| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <86789d73-5a6c-7729-ecd1-dcd342b2fcde@amlogic.com>
Date: Sat, 3 Nov 2018 15:29:24 +0800
From: Jianxin Pan <jianxin.pan@...ogic.com>
To: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
CC: <jbrunet@...libre.com>, Neil Armstrong <narmstrong@...libre.com>,
<yixun.lan@...ogic.com>, <khilman@...libre.com>,
<carlo@...one.org>, <mturquette@...libre.com>, <sboyd@...nel.org>,
<robh@...nel.org>, <miquel.raynal@...tlin.com>,
<boris.brezillon@...tlin.com>, <liang.yang@...ogic.com>,
<jian.hu@...ogic.com>, <qiufang.dai@...ogic.com>,
<hanjie.lin@...ogic.com>, <victor.wan@...ogic.com>,
<linux-clk@...r.kernel.org>, <linux-amlogic@...ts.infradead.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v6 3/3] clk: meson: add sub MMC clock controller driver
Hi Martin,
Thanks for the review and suggestion. Please see my comments below.
On 2018/11/2 2:16, Martin Blumenstingl wrote:
> Hi Jianxin,
>
> On Thu, Nov 1, 2018 at 5:31 PM Jianxin Pan <jianxin.pan@...ogic.com> wrote:
>>
>> From: Yixun Lan <yixun.lan@...ogic.com>
>>
>> The patch will add a MMC clock controller driver which used by MMC or NAND,
>> It provide a mux and divider clock, and three phase clocks - core, tx, tx.
>>
>> Two clocks are provided as the parent of MMC clock controller from
>> upper layer clock controller - eg "amlogic,axg-clkc" in AXG platform.
>>
>> To specify which clock the MMC or NAND driver may consume,
>> the preprocessor macros in the dt-bindings/clock/amlogic,mmc-clkc.h header
>> can be used in the device tree sources.
>>
>> Signed-off-by: Yixun Lan <yixun.lan@...ogic.com>
>> Signed-off-by: Jianxin Pan <jianxin.pan@...ogic.com>
> this looks good to me in general, some comments below
>
>> ---
>> drivers/clk/meson/Kconfig | 10 ++
>> drivers/clk/meson/Makefile | 1 +
>> drivers/clk/meson/clk-regmap.c | 1 -
>> drivers/clk/meson/mmc-clkc.c | 310 +++++++++++++++++++++++++++++++++++++++++
>> 4 files changed, 321 insertions(+), 1 deletion(-)
>> create mode 100644 drivers/clk/meson/mmc-clkc.c
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index efaa70f..6bb0d44 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -15,6 +15,16 @@ config COMMON_CLK_MESON_AO
>> select COMMON_CLK_REGMAP_MESON
>> select RESET_CONTROLLER
>>
>> +config COMMON_CLK_MMC_MESON
>> + tristate "Meson MMC Sub Clock Controller Driver"
>> + select MFD_SYSCON
>> + select COMMON_CLK_AMLOGIC
>> + select COMMON_CLK_AMLOGIC_AUDIO
>> + help
>> + Support for the MMC sub clock controller on Amlogic Meson Platform,
>> + which include S905 (GXBB, GXL), A113D/X (AXG) devices.
> can you confirm that (in the future) we will be able to use this with
> G12A and G12B as well?
Yes, this part can be reused in G12A and G12B two.
>
>> + Say Y if you want this clock enabled.
>> +
>> config COMMON_CLK_REGMAP_MESON
>> bool
>> select REGMAP
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 39ce566..31c16d5 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -9,4 +9,5 @@ obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-32k.o
>> obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>> +obj-$(CONFIG_COMMON_CLK_MMC_MESON) += mmc-clkc.o
>> obj-$(CONFIG_COMMON_CLK_REGMAP_MESON) += clk-regmap.o
>> diff --git a/drivers/clk/meson/clk-regmap.c b/drivers/clk/meson/clk-regmap.c
>> index 305ee30..89cee4a 100644
>> --- a/drivers/clk/meson/clk-regmap.c
>> +++ b/drivers/clk/meson/clk-regmap.c
>> @@ -114,7 +114,6 @@ static int clk_regmap_div_set_rate(struct clk_hw *hw, unsigned long rate,
>> };
>>
>> /* Would prefer clk_regmap_div_ro_ops but clashes with qcom */
>> -
> unnecessary whitespace change, personally I would drop this file from the patch
OK, I will remove the unnecessary whitespace change here.
