| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20181214234646.21359-1-slongerbeam@gmail.com>
Date: Fri, 14 Dec 2018 15:46:46 -0800
From: Steve Longerbeam <slongerbeam@...il.com>
To: linux-media@...r.kernel.org
Cc: Steve Longerbeam <slongerbeam@...il.com>,
Philipp Zabel <p.zabel@...gutronix.de>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
dri-devel@...ts.freedesktop.org (open list:DRM DRIVERS FOR FREESCALE
IMX), linux-kernel@...r.kernel.org (open list),
devel@...verdev.osuosl.org (open list:STAGING SUBSYSTEM),
linux-fbdev@...r.kernel.org (open list:FRAMEBUFFER LAYER)
Subject: [PATCH v6] gpu: ipu-csi: Swap fields according to input/output field types
The function ipu_csi_init_interface() was inverting the F-bit for
NTSC case, in the CCIR_CODE_1/2 registers. The result being that
for NTSC bottom-top field order, the CSI would swap fields and
capture in top-bottom order.
Instead, base field swap on the field order of the input to the CSI,
and the field order of the requested output. If the input/output
fields are sequential but different, swap fields, otherwise do
not swap. This requires passing both the input and output mbus
frame formats to ipu_csi_init_interface().
Move this code to a new private function ipu_csi_set_bt_interlaced_codes()
that programs the CCIR_CODE_1/2 registers for interlaced BT.656 (and
possibly interlaced BT.1120 in the future).
When detecting input video standard from the input frame width/height,
make sure to double height if input field type is alternate, since
in that case input height only includes lines for one field.
Signed-off-by: Steve Longerbeam <slongerbeam@...il.com>
Reviewed-by: Philipp Zabel <p.zabel@...gutronix.de>
---
Changes since v5:
- Convert to const the infmt, outfmt, and mbus_cfg pointer args to
ipu_csi_init_interface(), suggested by Philipp Zabel.
- Bring back if_fmt local var and don't copy outfmt to local stack in
csi_setup(), suggested by Philipp.
Changes since v4:
- Cleaned up some convoluted code in ipu_csi_init_interface(), suggested
by Philipp.
- Fixed a regression in csi_setup(), caught by Philipp.
---
drivers/gpu/ipu-v3/ipu-csi.c | 126 +++++++++++++++-------
drivers/staging/media/imx/imx-media-csi.c | 7 +-
include/video/imx-ipu-v3.h | 5 +-
3 files changed, 89 insertions(+), 49 deletions(-)
diff --git a/drivers/gpu/ipu-v3/ipu-csi.c b/drivers/gpu/ipu-v3/ipu-csi.c
index aa0e30a2ba18..d1e575571a8d 100644
--- a/drivers/gpu/ipu-v3/ipu-csi.c
+++ b/drivers/gpu/ipu-v3/ipu-csi.c
@@ -325,12 +325,21 @@ static int mbus_code_to_bus_cfg(struct ipu_csi_bus_config *cfg, u32 mbus_code,
return 0;
}
+/* translate alternate field mode based on given standard */
+static inline enum v4l2_field
+ipu_csi_translate_field(enum v4l2_field field, v4l2_std_id std)
+{
+ return (field != V4L2_FIELD_ALTERNATE) ? field :
+ ((std & V4L2_STD_525_60) ?
+ V4L2_FIELD_SEQ_BT : V4L2_FIELD_SEQ_TB);
+}
+
/*
* Fill a CSI bus config struct from mbus_config and mbus_framefmt.
