| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <324f3106dbff2f28baae098b05219f1384fda97a.1547559542.git.baolin.wang@linaro.org>
Date: Tue, 15 Jan 2019 21:46:53 +0800
From: Baolin Wang <baolin.wang@...aro.org>
To: broonie@...nel.org, robh+dt@...nel.org, mark.rutland@....com
Cc: orsonzhai@...il.com, zhang.lyra@...il.com, lanqing.liu@...soc.com,
baolin.wang@...aro.org, linux-spi@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH 4/4] spi: sprd: Add DMA mode support
From: Lanqing Liu <lanqing.liu@...eadtrum.com>
Add DMA mode support for the Spreadtrum SPI controller, and we will enable
SPI interrupt to help to complete the SPI transfer work in DMA mode.
Signed-off-by: Lanqing Liu <lanqing.liu@...eadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@...aro.org>
---
drivers/spi/spi-sprd.c | 291 +++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 288 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-sprd.c b/drivers/spi/spi-sprd.c
index bfba30b..da93016 100644
--- a/drivers/spi/spi-sprd.c
+++ b/drivers/spi/spi-sprd.c
@@ -2,6 +2,9 @@
// Copyright (C) 2018 Spreadtrum Communications Inc.
#include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma/sprd-dma.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
@@ -9,6 +12,7 @@
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
+#include <linux/of_dma.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>
@@ -128,9 +132,26 @@
#define SPRD_SPI_DEFAULT_SOURCE 26000000
#define SPRD_SPI_MAX_SPEED_HZ 48000000
#define SPRD_SPI_AUTOSUSPEND_DELAY 100
+#define SPRD_SPI_DMA_STEP 8
+
+enum sprd_spi_dma_channel {
+ SPI_RX,
+ SPI_TX,
+ SPI_MAX,
+};
+
+struct sprd_spi_dma {
+ bool enable;
+ struct dma_chan *dma_chan[SPI_MAX];
+ u32 slave_id[SPI_MAX];
+ enum dma_slave_buswidth width;
+ u32 fragmens_len;
+ u32 rx_len;
+};
struct sprd_spi {
void __iomem *base;
+ phys_addr_t phy_base;
struct device *dev;
struct clk *clk;
int irq;
@@ -142,6 +163,7 @@ struct sprd_spi {
u32 hw_speed_hz;
u32 len;
int status;
+ struct sprd_spi_dma dma;
struct completion xfer_completion;
const void *tx_buf;
void *rx_buf;
@@ -433,6 +455,186 @@ static int sprd_spi_txrx_bufs(struct spi_device *sdev, struct spi_transfer *t)
return ret;
}
+static void sprd_spi_dma_enable(struct sprd_spi *ss, bool enable)
+{
+ u32 val = readl_relaxed(ss->base + SPRD_SPI_CTL2);
+
+ if (enable)
+ val |= SPRD_SPI_DMA_EN;
+ else
+ val &= ~SPRD_SPI_DMA_EN;
+
+ writel_relaxed(val, ss->base + SPRD_SPI_CTL2);
+}
+
+static int sprd_spi_dma_submit(struct dma_chan *dma_chan,
+ struct dma_slave_config *c,
+ struct sg_table *sg,
+ enum dma_transfer_direction dir)
+{
+ struct dma_async_tx_descriptor *desc;
+ dma_cookie_t cookie;
+ unsigned long flags;
+ int ret;
+
+ ret = dmaengine_slave_config(dma_chan, c);
+ if (ret < 0)
+ return ret;
+
+ flags = SPRD_DMA_FLAGS(SPRD_DMA_CHN_MODE_NONE, SPRD_DMA_NO_TRG,
+ SPRD_DMA_FRAG_REQ, SPRD_DMA_TRANS_INT);
+ desc = dmaengine_prep_slave_sg(dma_chan, sg->sgl, sg->nents, dir, flags);