Thanks for your time.
>
>> const struct clk_ops clk_regmap_divider_ops = {
>> .recalc_rate = clk_regmap_div_recalc_rate,
>> .round_rate = clk_regmap_div_round_rate,
>> diff --git a/drivers/clk/meson/mmc-clkc.c b/drivers/clk/meson/mmc-clkc.c
>> new file mode 100644
>> index 0000000..a3e4c91
>> --- /dev/null
>> +++ b/drivers/clk/meson/mmc-clkc.c
>> @@ -0,0 +1,310 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Amlogic Meson MMC Sub Clock Controller Driver
>> + *
>> + * Copyright (c) 2017 Baylibre SAS.
>> + * Author: Jerome Brunet <jbrunet@...libre.com>
>> + *
>> + * Copyright (c) 2018 Amlogic, inc.
>> + * Author: Yixun Lan <yixun.lan@...ogic.com>
>> + * Author: Jianxin Pan <jianxin.pan@...ogic.com>
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/clk-provider.h>
>> +#include <linux/module.h>
>> +#include <linux/regmap.h>
>> +#include <linux/slab.h>
>> +#include <linux/of_device.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/platform_device.h>
>> +#include <dt-bindings/clock/amlogic,mmc-clkc.h>
>> +
>> +#include "clkc.h"
>> +#include "clkc-audio.h"
>> +
>> +/* clock ID used by internal driver */
>> +#define CLKID_MMC_MUX 0
>> +
>> +#define SD_EMMC_CLOCK 0
>> +#define CLK_DELAY_STEP_PS 200
>> +#define CLK_PHASE_STEP 30
>> +#define CLK_PHASE_POINT_NUM (360 / CLK_PHASE_STEP)
> CLK_PHASE_STEP and CLK_PHASE_POINT_NUM are unused
YES, I will remove them.
>> +
>> +#define MUX_CLK_NUM_PARENTS 2
>> +#define MMC_MAX_CLKS 5
>> +
>> +struct mmc_clkc_data {
>> + struct meson_clk_phase_delay_data tx;
>> + struct meson_clk_phase_delay_data rx;
>> +};
>> +
>> +static struct clk_regmap_mux_data mmc_clkc_mux_data = {
>> + .offset = SD_EMMC_CLOCK,
>> + .mask = 0x3,
>> + .shift = 6,
>> +};
>> +
>> +struct meson_sclk_div_data mmc_clkc_div_data = {
> can this be const?
The member cached_div need to be changed danymicly in clk ops.
In addition, there are more than one instances of the controller, so I will alloc them danymicly.
> also there are two whitespaces after meson_sclk_div_data
OK, I will remove it.
