linux-kernel - Re: [PATCH v2 2/3] dma: imx-sdma: add clock ratio 1:1 check

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <141a054976519d22aa195affca633c21@www.akkea.ca>
Date:   Mon, 21 Jan 2019 07:43:26 -0700
From:   Angus Ainslie <angus@...ea.ca>
To:     Lucas Stach <l.stach@...gutronix.de>
Cc:     linux-kernel@...r.kernel.org, Vinod Koul <vkoul@...nel.org>,
        NXP Linux Team <linux-imx@....com>,
        Pengutronix Kernel Team <kernel@...gutronix.de>,
        dmaengine@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v2 2/3] dma: imx-sdma: add clock ratio 1:1 check

Hi Lucas,

On 2019-01-21 02:17, Lucas Stach wrote:
> Hi Angus,
> 
> Am Samstag, den 19.01.2019, 19:31 -0700 schrieb Angus Ainslie (Purism):
>> On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted,
>> since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
>> to 500Mhz, so use 1:1 instead.
>> 
>> based on NXP commit MLK-16841-1
>> 
>> > Signed-off-by: Angus Ainslie (Purism) <angus@...ea.ca>
>> ---
>>  .../devicetree/bindings/dma/fsl-imx-sdma.txt  |  1 +
>>  drivers/dma/imx-sdma.c                        | 20 
>> +++++++++++++++----
>>  2 files changed, 17 insertions(+), 4 deletions(-)
>> 
>> diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt 
>> b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
>> index 3c9a57a8443b..17544c1820b7 100644
>> --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
>> +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
>> @@ -67,6 +67,7 @@ Optional properties:
>>      reg is the GPR register offset.
>>      shift is the bit position inside the GPR register.
>>      val is the value of the bit (0 or 1).
>> +- fsl,ratio-1-1: AHB/SDMA core clock ration 1:1, 2:1 without this.
> 
> Why does this need a separate DT property? Shouldn't the driver be able
> to infer this from the clock rates going into the SDMA hardware?
> 

That's probably a better way to do it then setting the property can't
get missed. I'll address it in v3.

Angus

> Regards,
> Lucas
> 
>>  Examples:
>>  
>> diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
>> index 0b3a67ff8e82..65dada21d3c1 100644
>> --- a/drivers/dma/imx-sdma.c
>> +++ b/drivers/dma/imx-sdma.c
>> @@ -440,6 +440,8 @@ struct sdma_engine {
>> > >  	unsigned int			irq;
>> > >  	dma_addr_t			bd0_phys;
>> > >  	struct sdma_buffer_descriptor	*bd0;
>> > +	/* clock ratio for AHB:SDMA core. 1:1 is 1, 2:1 is 0*/
>> > > +	bool				clk_ratio;
>>  };
>>  
>>  static int sdma_config_write(struct dma_chan *chan,
>> @@ -662,8 +664,14 @@ static int sdma_run_channel0(struct sdma_engine 
>> *sdma)
>> >  		dev_err(sdma->dev, "Timeout waiting for CH0 ready\n");
>>  
>> >  	/* Set bits of CONFIG register with dynamic context switching */
>> > -	if (readl(sdma->regs + SDMA_H_CONFIG) == 0)
>> > -		writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG);
>> > +	if (readl(sdma->regs + SDMA_H_CONFIG) == 0) {
>> > +		if (sdma->clk_ratio)
>> > +			reg = SDMA_H_CONFIG_CSM | SDMA_H_CONFIG_ACR;
>> > +		else
>> > +			reg = SDMA_H_CONFIG_CSM;
>> +
>> > +		writel_relaxed(reg, sdma->regs + SDMA_H_CONFIG);
>> > +	}
>>  
>> >  	return ret;
>>  }
>> @@ -1880,8 +1888,10 @@ static int sdma_init(struct sdma_engine *sdma)
>> >  	writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR);
>>  
>> >  	/* Set bits of CONFIG register but with static context switching */
>> > -	/* FIXME: Check whether to set ACR bit depending on clock ratios */
>> > -	writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);
>> > +	if (sdma->clk_ratio)
>> > +		writel_relaxed(SDMA_H_CONFIG_ACR, sdma->regs + SDMA_H_CONFIG);
>> > +	else
>> > +		writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);
>>  
>> >  	writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR);
>>  
>> @@ -1975,6 +1985,8 @@ static int sdma_probe(struct platform_device 
>> *pdev)
>> >  	if (!sdma)
>> >  		return -ENOMEM;
>>  
>> > +	sdma->clk_ratio = of_property_read_bool(np, "fsl,ratio-1-1");
>> +
>> >  	spin_lock_init(&sdma->channel_0_lock);
>>  
>> >  	sdma->dev = &pdev->dev;