Message-ID: <20181012220835.GA14259@bogus>
Date:   Fri, 12 Oct 2018 17:08:35 -0500
From:   Rob Herring <robh@...nel.org>
To:     Charles Keepax <ckeepax@...nsource.cirrus.com>
Cc:     lee.jones@...aro.org, mturquette@...libre.com, sboyd@...nel.org,
        broonie@...nel.org, linus.walleij@...aro.org, mark.rutland@....com,
        lgirdwood@...il.com, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, patches@...nsource.cirrus.com,
        linux-clk@...r.kernel.org, linux-gpio@...r.kernel.org
Subject: Re: [PATCH v2 1/5] mfd: lochnagar: Add initial binding documentation

On Mon, Oct 08, 2018 at 02:25:38PM +0100, Charles Keepax wrote:
> Lochnagar is an evaluation and development board for Cirrus
> Logic Smart CODEC and Amp devices. It allows the connection of
> most Cirrus Logic devices on mini-cards, as well as allowing
> connection of various application processor systems to provide a
> full evaluation platform. This driver supports the board
> controller chip on the Lochnagar board.
> 
> Signed-off-by: Charles Keepax <ckeepax@...nsource.cirrus.com>
> ---
> 
> Changes since v1:
>  - Move the binding includes into this patch.
>  - Move patch to the start of the patch chain.
>  - Update commit message a little
> 
> Thanks,
> Charles
> 
>  .../devicetree/bindings/mfd/cirrus,lochnagar.txt   | 230 +++++++++++++++++++++
>  include/dt-bindings/clk/lochnagar.h                |  33 +++
>  include/dt-bindings/pinctrl/lochnagar.h            | 132 ++++++++++++
>  3 files changed, 395 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
>  create mode 100644 include/dt-bindings/clk/lochnagar.h
>  create mode 100644 include/dt-bindings/pinctrl/lochnagar.h

A few nits, otherwise:

Acked-by: Rob Herring <robh@...nel.org>

> 
> diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
> new file mode 100644
> index 0000000000000..3382a14c19fe4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
> @@ -0,0 +1,230 @@
> +Cirrus Logic Lochnagar Audio Development Board
> +
> +Lochnagar is an evaluation and development board for Cirrus Logic
> +Smart CODEC and Amp devices. It allows the connection of most Cirrus
> +Logic devices on mini-cards, as well as allowing connection of
> +various application processor systems to provide a full evaluation
> +platform.  Audio system topology, clocking and power can all be
> +controlled through the Lochnagar, allowing the device under test
> +to be used in a variety of possible use cases.
> +
> +Also see these documents for generic binding information:
> +  [1] GPIO : ../gpio/gpio.txt
> +  [2] Pinctrl: ../pinctrl/pinctrl-bindings.txt
> +  [3] Clock : ../clock/clock-bindings.txt
> +  [4] Regulator: ../regulator/regulator.txt
> +
> +And these for relevant defines:
> +  [5] include/dt-bindings/pinctrl/lochnagar.h
> +  [6] include/dt-bindings/clock/lochnagar.h
> +
> +Required properties:
> +
> +  - compatible : One of the following strings:
> +                 "cirrus,lochnagar1"
> +                 "cirrus,lochnagar2"
> +
> +  - reg : I2C slave address
> +
> +  - gpio-controller : Indicates this device is a GPIO controller.
> +  - #gpio-cells : Must be 2. The first cell is the pin number, see
> +    [5] for available pins and the second cell is used to specify
> +    optional parameters, see [1].
> +  - gpio-ranges : Range of pins managed by the GPIO controller, see
> +    [1]. Both the GPIO and Pinctrl base should be set to zero and the
> +    count to the appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define,
> +    see [5].
> +
> +  - reset-gpios : Reset line to the Lochnagar, see [1].
> +
> +  - #clock-cells : Must be 1. The first cell indicates the clock
> +    number, see [6] for available clocks and [3].
> +
> +  - pinctrl-names : A pinctrl state named "default" must be defined.
> +  - pinctrl-0 : A phandle to the default pinctrl state.
> +
> +  - SYSVDD-supply: Primary power supply for the Lochnagar.
> +
> +Optional properties:
> +
> +  - present-gpios : Host present line, indicating the presence of a
> +    host system, see [1]. This can be omitted if the present line is
> +    tied in hardware.
> +
> +  - clocks : Must contain an entry for each clock in clock-names.
> +  - clock-names : May contain entries for each of the following
> +    clocks:
> +     - ln-cdc-clkout : Output clock from CODEC card.
> +     - ln-dsp-clkout : Output clock from DSP card.
> +     - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional
> +       input audio clocks from host system.
> +     - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from
> +       external connector.
> +     - ln-spdif-clkout : Optional input audio clock from SPDIF.
> +     - ln-adat-clkout : Optional input audio clock from ADAT.
> +
> +  - assigned-clocks : A list of Lochnagar clocks to be reparented, see
> +    [6] for available clocks.
> +  - assigned-clock-parents : Parents to be assigned to the clocks
> +    listed in "assigned-clocks".
> +
> +  - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
> +    MICxVDD outputs, supplying the digital microphones, normally
> +    supplied from the attached CODEC.
> +
> +Required sub-nodes:
> +
> +The pin configurations are defined as a child of the pinctrl states
> +node, see [2]. Each sub-node can have the following properties:
> +  - groups : A list of groups to select (either this or "pins" must be
> +    specified), available groups:
> +      codec-aif1, codec-aif2, codec-aif3, dsp-aif1, dsp-aif2, psia1,
> +      psia2, gf-aif1, gf-aif2, gf-aif3, gf-aif4, spdif-aif, usb-aif1,
> +      usb-aif2, adat-aif, soundcard-aif
> +  - pins : A list of pin names to select (either this or "groups" must
> +    be specified), available pins:
> +      fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
> +      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
> +      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
> +      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
> +      gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat,
> +      codec-aif1-lrclk, codec-aif1-txdat, codec-aif2-bclk,
> +      codec-aif2-rxdat, codec-aif2-lrclk, codec-aif2-txdat,
> +      codec-aif3-bclk, codec-aif3-rxdat, codec-aif3-lrclk,
> +      codec-aif3-txdat, dsp-aif1-bclk, dsp-aif1-rxdat, dsp-aif1-lrclk,
> +      dsp-aif1-txdat, dsp-aif2-bclk, dsp-aif2-rxdat,
> +      dsp-aif2-lrclk, dsp-aif2-txdat, psia1-bclk, psia1-rxdat,
> +      psia1-lrclk, psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk,
> +      psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat, gf-aif3-lrclk,
> +      gf-aif3-txdat, gf-aif4-bclk, gf-aif4-rxdat, gf-aif4-lrclk,
> +      gf-aif4-txdat, gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk,
> +      gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat, gf-aif2-lrclk,
> +      gf-aif2-txdat, dsp-uart1-rx, dsp-uart1-tx, dsp-uart2-rx,
> +      dsp-uart2-tx, gf-uart2-rx, gf-uart2-tx, usb-uart-rx,
> +      codec-pdmclk1, codec-pdmdat1, codec-pdmclk2, codec-pdmdat2,
> +      codec-dmicclk1, codec-dmicdat1, codec-dmicclk2, codec-dmicdat2,
> +      codec-dmicclk3, codec-dmicdat3, codec-dmicclk4, codec-dmicdat4,
> +      dsp-dmicclk1, dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl,
> +      i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, dsp-standby,
> +      codec-mclk1, codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk,
> +      gf-gpio1, gf-gpio5, dsp-gpio20, led1, led2
> +  - function : The mux function to select, available functions:
> +      aif, fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
> +      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
> +      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
> +      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
> +      gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout,
> +      dsp-clkout, pmic-32k, spdif-clkout, clk-12m288, clk-11m2986,
> +      clk-24m576, clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1,
> +      gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1, codec-mclk2,
> +      dsp-clkin, psia1-mclk, psia2-mclk, spdif-mclk, codec-irq,
> +      codec-reset, dsp-reset, dsp-irq, dsp-standby, codec-pdmclk1,
> +      codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, codec-dmicclk1,
> +      codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, codec-dmicclk3,
> +      codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1,
> +      dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx,
> +      dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx, gf-uart2-rx,
> +      gf-uart2-tx, usb-uart-rx, usb-uart-tx, i2c2-scl, i2c2-sda,
> +      i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, gpio, spdif-aif, psia1,
> +      psia1-bclk, psia1-lrclk, psia1-rxdat, psia1-txdat, psia2,
> +      psia2-bclk, psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1,
> +      codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat,
> +      codec-aif1-txdat, codec-aif2, codec-aif2-bclk, codec-aif2-lrclk,
> +      codec-aif2-rxdat, codec-aif2-txdat, codec-aif3, codec-aif3-bclk,
> +      codec-aif3-lrclk, codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1,
> +      dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat, dsp-aif1-txdat,
> +      dsp-aif2, dsp-aif2-bclk, dsp-aif2-lrclk, dsp-aif2-rxdat,
> +      dsp-aif2-txdat, gf-aif3, gf-aif3-bclk, gf-aif3-lrclk,
> +      gf-aif3-rxdat, gf-aif3-txdat, gf-aif4, gf-aif4-bclk,
> +      gf-aif4-lrclk, gf-aif4-rxdat, gf-aif4-txdat, gf-aif1,
> +      gf-aif1-bclk, gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat,
> +      gf-aif2, gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat,
> +      gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif, soundcard-aif,
> +
> +  - aif-master : Specifies that an AIF group will be used as a master
> +    interface (either this or aif-slave is required if a group is
> +    being muxed to an AIF)
> +  - aif-slave : Specifies that an AIF group will be used as a slave
> +    interface (either this or aif-master is required if a group is
> +    being muxed to an AIF)