>> + .div = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = (0),
>> + .width = (6),
>> + },
>> + .hi = {
>> + .reg_off = 0,
>> + .shift = 0,
>> + .width = 0,
>> + },
>> +};
>> +
>> +static struct meson_clk_phase_data mmc_clkc_core_phase = {
>> + .ph = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 8,
>> + .width = 2,
>> + }
>> +};
>> +
>> +static const struct mmc_clkc_data mmc_clkc_gx_data = {
>> + .tx = {
>> + .phase = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 10,
>> + .width = 2,
>> + },
>> + .delay = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 16,
>> + .width = 4,
>> + },
>> + .delay_step_ps = CLK_DELAY_STEP_PS,
>> + },
>> + .rx = {
>> + .phase = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 12,
>> + .width = 2,
>> + },
>> + .delay = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 20,
>> + .width = 4,
>> + },
>> + .delay_step_ps = CLK_DELAY_STEP_PS,
>> + },
>> +};
>> +
>> +static const struct mmc_clkc_data mmc_clkc_axg_data = {
>> + .tx = {
>> + .phase = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 10,
>> + .width = 2,
>> + },
>> + .delay = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 16,
>> + .width = 6,
>> + },
>> + .delay_step_ps = CLK_DELAY_STEP_PS,
>> + },
>> + .rx = {
>> + .phase = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 12,
>> + .width = 2,
>> + },
>> + .delay = {
>> + .reg_off = SD_EMMC_CLOCK,
>> + .shift = 22,
>> + .width = 6,
>> + },
>> + .delay_step_ps = CLK_DELAY_STEP_PS,
>> + },
>> +};
>> +
>> +static const struct of_device_id mmc_clkc_match_table[] = {
>> + {
>> + .compatible = "amlogic,gx-mmc-clkc",
>> + .data = &mmc_clkc_gx_data
>> + },
>> + {
>> + .compatible = "amlogic,axg-mmc-clkc",
>> + .data = &mmc_clkc_axg_data
>> + },
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(of, mmc_clkc_match_table);
>> +
>> +static struct clk_regmap *
>> +mmc_clkc_register_clk(struct device *dev, struct regmap *map,
>> + struct clk_init_data *init,
>> + const char *suffix, void *data)
>> +{
>> + struct clk_regmap *clk;
>> + char *name;
>> + int ret;
>> +
>> + clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
>> + if (!clk)
>> + return ERR_PTR(-ENOMEM);
>> +
>> + name = kasprintf(GFP_KERNEL, "%s#%s", dev_name(dev), suffix);
> use devm_kasprintf here? this will allow you to get rid of the kfree below
mmc_clkc_register_clk need to kfree(name) when it returns.
But devm_kasprintf will keep the memory until the device is removed.
Thanks for your time.
>> + if (!name)
>> + return ERR_PTR(-ENOMEM);
>> +
>> + init->name = name;
>> +
>> + clk->map = map;
>> + clk->data = data;
>> + clk->hw.init = init;
>> +
>> + ret = devm_clk_hw_register(dev, &clk->hw);
>> + if (ret)
>> + clk = ERR_PTR(ret);
>> +
>> + kfree(name);
>> + return clk;
>> +}
>> +
>> +static struct clk_regmap *mmc_clkc_register_mux(struct device *dev,
>> + struct regmap *map)
>> +{
>> + const char *parent_names[MUX_CLK_NUM_PARENTS];
>> + struct clk_init_data init;
>> + struct clk_regmap *mux;
>> + struct clk *clk;
>> + int i;
>> +
>> + for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
>> + char name[8];
>> +
>> + snprintf(name, sizeof(name), "clkin%d", i);
>> + clk = devm_clk_get(dev, name);
>> + if (IS_ERR(clk)) {
>> + if (clk != ERR_PTR(-EPROBE_DEFER))
>> + dev_err(dev, "Missing clock %s\n", name);
>> + return ERR_PTR((long)clk);
>> + }
>> +
>> + parent_names[i] = __clk_get_name(clk);
>> + }
>> +
>> + init.ops = &clk_regmap_mux_ops;
>> + init.flags = CLK_SET_RATE_PARENT;
>> + init.parent_names = parent_names;
>> + init.num_parents = MUX_CLK_NUM_PARENTS;
>> +
>> + mux = mmc_clkc_register_clk(dev, map, &init, "mux", &mmc_clkc_mux_data);
>> + if (IS_ERR(mux))
>> + dev_err(dev, "Mux clock registration failed\n");
>> +
>> + return mux;
>> +}
>> +
>> +static struct clk_regmap *
>> +mmc_clkc_register_clk_with_parent(struct device *dev, struct regmap *map,
>> + char *suffix, const struct clk_hw *hw,
>> + unsigned long flags,
>> + const struct clk_ops *ops, void *data)
>> +{
>> + struct clk_init_data init;
>> + struct clk_regmap *clk;
>> + const char *parent_name = clk_hw_get_name(hw);
>> +
>> + init.ops = ops;
>> + init.flags = flags;
>> + init.parent_names = &parent_name;
>> + init.num_parents = 1;
>> +
>> + clk = mmc_clkc_register_clk(dev, map, &init, suffix, data);
>> + if (IS_ERR(clk))
>> + dev_err(dev, "Core %s clock registration failed\n", suffix);
>> +
>> + return clk;
>> +}
>> +
>> +static int mmc_clkc_probe(struct platform_device *pdev)
>> +{
>> + struct clk_hw_onecell_data *onecell_data;
>> + struct device *dev = &pdev->dev;
>> + struct mmc_clkc_data *data;
>> + struct regmap *map;
>> + struct clk_regmap *clk, *core;
>> +
>> + /*cast to drop the const in match->data*/
>> + data = (struct mmc_clkc_data *)of_device_get_match_data(dev);
> can you declare the data variable as "const struct mmc_clkc_data
> *data;" instead?
