM;
> +	}
> +
> +	adsp = (struct qcom_adsp *)rproc->priv;
> +	adsp->dev = &pdev->dev;
> +	adsp->rproc = rproc;
> +	platform_set_drvdata(pdev, adsp);
> +
> +	ret = adsp_alloc_memory_region(adsp);
> +	if (ret)
> +		goto free_rproc;
> +
> +	ret = adsp_init_clock(adsp);
> +	if (ret)
> +		goto free_rproc;
> +
> +	pm_runtime_enable(adsp->dev);
> +
> +	ret = adsp_init_reset(adsp);
> +	if (ret)
> +		goto disable_pm;
> +
> +	ret = adsp_init_mmio(adsp, pdev);
> +	if (ret)
> +		goto disable_pm;
> +
> +	ret = qcom_q6v5_init(&adsp->q6v5, pdev, rproc, desc->crash_reason_smem,
> +			     qcom_adsp_pil_handover);
> +	if (ret)
> +		goto disable_pm;
> +
> +	qcom_add_glink_subdev(rproc, &adsp->glink_subdev);
> +	qcom_add_ssr_subdev(rproc, &adsp->ssr_subdev, desc->ssr_name);
> +	adsp->sysmon = qcom_add_sysmon_subdev(rproc,
> +					      desc->sysmon_name,
> +					      desc->ssctl_id);
> +
> +	ret = rproc_add(rproc);
> +	if (ret)
> +		goto disable_pm;
> +
> +	return 0;
> +
> +disable_pm:
> +	pm_runtime_disable(adsp->dev);
> +free_rproc:
> +	rproc_free(rproc);
> +
> +	return ret;
> +}
> +
> +static int adsp_remove(struct platform_device *pdev)
> +{
> +	struct qcom_adsp *adsp = platform_get_drvdata(pdev);
> +
> +	rproc_del(adsp->rproc);
> +
> +	qcom_remove_glink_subdev(adsp->rproc, &adsp->glink_subdev);
> +	qcom_remove_sysmon_subdev(adsp->sysmon);
> +	qcom_remove_ssr_subdev(adsp->rproc, &adsp->ssr_subdev);
> +	pm_runtime_disable(adsp->dev);
> +	rproc_free(adsp->rproc);
> +
> +	return 0;
> +}
> +
> +static const struct adsp_pil_data adsp_resource_init = {
> +	.crash_reason_smem = 423,
> +	.firmware_name = "adsp.mdt",
> +	.ssr_name = "lpass",
> +	.sysmon_name = "adsp",
> +	.ssctl_id = 0x14,
> +};
> +
> +static const struct of_device_id adsp_of_match[] = {
> +	{ .compatible = "qcom,sdm845-adsp-pil",
> +	  .data = &adsp_resource_init},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, adsp_of_match);
> +
> +static struct platform_driver adsp_pil_driver = {
> +	.probe = adsp_probe,
> +	.remove = adsp_remove,
> +	.driver = {
> +		.name = "qcom_adsp_pil",
> +		.of_match_table = adsp_of_match,
> +	},
> +};
> +
> +module_platform_driver(adsp_pil_driver);
> +MODULE_DESCRIPTION("QTI SDM845 ADSP Peripheral Image Loader");
> +MODULE_LICENSE("GPL v2");
> -- 
> Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
> is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.
> 

Powered by blists - more mailing lists