*/
static int fill_csi_bus_cfg(struct ipu_csi_bus_config *csicfg,
- struct v4l2_mbus_config *mbus_cfg,
- struct v4l2_mbus_framefmt *mbus_fmt)
+ const struct v4l2_mbus_config *mbus_cfg,
+ const struct v4l2_mbus_framefmt *mbus_fmt)
{
int ret;
@@ -374,22 +383,76 @@ static int fill_csi_bus_cfg(struct ipu_csi_bus_config *csicfg,
return 0;
}
+static int
+ipu_csi_set_bt_interlaced_codes(struct ipu_csi *csi,
+ const struct v4l2_mbus_framefmt *infmt,
+ const struct v4l2_mbus_framefmt *outfmt,
+ v4l2_std_id std)
+{
+ enum v4l2_field infield, outfield;
+ bool swap_fields;
+
+ /* get translated field type of input and output */
+ infield = ipu_csi_translate_field(infmt->field, std);
+ outfield = ipu_csi_translate_field(outfmt->field, std);
+
+ /*
+ * Write the H-V-F codes the CSI will match against the
+ * incoming data for start/end of active and blanking
+ * field intervals. If input and output field types are
+ * sequential but not the same (one is SEQ_BT and the other
+ * is SEQ_TB), swap the F-bit so that the CSI will capture
+ * field 1 lines before field 0 lines.
+ */
+ swap_fields = (V4L2_FIELD_IS_SEQUENTIAL(infield) &&
+ V4L2_FIELD_IS_SEQUENTIAL(outfield) &&
+ infield != outfield);
+
+ if (!swap_fields) {
+ /*
+ * Field0BlankEnd = 110, Field0BlankStart = 010
+ * Field0ActiveEnd = 100, Field0ActiveStart = 000
+ * Field1BlankEnd = 111, Field1BlankStart = 011
+ * Field1ActiveEnd = 101, Field1ActiveStart = 001
+ */
+ ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
+ CSI_CCIR_CODE_1);
+ ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
+ } else {
+ dev_dbg(csi->ipu->dev, "capture field swap\n");
+
+ /* same as above but with F-bit inverted */
+ ipu_csi_write(csi, 0xD07DF | CSI_CCIR_ERR_DET_EN,
+ CSI_CCIR_CODE_1);
+ ipu_csi_write(csi, 0x40596, CSI_CCIR_CODE_2);
+ }
+
+ ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
+
+ return 0;
+}
+
+
int ipu_csi_init_interface(struct ipu_csi *csi,
- struct v4l2_mbus_config *mbus_cfg,
- struct v4l2_mbus_framefmt *mbus_fmt)
+ const struct v4l2_mbus_config *mbus_cfg,
+ const struct v4l2_mbus_framefmt *infmt,
+ const struct v4l2_mbus_framefmt *outfmt)
{
struct ipu_csi_bus_config cfg;
unsigned long flags;
u32 width, height, data = 0;
+ v4l2_std_id std;
int ret;
- ret = fill_csi_bus_cfg(&cfg, mbus_cfg, mbus_fmt);
+ ret = fill_csi_bus_cfg(&cfg, mbus_cfg, infmt);
if (ret < 0)
return ret;
/* set default sensor frame width and height */
- width = mbus_fmt->width;
- height = mbus_fmt->height;
+ width = infmt->width;
+ height = infmt->height;
+ if (infmt->field == V4L2_FIELD_ALTERNATE)
+ height *= 2;
/* Set the CSI_SENS_CONF register remaining fields */
data |= cfg.data_width << CSI_SENS_CONF_DATA_WIDTH_SHIFT |
@@ -416,42 +479,22 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
break;
case IPU_CSI_CLK_MODE_CCIR656_INTERLACED:
- if (mbus_fmt->width == 720 && mbus_fmt->height == 576) {
- /*
- * PAL case
- *
- * Field0BlankEnd = 0x6, Field0BlankStart = 0x2,
- * Field0ActiveEnd = 0x4, Field0ActiveStart = 0
- * Field1BlankEnd = 0x7, Field1BlankStart = 0x3,
- * Field1ActiveEnd = 0x5, Field1ActiveStart = 0x1
- */
- height = 625; /* framelines for PAL */
-
- ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