&data->rx and &data->tx are saved as 'data' member in struct clk_regmap. And it's not a const variable.
struct clk_regmap {
struct clk_hw hw;
struct regmap *map;
void *data;
};
mmc_clkc_register_clk_with_parent(..., void *data) is shared with other clocks,and the *data for mmc_clkc_div_data is not const.
>
>> + if (!data)
>> + return -ENODEV;
>> +
>> + map = syscon_node_to_regmap(dev->of_node);
>> + if (IS_ERR(map)) {
>> + dev_err(dev, "could not find mmc clock controller\n");
>> + return PTR_ERR(map);
>> + }
>> +
>> + onecell_data = devm_kzalloc(dev, sizeof(*onecell_data) +
>> + sizeof(*onecell_data->hws) * MMC_MAX_CLKS,
>> + GFP_KERNEL);
>> + if (!onecell_data)
>> + return -ENOMEM;
>> +
>> + clk = mmc_clkc_register_mux(dev, map);
>> + if (IS_ERR(clk))
>> + return PTR_ERR(clk);
>> + onecell_data->hws[CLKID_MMC_MUX] = &clk->hw,
>> +
>> + clk = mmc_clkc_register_clk_with_parent(dev, map, "div",
>> + &clk->hw,
>> + CLK_SET_RATE_PARENT,
>> + &meson_sclk_div_ops,
>> + &mmc_clkc_div_data);
>> + if (IS_ERR(clk))
>> + return PTR_ERR(clk);
>> + onecell_data->hws[CLKID_MMC_DIV] = &clk->hw,
>> +
>> + core = mmc_clkc_register_clk_with_parent(dev, map, "core",
>> + &clk->hw,
>> + CLK_SET_RATE_PARENT,
>> + &meson_clk_phase_ops,
>> + &mmc_clkc_core_phase);
>> + if (IS_ERR(core))
>> + return PTR_ERR(core);
>> + onecell_data->hws[CLKID_MMC_PHASE_CORE] = &core->hw,
>> +
>> + clk = mmc_clkc_register_clk_with_parent(dev, map, "rx",
>> + &core->hw, 0,
>> + &meson_clk_phase_delay_ops,
>> + &data->rx);
>> + if (IS_ERR(clk))
>> + return PTR_ERR(clk);
>> + onecell_data->hws[CLKID_MMC_PHASE_RX] = &clk->hw,
>> +
>> + clk = mmc_clkc_register_clk_with_parent(dev, map, "tx",
>> + &core->hw, 0,
>> + &meson_clk_phase_delay_ops,
>> + &data->tx);
>> + if (IS_ERR(clk))
>> + return PTR_ERR(clk);
>> + onecell_data->hws[CLKID_MMC_PHASE_TX] = &clk->hw,
>> +
>> + onecell_data->num = MMC_MAX_CLKS;
>> +
>> + return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
>> + onecell_data);
>> +}
>> +
>> +static struct platform_driver mmc_clkc_driver = {
>> + .probe = mmc_clkc_probe,
>> + .driver = {
>> + .name = "meson-mmc-clkc",
>> + .of_match_table = of_match_ptr(mmc_clkc_match_table),
>> + },
>> +};
>> +
>> +module_platform_driver(mmc_clkc_driver);
>> +
>> +MODULE_DESCRIPTION("Amlogic AXG MMC clock driver");
>> +MODULE_AUTHOR("Jianxin Pan <jianxin.pan@...ogic.com>");
>> +MODULE_LICENSE("GPL v2");
>> --
>> 1.9.1
>>
>
> Regards
> Martin
>
> .
>
Powered by blists - more mailing lists