+ if (!desc)
+ return -ENODEV;
+
+ cookie = dmaengine_submit(desc);
+ if (dma_submit_error(cookie))
+ return dma_submit_error(cookie);
+
+ dma_async_issue_pending(dma_chan);
+
+ return 0;
+}
+
+static int sprd_spi_dma_rx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+ struct dma_chan *dma_chan = ss->dma.dma_chan[SPI_RX];
+ struct dma_slave_config config = {
+ .src_addr = ss->phy_base,
+ .src_addr_width = ss->dma.width,
+ .dst_addr_width = ss->dma.width,
+ .dst_maxburst = ss->dma.fragmens_len,
+ .slave_id = ss->dma.slave_id[SPI_RX],
+ };
+ int ret;
+
+ ret = sprd_spi_dma_submit(dma_chan, &config, &t->rx_sg, DMA_DEV_TO_MEM);
+ if (ret)
+ return ret;
+
+ return ss->dma.rx_len;
+}
+
+static int sprd_spi_dma_tx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+ struct dma_chan *dma_chan = ss->dma.dma_chan[SPI_TX];
+ struct dma_slave_config config = {
+ .dst_addr = ss->phy_base,
+ .src_addr_width = ss->dma.width,
+ .dst_addr_width = ss->dma.width,
+ .src_maxburst = ss->dma.fragmens_len,
+ .slave_id = ss->dma.slave_id[SPI_TX],
+ };
+ int ret;
+
+ ret = sprd_spi_dma_submit(dma_chan, &config, &t->tx_sg, DMA_MEM_TO_DEV);
+ if (ret)
+ return ret;
+
+ return t->len;
+}
+
+static int sprd_spi_dma_request(struct sprd_spi *ss)
+{
+ ss->dma.dma_chan[SPI_RX] = dma_request_chan(ss->dev, "rx_chn");
+ if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPI_RX])) {
+ if (PTR_ERR(ss->dma.dma_chan[SPI_RX]) == -EPROBE_DEFER)
+ return PTR_ERR(ss->dma.dma_chan[SPI_RX]);
+
+ dev_err(ss->dev, "request RX DMA channel failed!\n");
+ return PTR_ERR(ss->dma.dma_chan[SPI_RX]);
+ }
+
+ ss->dma.dma_chan[SPI_TX] = dma_request_chan(ss->dev, "tx_chn");
+ if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPI_TX])) {
+ if (PTR_ERR(ss->dma.dma_chan[SPI_TX]) == -EPROBE_DEFER)
+ return PTR_ERR(ss->dma.dma_chan[SPI_TX]);
+
+ dev_err(ss->dev, "request TX DMA channel failed!\n");
+ dma_release_channel(ss->dma.dma_chan[SPI_RX]);
+ return PTR_ERR(ss->dma.dma_chan[SPI_TX]);
+ }
+
+ return 0;
+}
+
+static void sprd_spi_dma_release(struct sprd_spi *ss)
+{
+ dma_release_channel(ss->dma.dma_chan[SPI_RX]);
+ dma_release_channel(ss->dma.dma_chan[SPI_TX]);
+}
+
+static int sprd_spi_dma_txrx_bufs(struct spi_device *sdev,
+ struct spi_transfer *t)
+{
+ struct sprd_spi *ss = spi_master_get_devdata(sdev->master);
+ u32 trans_len = ss->trans_len;
+ int ret, write_size = 0;
+
+ reinit_completion(&ss->xfer_completion);
+ if (ss->trans_mode & SPRD_SPI_TX_MODE) {
+ write_size = sprd_spi_dma_tx_config(ss, t);
+ sprd_spi_set_tx_length(ss, trans_len);
+
+ /*
+ * For our 3 wires mode or dual TX line mode, we need
+ * to request the controller to transfer.
+ */
+ if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+ sprd_spi_tx_req(ss);
+ } else {
+ sprd_spi_set_rx_length(ss, trans_len);
+
+ /*
+ * For our 3 wires mode or dual TX line mode, we need
+ * to request the controller to read.