- CSI_CCIR_CODE_1);
- ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
- ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
- } else if (mbus_fmt->width == 720 && mbus_fmt->height == 480) {
- /*
- * NTSC case
- *
- * Field0BlankEnd = 0x7, Field0BlankStart = 0x3,
- * Field0ActiveEnd = 0x5, Field0ActiveStart = 0x1
- * Field1BlankEnd = 0x6, Field1BlankStart = 0x2,
- * Field1ActiveEnd = 0x4, Field1ActiveStart = 0
- */
- height = 525; /* framelines for NTSC */
-
- ipu_csi_write(csi, 0xD07DF | CSI_CCIR_ERR_DET_EN,
- CSI_CCIR_CODE_1);
- ipu_csi_write(csi, 0x40596, CSI_CCIR_CODE_2);
- ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
+ if (width == 720 && height == 480) {
+ std = V4L2_STD_NTSC;
+ height = 525;
+ } else if (width == 720 && height == 576) {
+ std = V4L2_STD_PAL;
+ height = 625;
} else {
dev_err(csi->ipu->dev,
- "Unsupported CCIR656 interlaced video mode\n");
- spin_unlock_irqrestore(&csi->lock, flags);
- return -EINVAL;
+ "Unsupported interlaced video mode\n");
+ ret = -EINVAL;
+ goto out_unlock;
}
+
+ ret = ipu_csi_set_bt_interlaced_codes(csi, infmt, outfmt, std);
+ if (ret)
+ goto out_unlock;
break;
case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_DDR:
case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_SDR:
@@ -476,9 +519,10 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
dev_dbg(csi->ipu->dev, "CSI_ACT_FRM_SIZE = 0x%08X\n",
ipu_csi_read(csi, CSI_ACT_FRM_SIZE));
+out_unlock:
spin_unlock_irqrestore(&csi->lock, flags);
- return 0;
+ return ret;
}
EXPORT_SYMBOL_GPL(ipu_csi_init_interface);
diff --git a/drivers/staging/media/imx/imx-media-csi.c b/drivers/staging/media/imx/imx-media-csi.c
index 4223f8d418ae..c2a8d9cd31b7 100644
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -679,12 +679,7 @@ static int csi_setup(struct csi_priv *priv)
priv->upstream_ep.bus.parallel.flags :
priv->upstream_ep.bus.mipi_csi2.flags;
- /*
- * we need to pass input frame to CSI interface, but
- * with translated field type from output format
- */
if_fmt = *infmt;
- if_fmt.field = outfmt->field;
crop = priv->crop;
/*
@@ -702,7 +697,7 @@ static int csi_setup(struct csi_priv *priv)
priv->crop.width == 2 * priv->compose.width,
priv->crop.height == 2 * priv->compose.height);
- ipu_csi_init_interface(priv->csi, &mbus_cfg, &if_fmt);
+ ipu_csi_init_interface(priv->csi, &mbus_cfg, &if_fmt, outfmt);
ipu_csi_set_dest(priv->csi, priv->dest);
diff --git a/include/video/imx-ipu-v3.h b/include/video/imx-ipu-v3.h
index abbad94e14a1..f5568ac87306 100644
--- a/include/video/imx-ipu-v3.h
+++ b/include/video/imx-ipu-v3.h
@@ -351,8 +351,9 @@ int ipu_prg_channel_configure(struct ipuv3_channel *ipu_chan,
*/
struct ipu_csi;
int ipu_csi_init_interface(struct ipu_csi *csi,
- struct v4l2_mbus_config *mbus_cfg,
- struct v4l2_mbus_framefmt *mbus_fmt);
+ const struct v4l2_mbus_config *mbus_cfg,
+ const struct v4l2_mbus_framefmt *infmt,
+ const struct v4l2_mbus_framefmt *outfmt);
bool ipu_csi_is_interlaced(struct ipu_csi *csi);
void ipu_csi_get_window(struct ipu_csi *csi, struct v4l2_rect *w);
void ipu_csi_set_window(struct ipu_csi *csi, struct v4l2_rect *w);
--
2.17.1
Powered by blists - more mailing lists