Vendor prefix needed on these.

> +
> +Optional sub-nodes:
> +
> +  - VDDCORE : Initialisation data for the VDDCORE regulator, which
> +    supplies the CODECs digital core if it has no build regulator for that
> +    purpose.
> +
> +  - MICVDD : Initialisation data for the MICVDD regulator, which
> +    supplies the CODECs MICVDD.
> +  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
> +      Optional Properties:
> +      - cirrus,micbias-input : A property selecting which of the CODEC
> +        minicard micbias outputs should be used, valid values are 1 - 4.
> +
> +  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
> +    CODECs analog and 1.8V digital supplies.
> +      Required Properties:
> +      - compatible : Should be set to "regulator-fixed"
> +      - regulator-min-microvolt : Should be set to 1.8V
> +      - regulator-max-microvolt : Should be set to 1.8V
> +      - regulator-boot-on
> +      - regulator-always-on
> +      - vin-supply : Should be set to same supply as SYSVDD
> +
> +Example:
> +lochnagar: lochnagar@22 {
> +	compatible = "cirrus,lochnagar2";
> +	reg = <0x22>;
> +
> +	gpio-controller;
> +	#gpio-cells = <2>;
> +	gpio-ranges = <&lochnagar 0 0 110>;
> +
> +	reset-gpio = <&gpio0 55 0>;
> +	present-gpio = <&gpio0 60 0>;

-gpios

> +
> +	#clock-cells = <1>;
> +
> +	clocks = <&clk_audio>;
> +	clock-names = "ln-gf-mclk2";
> +
> +	assigned-clocks = <&lochnagar LOCHNAGAR_CDC_MCLK1>,
> +			  <&lochnagar LOCHNAGAR_CDC_MCLK2>;
> +	assigned-clock-parents = <&clk_audio>,
> +				 <&lochnagar LOCHNAGAR_PMIC_32K>;
> +
> +	SYSVDD-supply = <&wallvdd>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pin_settings>;
> +
> +	pin_settings: pin_settings {
> +		ap_aif {
> +			aif-slave;

Use '-' rather than '_' on node names.