+ */
+ if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+ sprd_spi_rx_req(ss);
+ else
+ write_size = ss->write_bufs(ss, trans_len);
+ }
+
+ if (write_size < 0) {
+ ret = write_size;
+ dev_err(ss->dev, "failed to write, ret = %d\n", ret);
+ goto trans_complete;
+ }
+
+ if (ss->trans_mode & SPRD_SPI_RX_MODE) {
+ /*
+ * Set up the DMA receive data length, which must be an
+ * integral multiple of fragment length. But when the length
+ * of received data is less than fragment length, DMA can be
+ * configured to receive data according to the actual length
+ * of received data.
+ */
+ ss->dma.rx_len = t->len > ss->dma.fragmens_len ?
+ (t->len - t->len % ss->dma.fragmens_len) :
+ t->len;
+ ret = sprd_spi_dma_rx_config(ss, t);
+ if (ret < 0) {
+ dev_err(&sdev->dev,
+ "failed to configure rx DMA, ret = %d\n", ret);
+ goto trans_complete;
+ }
+ }
+
+ sprd_spi_dma_enable(ss, true);
+ wait_for_completion(&(ss->xfer_completion));
+
+ if (ss->trans_mode & SPRD_SPI_TX_MODE)
+ ret = write_size;
+ else
+ ret = ss->dma.rx_len;
+
+trans_complete:
+ sprd_spi_dma_enable(ss, false);
+ sprd_spi_enter_idle(ss);
+
+ return ret;
+}
+
static void sprd_spi_set_speed(struct sprd_spi *ss, u32 speed_hz)
{
/*
@@ -488,6 +690,18 @@ static void sprd_spi_init_hw(struct sprd_spi *ss, struct spi_transfer *t)
val &= ~SPRD_SPI_DATA_LINE2_EN;
writel_relaxed(val, ss->base + SPRD_SPI_CTL7);
+
+ if (ss->dma.enable) {
+ /* Clear interrupt status before enabling interrupt. */
+ writel_relaxed(SPRD_SPI_TX_END_CLR | SPRD_SPI_RX_END_CLR,
+ ss->base + SPRD_SPI_INT_CLR);
+
+ /* Enable SPI interrupt only in DMA mode. */
+ val = readl_relaxed(ss->base + SPRD_SPI_INT_EN);
+ writel_relaxed(val | SPRD_SPI_TX_END_INT_EN |
+ SPRD_SPI_RX_END_INT_EN,
+ ss->base + SPRD_SPI_INT_EN);
+ }
}
static int sprd_spi_setup_transfer(struct spi_device *sdev,
@@ -518,16 +732,22 @@ static int sprd_spi_setup_transfer(struct spi_device *sdev,
ss->trans_len = t->len;
ss->read_bufs = sprd_spi_read_bufs_u8;
ss->write_bufs = sprd_spi_write_bufs_u8;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP;
break;
case 16:
ss->trans_len = t->len >> 1;
ss->read_bufs = sprd_spi_read_bufs_u16;
ss->write_bufs = sprd_spi_write_bufs_u16;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 1;
break;
case 32:
ss->trans_len = t->len >> 2;
ss->read_bufs = sprd_spi_read_bufs_u32;
ss->write_bufs = sprd_spi_write_bufs_u32;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 2;
break;
default:
return -EINVAL;
@@ -559,13 +779,18 @@ static int sprd_spi_transfer_one(struct spi_controller *sctlr,
struct spi_device *sdev,
struct spi_transfer *t)
{
+ struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
int ret;
ret = sprd_spi_setup_transfer(sdev, t);
if (ret)
goto setup_err;
- ret = sprd_spi_txrx_bufs(sdev, t);
+ if (ss->dma.enable)
+ ret = sprd_spi_dma_txrx_bufs(sdev, t);
+ else
+ ret = sprd_spi_txrx_bufs(sdev, t);
+
if (ret == t->len)
ret = 0;
else if (ret >= 0)
@@ -591,6 +816,11 @@ static irqreturn_t sprd_spi_handle_irq(int irq, void *data)
