| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 10 Oct 2018 16:49:57 +0200
From: Maxime Ripard <maxime.ripard@...tlin.com>
To: Aleksandr Aleksandrov <aleksandr.aleksandrov@...id.com>
Cc: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Chen-Yu Tsai <wens@...e.org>,
Andreas Färber <afaerber@...e.de>,
David Lechner <david@...hnology.com>,
Thierry Reding <treding@...dia.com>,
Noralf Trønnes <noralf@...nnes.org>,
Johan Hovold <johan@...nel.org>, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v3] arm64: new board - Emlid Neutis N5
Hi,
On Mon, Oct 08, 2018 at 06:20:42PM +0300, Aleksandr Aleksandrov wrote:
> Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
> module, DDR3 RAM and eMMC.
>
> - add neutis n5 dtsi file for SoM needs
> - add neutis devboard dts file
> - add neutis devboard target to dtb makefile
> - new vendor prefix - emlid
>
> Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@...id.com>
Your commit prefix is wrong, it should be arm64: dts: allwinner:
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../sun50i-h5-emlid-neutis-n5-devboard.dts | 184 +++++++++++++++++++++
> .../dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi | 96 +++++++++++
> 4 files changed, 282 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 2c3fc51..2336e44 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -112,6 +112,7 @@ edt Emerging Display Technologies
> eeti eGalax_eMPIA Technology Inc
> elan Elan Microelectronic Corp.
> embest Shenzhen Embest Technology Co., Ltd.
> +emlid Emlid, Ltd.
> emmicro EM Microelectronic
> emtrion emtrion GmbH
> energymicro Silicon Laboratories (formerly Energy Micro AS)
This should be in a separate patch.
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 9ffa7a0..eefe74c 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-cc.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts
> new file mode 100644
> index 0000000..493947c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts
> @@ -0,0 +1,184 @@
> +/*
> + * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@...id.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
You should use an SPDX header instead of the full license text.
> +
> +/dts-v1/;
> +
> +#include "sun50i-h5-emlid-neutis-n5.dtsi"
> +
> +/ {
> + model = "Emlid Neutis N5 Developer board";
> + compatible = "emlid,emlid-neutis-n5-devboard",
> + "emlid,emlid-neutis-n5",
Do you need the two emlid there? What comes before the comma is the
vendor, while what is after is the model.
Also, please align those strings
> + "allwinner,sun50i-h5";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + reg_usb0_vbus: usb0-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb0-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
> + status = "okay";
> + };
> +
> + vdd_cpux: gpio-regulator {
> + compatible = "regulator-gpio";
> + pinctrl-names = "default";
> + regulator-name = "vdd-cpux";
> + regulator-type = "voltage";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-ramp-delay = <50>; /* 4ms */
> + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> + gpios-states = <0x1>;
> + states = <1100000 0x0
> + 1300000 0x1>;
> + };
> +};
> +
> +&codec {
> + allwinner,audio-routing =
> + "Line Out", "LINEOUT",
> + "LINEIN", "Line In",
> + "MIC1", "Mic",
> + "MIC2", "Mic",
> + "Mic", "MBIAS";
> + status = "okay";
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&ehci2 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&ohci2 {
> + status = "okay";
> +};
> +
> +&ohci3 {
> + status = "okay";
> +};
> +
> +&emac {
> + phy-handle = <&int_mii_phy>;
> + phy-mode = "mii";
> + allwinner,leds-active-low;
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
> + usb0_vbus-supply = <®_usb0_vbus>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi
> new file mode 100644
> index 0000000..8e1e37d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi
> @@ -0,0 +1,96 @@
> +/*
> + * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@...id.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h5.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + reg_vcc3v3: vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
> + post-power-on-delay-ms = <200>;
> + };
> +};
> +
> +&mmc1 {
> + vmmc-supply = <®_vcc3v3>;
> + vqmmc-supply = <®_vcc3v3>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + interrupt-parent = <&r_pio>;
> + interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_8bit_pins>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <8>;
> + non-removable;
> + cap-mmc-hw-reset;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> + status = "okay";
> +};
I guess this is for bluetooth? Have you tested serdev drivers?
Also, I have a general comments, and it really depends on what your
intention about the board ecosystem is. Do you expect the SOM to be
swappable in multiple boards, or do you expect to send it as something
that is just fixed into a daughter board?
In the former case, you probably want to use overlays instead. In the
latter, you're fine.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Powered by blists - more mailing lists