> +			groups = "gf-aif1";
> +			function = "codec-aif3";
> +		};
> +		codec_aif {
> +			aif-master;
> +			groups = "codec-aif3";
> +			function = "gf-aif1";
> +		};
> +	};
> +
> +	lochnagar_micvdd: MICVDD {
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	lochnagar_vdd1v8: VDD1V8 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VDD1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +
> +		vin-supply = <&wallvdd>;
> +	};
> +};
> diff --git a/include/dt-bindings/clk/lochnagar.h b/include/dt-bindings/clk/lochnagar.h
> new file mode 100644
> index 0000000000000..caeeec7dfbf6d
> --- /dev/null
> +++ b/include/dt-bindings/clk/lochnagar.h
> @@ -0,0 +1,33 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Device Tree defines for Lochnagar clocking
> + *
> + * Copyright (c) 2017-2018 Cirrus Logic, Inc. and
> + *                         Cirrus Logic International Semiconductor Ltd.
> + *
> + * Author: Charles Keepax <ckeepax@...nsource.cirrus.com>
> + */
> +
> +#ifndef DT_BINDINGS_CLK_LOCHNAGAR_H
> +#define DT_BINDINGS_CLK_LOCHNAGAR_H
> +
> +#define LOCHNAGAR_CDC_MCLK1		0
> +#define LOCHNAGAR_CDC_MCLK2		1
> +#define LOCHNAGAR_DSP_CLKIN		2
> +#define LOCHNAGAR_GF_CLKOUT1		3
> +#define LOCHNAGAR_GF_CLKOUT2		4
> +#define LOCHNAGAR_PSIA1_MCLK		5
> +#define LOCHNAGAR_PSIA2_MCLK		6
> +#define LOCHNAGAR_SPDIF_MCLK		7
> +#define LOCHNAGAR_ADAT_MCLK		8
> +#define LOCHNAGAR_SOUNDCARD_MCLK	9
> +#define LOCHNAGAR_PMIC_32K		10
> +#define LOCHNAGAR_CLK_12M		11
> +#define LOCHNAGAR_CLK_11M		12
> +#define LOCHNAGAR_CLK_24M		13
> +#define LOCHNAGAR_CLK_22M		14
> +#define LOCHNAGAR_USB_CLK_24M		15
> +#define LOCHNAGAR_USB_CLK_12M		16
> +#define LOCHNAGAR_SPDIF_CLKOUT		17
> +
> +#endif
> diff --git a/include/dt-bindings/pinctrl/lochnagar.h b/include/dt-bindings/pinctrl/lochnagar.h
> new file mode 100644
> index 0000000000000..644760bf5725b
> --- /dev/null
> +++ b/include/dt-bindings/pinctrl/lochnagar.h
> @@ -0,0 +1,132 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Device Tree defines for Lochnagar pinctrl
> + *
> + * Copyright (c) 2018 Cirrus Logic, Inc. and
> + *                    Cirrus Logic International Semiconductor Ltd.
> + *
> + * Author: Charles Keepax <ckeepax@...nsource.cirrus.com>
> + */
> +
> +#ifndef DT_BINDINGS_PINCTRL_LOCHNAGAR_H
> +#define DT_BINDINGS_PINCTRL_LOCHNAGAR_H
> +
> +#define LOCHNAGAR1_PIN_CDC_RESET		0
> +#define LOCHNAGAR1_PIN_DSP_RESET		1
> +#define LOCHNAGAR1_PIN_CDC_CIF1MODE		2
