[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20181111221629.851793510@linuxfoundation.org>
Date: Sun, 11 Nov 2018 14:16:57 -0800
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Yu Zhao <yuzhao@...gle.com>,
Ulf Hansson <ulf.hansson@...aro.org>,
Sasha Levin <sashal@...nel.org>
Subject: [PATCH 4.19 070/361] mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Yu Zhao <yuzhao@...gle.com>
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ]
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603
mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077
mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================
The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: Yu Zhao <yuzhao@...gle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@...aro.org>
Signed-off-by: Sasha Levin <sashal@...nel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/mmc/host/sdhci-pci-o2micro.c | 3 +++
1 file changed, 3 insertions(+)
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -490,6 +490,9 @@ int sdhci_pci_o2_probe(struct sdhci_pci_
pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
break;
case PCI_DEVICE_ID_O2_SEABIRD0:
+ if (chip->pdev->revision == 0x01)
+ chip->quirks |= SDHCI_QUIRK_DELAY_AFTER_POWER;
+ /* fall through */
case PCI_DEVICE_ID_O2_SEABIRD1:
/* UnLock WP */
ret = pci_read_config_byte(chip->pdev,
Powered by blists - more mailing lists