| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1542412619-387-8-git-send-email-jollys@xilinx.com>
Date: Fri, 16 Nov 2018 15:56:57 -0800
From: Jolly Shah <jolly.shah@...inx.com>
To: <robh+dt@...nel.org>, <mark.rutland@....com>
CC: <michal.simek@...inx.com>, <rajanv@...inx.com>,
<nava.manne@...inx.com>, <linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
Jolly Shah <jollys@...inx.com>,
Anurag Kumar Vulisha <anuragku@...inx.com>
Subject: [PATCH 7/9] dt-bindings: phy: Add dt bindings for ZynqMP PHY
This patch adds the document describing dt bindings for ZynqMP
PHY. ZynqMP SOC has a High Speed Processing System Gigabit
Transceiver which provides PHY capabilties to USB, SATA,
PCIE, Display Port and Ehernet SGMII controllers.
Signed-off-by: Anurag Kumar Vulisha <anuragku@...inx.com>
Signed-off-by: Jolly Shah <jollys@...inx.com>
Signed-off-by: Michal Simek <michal.simek@...inx.com>
---
.../devicetree/bindings/phy/phy-zynqmp.txt | 126 +++++++++++++++++++++
1 file changed, 126 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-zynqmp.txt
diff --git a/Documentation/devicetree/bindings/phy/phy-zynqmp.txt b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
new file mode 100644
index 0000000..21cb722
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
@@ -0,0 +1,126 @@
+Xilinx ZynqMP PHY binding
+
+This binding describes a ZynqMP PHY device that is used to control ZynqMP
+High Speed Gigabit Transceiver(GT). ZynqMP PS GTR provides four lanes
+and are used by USB, SATA, PCIE, Display port and Ethernet SGMMI controllers.
+
+Required properties (controller (parent) node):
+- compatible : Can be "xlnx,zynqmp-psgtr-v1.1" or "xlnx,zynqmp-psgtr"
+ "xlnx,zynqmp-psgtr-v1.1" has the lpd address mapping removed
+
+- reg : Address and length of register sets for each device in
+ "reg-names"
+- reg-names : The names of the register addresses corresponding to the
+ registers filled in "reg":
+ - serdes: SERDES block register set
+ - siou: SIOU block register set
+ - lpd: Low power domain peripherals reset control
+
+Required nodes : A sub-node is required for each lane the controller
+ provides.
+
+Required properties (port (child) nodes):
+lane0:
+- #phy-cells : Should be 4
+ Cell after port phandle is device type from:
+ - <PHY_TYPE_PCIE 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SATA 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_USB3 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_DP 1 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SGMII 0 LANE_NUM FREQUENCY>
+lane1:
+- #phy-cells : Should be 4
+ Cell after port phandle is device type from:
+ - <PHY_TYPE_PCIE 1 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SATA 1 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_USB3 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_DP 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SGMII 1 LANE_NUM FREQUENCY>
+lane2:
+- #phy-cells : Should be 4
+ Cell after port phandle is device type from:
+ - <PHY_TYPE_PCIE 2 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SATA 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_USB3 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_DP 1 LANE_NUM FREQUENC>
+ - <PHY_TYPE_SGMII 2 LANE_NUM FREQUENCY>
+lane3:
+- #phy-cells : Should be 4
+ Cell after port phandle is device type from:
+ - <PHY_TYPE_PCIE 3 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SATA 1 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_USB3 1 LANE_NUM FREQUENCY >
+ - <PHY_TYPE_DP 0 LANE_NUM FREQUENCY>
+ - <PHY_TYPE_SGMII 3 LANE_NUM FREQUENCY>
+
+Note: LANE_NUM : This determines which lane's reference clock is shared by controller.
+ FREQUENCY: This the clock frequency at which controller wants to operate.
+
+
+Example:
+firmware {
+ zynqmp_firmware: zynqmp-firmware {
+ compatible = "xlnx,zynqmp-firmware";
+ method = "smc";
+
+ serdes: zynqmp_phy@...00000 {
+ compatible = "xlnx,zynqmp-psgtr";
+ status = "okay";
+ reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 0x0 0x1000>,
+ <0x0 0xff5e0000 0x0 0x1000>;
+ reg-names = "serdes", "siou", "lpd";
+
+ lane0: lane@0 {
+ #phy-cells = <4>;
+ };
+ lane1: lane@1 {
+ #phy-cells = <4>;
+ };
+ lane2: lane@2 {
+ #phy-cells = <4>;
+ };
+ lane3: lane@3 {
+ #phy-cells = <4>;
+ };
+ };
+ };
+};
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type.
+
+phys = <PHANDLE CONTROLLER_TYPE CONTROLLER_INSTANCE LANE_NUM LANE_FREQ>;
+
+PHANDLE = &lane0 or &lane1 or &lane2 or &lane3
+CONTROLLER_TYPE = PHY_TYPE_PCIE or PHY_TYPE_SATA or PHY_TYPE_USB
+ or PHY_TYPE_DP or PHY_TYPE_SGMII
+CONTROLLER_INSTANCE = Depends on controller type used, can be any of
+ PHY_TYPE_PCIE : 0 or 1 or 2 or 3
+ PHY_TYPE_SATA : 0 or 1
+ PHY_TYPE_USB : 0 or 1
+ PHY_TYPE_DP : 0 or 1
+ PHY_TYPE_SGMII: 0 or 1 or 2 or 3
+LANE_NUM = Depends on which lane clock is used as ref clk, can be
+ 0 or 1 or 2 or 3
+LANE_FREQ = Frequency that controller can operate, can be any of
+ 19.2Mhz,20Mhz,24Mhz,26Mhz,27Mhz,28.4Mhz,40Mhz,52Mhz,
+ 100Mhz,108Mhz,125Mhz,135Mhz,150Mhz
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+ usb@...00000 {
+ ...
+ phys = <&lane2 PHY_TYPE_USB3 0 2 2600000>;
+ ...
+ };
+
+ ahci@...c0000 {
+ ...
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ ...
+ };
--
2.7.4
Powered by blists - more mailing lists