> +#define LOCHNAGAR1_PIN_NUM_GPIOS		3
> +
> +#define LOCHNAGAR2_PIN_CDC_RESET		0
> +#define LOCHNAGAR2_PIN_DSP_RESET		1
> +#define LOCHNAGAR2_PIN_CDC_CIF1MODE		2
> +#define LOCHNAGAR2_PIN_CDC_LDOENA		3
> +#define LOCHNAGAR2_PIN_SPDIF_HWMODE		4
> +#define LOCHNAGAR2_PIN_SPDIF_RESET		5
> +#define LOCHNAGAR2_PIN_FPGA_GPIO1		6
> +#define LOCHNAGAR2_PIN_FPGA_GPIO2		7
> +#define LOCHNAGAR2_PIN_FPGA_GPIO3		8
> +#define LOCHNAGAR2_PIN_FPGA_GPIO4		9
> +#define LOCHNAGAR2_PIN_FPGA_GPIO5		10
> +#define LOCHNAGAR2_PIN_FPGA_GPIO6		11
> +#define LOCHNAGAR2_PIN_CDC_GPIO1		12
> +#define LOCHNAGAR2_PIN_CDC_GPIO2		13
> +#define LOCHNAGAR2_PIN_CDC_GPIO3		14
> +#define LOCHNAGAR2_PIN_CDC_GPIO4		15
> +#define LOCHNAGAR2_PIN_CDC_GPIO5		16
> +#define LOCHNAGAR2_PIN_CDC_GPIO6		17
> +#define LOCHNAGAR2_PIN_CDC_GPIO7		18
> +#define LOCHNAGAR2_PIN_CDC_GPIO8		19
> +#define LOCHNAGAR2_PIN_DSP_GPIO1		20
> +#define LOCHNAGAR2_PIN_DSP_GPIO2		21
> +#define LOCHNAGAR2_PIN_DSP_GPIO3		22
> +#define LOCHNAGAR2_PIN_DSP_GPIO4		23
> +#define LOCHNAGAR2_PIN_DSP_GPIO5		24
> +#define LOCHNAGAR2_PIN_DSP_GPIO6		25
> +#define LOCHNAGAR2_PIN_GF_GPIO2			26
> +#define LOCHNAGAR2_PIN_GF_GPIO3			27
> +#define LOCHNAGAR2_PIN_GF_GPIO7			28
> +#define LOCHNAGAR2_PIN_CDC_AIF1_BCLK		29
> +#define LOCHNAGAR2_PIN_CDC_AIF1_RXDAT		30
> +#define LOCHNAGAR2_PIN_CDC_AIF1_LRCLK		31
> +#define LOCHNAGAR2_PIN_CDC_AIF1_TXDAT		32
> +#define LOCHNAGAR2_PIN_CDC_AIF2_BCLK		33
> +#define LOCHNAGAR2_PIN_CDC_AIF2_RXDAT		34
> +#define LOCHNAGAR2_PIN_CDC_AIF2_LRCLK		35
> +#define LOCHNAGAR2_PIN_CDC_AIF2_TXDAT		36
> +#define LOCHNAGAR2_PIN_CDC_AIF3_BCLK		37
> +#define LOCHNAGAR2_PIN_CDC_AIF3_RXDAT		38
> +#define LOCHNAGAR2_PIN_CDC_AIF3_LRCLK		39
> +#define LOCHNAGAR2_PIN_CDC_AIF3_TXDAT		40
> +#define LOCHNAGAR2_PIN_DSP_AIF1_BCLK		41
> +#define LOCHNAGAR2_PIN_DSP_AIF1_RXDAT		42
> +#define LOCHNAGAR2_PIN_DSP_AIF1_LRCLK		43
> +#define LOCHNAGAR2_PIN_DSP_AIF1_TXDAT		44
> +#define LOCHNAGAR2_PIN_DSP_AIF2_BCLK		45
> +#define LOCHNAGAR2_PIN_DSP_AIF2_RXDAT		46
> +#define LOCHNAGAR2_PIN_DSP_AIF2_LRCLK		47
> +#define LOCHNAGAR2_PIN_DSP_AIF2_TXDAT		48
> +#define LOCHNAGAR2_PIN_PSIA1_BCLK		49
> +#define LOCHNAGAR2_PIN_PSIA1_RXDAT		50
> +#define LOCHNAGAR2_PIN_PSIA1_LRCLK		51
> +#define LOCHNAGAR2_PIN_PSIA1_TXDAT		52
> +#define LOCHNAGAR2_PIN_PSIA2_BCLK		53
> +#define LOCHNAGAR2_PIN_PSIA2_RXDAT		54
> +#define LOCHNAGAR2_PIN_PSIA2_LRCLK		55
> +#define LOCHNAGAR2_PIN_PSIA2_TXDAT		56
