lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20181105120219.03ab3b4c@bbrezillon>
Date:   Mon, 5 Nov 2018 12:02:19 +0100
From:   Boris Brezillon <boris.brezillon@...tlin.com>
To:     Piotr Bugalski <bugalski.piotr@...il.com>
Cc:     Mark Brown <broonie@...nel.org>, linux-spi@...r.kernel.org,
        David Woodhouse <dwmw2@...radead.org>,
        Brian Norris <computersforpeace@...il.com>,
        Marek Vasut <marek.vasut@...il.com>,
        Richard Weinberger <richard@....at>,
        linux-mtd@...ts.infradead.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        devicetree@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Nicolas Ferre <nicolas.ferre@...rochip.com>,
        Alexandre Belloni <alexandre.belloni@...tlin.com>,
        Cyrille Pitchen <cyrille.pitchen@...rochip.com>,
        Tudor Ambarus <tudor.ambarus@...rochip.com>
Subject: Re: [PATCH v3 0/6] New QuadSPI driver for Atmel SAMA5D2

Hi Piotr,

On Mon,  5 Nov 2018 11:36:19 +0100
Piotr Bugalski <bugalski.piotr@...il.com> wrote:

> Hello,
> 
> Atmel SAMA5D2 is equipped with two QSPI interfaces. These interfaces can
> work as in SPI-compatible mode or use two / four lines to improve
> communication speed. At the moment there is QSPI driver strongly tied to
> NOR-flash memory and MTD subsystem.
> Intention of this change is to provide new driver which will not be tied
> to MTD and allows using QSPI with NAND-flash memory or other peripherals
> New spi-mem API provides abstraction layer which can disconnect QSPI
> from MTD. This driver doesn't support regular SPI interface, it should
> be used with spi-mem interface only.
> Unfortunately SAMA5D2 hardware by default supports only NOR-flash
> memory. It allows 24- and 32-bit addressing while NAND-flash requires
> 16-bit long. To workaround hardware limitation driver is a bit more
> complicated.
> 
> Request to spi-mem contains three fiels: opcode (command), address,
> dummy bytes. SAMA5D2 QSPI hardware supports opcode, address, dummy and
> option byte where address field can only be 24- or 32- bytes long.
> Handling 8-bits long addresses is done using option field. For 16-bits
> address behaviour depends of number of requested dummy bits. If there
> are 8 or more dummy cycles, address is shifted and sent with first dummy
> byte. Otherwise opcode is disabled and first byte of address contains
> command opcode (works only if opcode and address use the same buswidth).
> The limitation is when 16-bit address is used without enough dummy
> cycles and opcode is using different buswidth than address. Other modes
> are supported with described workaround.
> 
> It looks like hardware has some limitation in performance. The same issue
> exists in current QSPI driver (MTD/nor-flash) and soft-pack (bare-metal
> library from Atmel). Without using DMA read speed is much worse than
> maximum bandwidth (efficiency 30-40%). Any help with performance
> improvement is highly welcome, especially for NAND-flash memories which
> offers higher capacity than NOR-flash used with previous driver.

I think you can try to implement the dirmap interface proposed here [1]
and use DMA+TRSFR_READ/WRITE_MEMORY for such direct mappings. This
should optimize path where we really matter about perfs.

> 
> Best Regards,
> Piotr
> 
> v3 changes:
>  - add get_name implementation
>  - email address fix
> 
> v2 changes:
>  - driver is now replacement of existing atmel-quadspi
>  - code was re-written to follow original code structure
>  - deinitialization order fixed
>  - empty atmel_qspi_adjust_op_size function removed
>  - code formatting fixes
>  - use spi_device->max_speed_hz to get spi speed
>  - spi freqency set in spi_controller->setup() hook
>  - address range checkng for 4-bytes addressing
>  - use timeout to avoid infinite waiting
> 
> Piotr Bugalski (6):
>   mtd: spi-nor: atmel-quaspi: Typo fix
>   mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi
>   mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi
>     driver
>   mtd: spi-nor: atmel-quadspi: Remove unused code from atmel-quadspi
>     driver
>   spi: Add QuadSPI driver for Atmel SAMA5D2
>   dt-bindings: spi: QuadSPI driver for Atmel SAMA5D2

The patch series is

Acked-by: Boris Brezillon <boris.brezillon@...tlin.com>

Mark, if you're okay with the new implementation, would you mind taking
those patches in the spi tree?

Thanks,

Boris

[1]http://patchwork.ozlabs.org/project/linux-mtd/list/?series=73235

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