if (val & SPRD_SPI_MASK_RX_END) {
writel_relaxed(SPRD_SPI_RX_END_CLR, ss->base + SPRD_SPI_INT_CLR);
+ if (ss->dma.rx_len < ss->len) {
+ ss->rx_buf += ss->dma.rx_len;
+ ss->dma.rx_len +=
+ ss->read_bufs(ss, ss->len - ss->dma.rx_len);
+ }
complete(&ss->xfer_completion);
}
@@ -646,6 +876,43 @@ static int sprd_spi_clk_init(struct platform_device *pdev, struct sprd_spi *ss)
return 0;
}
+static bool sprd_spi_can_dma(struct spi_controller *sctlr,
+ struct spi_device *spi, struct spi_transfer *t)
+{
+ struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
+
+ return ss->dma.enable;
+}
+
+static int sprd_spi_dma_init(struct platform_device *pdev, struct sprd_spi *ss)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ ret = sprd_spi_dma_request(ss);
+ if (ret) {
+ if (ret == -EPROBE_DEFER)
+ return ret;
+
+ dev_warn(&pdev->dev,
+ "failed to request dma, enter no dma mode, ret = %d\n",
+ ret);
+
+ return 0;
+ }
+
+ if (of_property_read_u32_array(np, "sprd,dma-slave-ids",
+ ss->dma.slave_id, SPI_MAX)) {
+ dev_warn(&pdev->dev,
+ "failed to request dma slave id, enter no dma mode\n");
+ return 0;
+ }
+
+ ss->dma.enable = true;
+
+ return 0;
+}
+
static int sprd_spi_probe(struct platform_device *pdev)
{
struct spi_controller *sctlr;
@@ -666,12 +933,14 @@ static int sprd_spi_probe(struct platform_device *pdev)
goto free_controller;
}
+ ss->phy_base = res->start;
ss->dev = &pdev->dev;
sctlr->dev.of_node = pdev->dev.of_node;
sctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_3WIRE | SPI_TX_DUAL;
sctlr->bus_num = pdev->id;
sctlr->set_cs = sprd_spi_chipselect;
sctlr->transfer_one = sprd_spi_transfer_one;
+ sctlr->can_dma = sprd_spi_can_dma;
sctlr->auto_runtime_pm = true;
sctlr->max_speed_hz = min_t(u32, ss->src_clk >> 1,
SPRD_SPI_MAX_SPEED_HZ);
@@ -686,10 +955,14 @@ static int sprd_spi_probe(struct platform_device *pdev)
if (ret)
goto free_controller;
- ret = clk_prepare_enable(ss->clk);
+ ret = sprd_spi_dma_init(pdev, ss);
if (ret)
goto free_controller;
+ ret = clk_prepare_enable(ss->clk);
+ if (ret)
+ goto release_dma;
+
ret = pm_runtime_set_active(&pdev->dev);
if (ret < 0)
goto disable_clk;
@@ -718,6 +991,8 @@ static int sprd_spi_probe(struct platform_device *pdev)
pm_runtime_disable(&pdev->dev);
disable_clk:
clk_disable_unprepare(ss->clk);
+release_dma:
+ sprd_spi_dma_release(ss);
free_controller:
spi_controller_put(sctlr);
@@ -748,6 +1023,9 @@ static int __maybe_unused sprd_spi_runtime_suspend(struct device *dev)
struct spi_controller *sctlr = dev_get_drvdata(dev);
struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
+ if (ss->dma.enable)
+ sprd_spi_dma_release(ss);
+
clk_disable_unprepare(ss->clk);
return 0;
@@ -763,7 +1041,14 @@ static int __maybe_unused sprd_spi_runtime_resume(struct device *dev)
if (ret)
return ret;
- return 0;
+ if (!ss->dma.enable)
+ return 0;
+
+ ret = sprd_spi_dma_request(ss);
+ if (ret)
+ clk_disable_unprepare(ss->clk);
+
+ return ret;
}
static const struct dev_pm_ops sprd_spi_pm_ops = {
--
1.7.9.5
Powered by blists - more mailing lists