> +#define LOCHNAGAR2_PIN_GF_AIF3_BCLK		57
> +#define LOCHNAGAR2_PIN_GF_AIF3_RXDAT		58
> +#define LOCHNAGAR2_PIN_GF_AIF3_LRCLK		59
> +#define LOCHNAGAR2_PIN_GF_AIF3_TXDAT		60
> +#define LOCHNAGAR2_PIN_GF_AIF4_BCLK		61
> +#define LOCHNAGAR2_PIN_GF_AIF4_RXDAT		62
> +#define LOCHNAGAR2_PIN_GF_AIF4_LRCLK		63
> +#define LOCHNAGAR2_PIN_GF_AIF4_TXDAT		64
> +#define LOCHNAGAR2_PIN_GF_AIF1_BCLK		65
> +#define LOCHNAGAR2_PIN_GF_AIF1_RXDAT		66
> +#define LOCHNAGAR2_PIN_GF_AIF1_LRCLK		67
> +#define LOCHNAGAR2_PIN_GF_AIF1_TXDAT		68
> +#define LOCHNAGAR2_PIN_GF_AIF2_BCLK		69
> +#define LOCHNAGAR2_PIN_GF_AIF2_RXDAT		70
> +#define LOCHNAGAR2_PIN_GF_AIF2_LRCLK		71
> +#define LOCHNAGAR2_PIN_GF_AIF2_TXDAT		72
> +#define LOCHNAGAR2_PIN_DSP_UART1_RX		73
> +#define LOCHNAGAR2_PIN_DSP_UART1_TX		74
> +#define LOCHNAGAR2_PIN_DSP_UART2_RX		75
> +#define LOCHNAGAR2_PIN_DSP_UART2_TX		76
> +#define LOCHNAGAR2_PIN_GF_UART2_RX		77
> +#define LOCHNAGAR2_PIN_GF_UART2_TX		78
> +#define LOCHNAGAR2_PIN_USB_UART_RX		79
> +#define LOCHNAGAR2_PIN_CDC_PDMCLK1		80
> +#define LOCHNAGAR2_PIN_CDC_PDMDAT1		81
> +#define LOCHNAGAR2_PIN_CDC_PDMCLK2		82
> +#define LOCHNAGAR2_PIN_CDC_PDMDAT2		83
> +#define LOCHNAGAR2_PIN_CDC_DMICCLK1		84
> +#define LOCHNAGAR2_PIN_CDC_DMICDAT1		85
> +#define LOCHNAGAR2_PIN_CDC_DMICCLK2		86
> +#define LOCHNAGAR2_PIN_CDC_DMICDAT2		87
> +#define LOCHNAGAR2_PIN_CDC_DMICCLK3		88
> +#define LOCHNAGAR2_PIN_CDC_DMICDAT3		89
> +#define LOCHNAGAR2_PIN_CDC_DMICCLK4		90
> +#define LOCHNAGAR2_PIN_CDC_DMICDAT4		91
> +#define LOCHNAGAR2_PIN_DSP_DMICCLK1		92
> +#define LOCHNAGAR2_PIN_DSP_DMICDAT1		93
> +#define LOCHNAGAR2_PIN_DSP_DMICCLK2		94
> +#define LOCHNAGAR2_PIN_DSP_DMICDAT2		95
> +#define LOCHNAGAR2_PIN_I2C2_SCL			96
> +#define LOCHNAGAR2_PIN_I2C2_SDA			97
> +#define LOCHNAGAR2_PIN_I2C3_SCL			98
> +#define LOCHNAGAR2_PIN_I2C3_SDA			99
> +#define LOCHNAGAR2_PIN_I2C4_SCL			100
> +#define LOCHNAGAR2_PIN_I2C4_SDA			101
> +#define LOCHNAGAR2_PIN_DSP_STANDBY		102
> +#define LOCHNAGAR2_PIN_CDC_MCLK1		103
> +#define LOCHNAGAR2_PIN_CDC_MCLK2		104
> +#define LOCHNAGAR2_PIN_DSP_CLKIN		105
> +#define LOCHNAGAR2_PIN_PSIA1_MCLK		106
> +#define LOCHNAGAR2_PIN_PSIA2_MCLK		107
> +#define LOCHNAGAR2_PIN_GF_GPIO1			108
> +#define LOCHNAGAR2_PIN_GF_GPIO5			109
> +#define LOCHNAGAR2_PIN_DSP_GPIO20		110
> +#define LOCHNAGAR2_PIN_NUM_GPIOS		111
> +
> +#endif
> -- 
> 2.11.0
> 

Powered by blists - more mailing lists