linux-kernel - [PATCH 5/5] Bluetooth: btusb: Use the hw_reset method to allow resetting the BT chip

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20181117010748.24347-6-rajatja@google.com>
Date:   Fri, 16 Nov 2018 17:07:48 -0800
From:   Rajat Jain <rajatja@...gle.com>
To:     Marcel Holtmann <marcel@...tmann.org>,
        Johan Hedberg <johan.hedberg@...il.com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        "David S. Miller" <davem@...emloft.net>,
        Dmitry Torokhov <dtor@...omium.org>,
        Rajat Jain <rajatja@...gle.com>,
        Alex Hung <alex.hung@...onical.com>,
        linux-bluetooth@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-usb@...r.kernel.org, netdev@...r.kernel.org
Cc:     rajatxjain@...il.com, dtor@...gle.com, raghuram.hegde@...el.com,
        chethan.tumkur.narayan@...el.com, sukumar.ghorai@...el.com
Subject: [PATCH 5/5] Bluetooth: btusb: Use the hw_reset method to allow
 resetting the BT chip

If the platform provides it, use the reset gpio to reset the BT
chip (requested by the HCI core if needed). This has been found helpful
on some of Intel bluetooth controllers where the firmware gets stuck and
the only way out is a hard reset pin provided by the platform.

Signed-off-by: Rajat Jain <rajatja@...gle.com>
---
 drivers/bluetooth/btusb.c | 36 ++++++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index e8e148480c91..8aad02d9e211 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -29,6 +29,7 @@
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
 #include <linux/suspend.h>
+#include <linux/gpio/consumer.h>
 #include <asm/unaligned.h>
 
 #include <net/bluetooth/bluetooth.h>
@@ -475,6 +476,8 @@ struct btusb_data {
 	struct usb_endpoint_descriptor *diag_tx_ep;
 	struct usb_endpoint_descriptor *diag_rx_ep;
 
+	struct gpio_desc *reset_gpio;
+
 	__u8 cmdreq_type;
 	__u8 cmdreq;
 
@@ -490,6 +493,28 @@ struct btusb_data {
 	int oob_wake_irq;   /* irq for out-of-band wake-on-bt */
 };
 
+
+static void btusb_hw_reset(struct hci_dev *hdev)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	struct gpio_desc *reset_gpio = data->reset_gpio;
+
+	/*
+	 * Toggle the hard reset line if the platform provides one. The reset
+	 * is going to yank the device off the USB and then replug. So doing
+	 * once is enough. The cleanup is handled correctly on the way out
+	 * (standard USB disconnect), and the new device is detected cleanly
+	 * and bound to the driver again like it should be.
+	 */
+	if (reset_gpio) {
+		bt_dev_dbg(hdev, "%s: Initiating HW reset via gpio", __func__);
+		clear_bit(HCI_QUIRK_HW_RESET_ON_TIMEOUT, &hdev->quirks);
+		gpiod_set_value(reset_gpio, 1);
+		mdelay(100);
+		gpiod_set_value(reset_gpio, 0);
+	}
+}
+
 static inline void btusb_free_frags(struct btusb_data *data)
 {
 	unsigned long flags;
@@ -3030,6 +3055,11 @@ static int btusb_probe(struct usb_interface *intf,
 
 	SET_HCIDEV_DEV(hdev, &intf->dev);
 
+	data->reset_gpio = gpiod_get_optional(&data->udev->dev, "reset",
+					      GPIOD_OUT_LOW);
+	if (data->reset_gpio)
+		hdev->hw_reset = btusb_hw_reset;
+
 	hdev->open   = btusb_open;
 	hdev->close  = btusb_close;
 	hdev->flush  = btusb_flush;
@@ -3085,6 +3115,7 @@ static int btusb_probe(struct usb_interface *intf,
 		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
 		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
+		set_bit(HCI_QUIRK_HW_RESET_ON_TIMEOUT, &hdev->quirks);
 
 		if (id->driver_info & BTUSB_INTEL) {
 			hdev->setup = btusb_setup_intel;
@@ -3225,6 +3256,8 @@ static int btusb_probe(struct usb_interface *intf,
 	return 0;
 
 out_free_dev:
+	if (data->reset_gpio)
+		gpiod_put(data->reset_gpio);
 	hci_free_dev(hdev);
 	return err;
 }
@@ -3268,6 +3301,9 @@ static void btusb_disconnect(struct usb_interface *intf)
 	if (data->oob_wake_irq)
 		device_init_wakeup(&data->udev->dev, false);
 
+	if (data->reset_gpio)
+		gpiod_put(data->reset_gpio);
+
 	hci_free_dev(hdev);
 }
 
-- 
2.19.1.1215.g8438c0b245-goog