| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <f06b0b7b3d86258cda85f545cae69d077e7cc8ca.1548149337.git.matti.vaittinen@fi.rohmeurope.com>
Date: Tue, 22 Jan 2019 11:46:08 +0200
From: Matti Vaittinen <matti.vaittinen@...rohmeurope.com>
To: matti.vaittinen@...rohmeurope.com, mazziesaccount@...il.com
Cc: lee.jones@...aro.org, robh+dt@...nel.org, mark.rutland@....com,
lgirdwood@...il.com, broonie@...nel.org,
gregkh@...uxfoundation.org, rafael@...nel.org,
mturquette@...libre.com, sboyd@...nel.org,
linus.walleij@...aro.org, bgolaszewski@...libre.com,
sre@...nel.org, a.zummo@...ertech.it,
alexandre.belloni@...tlin.com, wim@...ux-watchdog.org,
linux@...ck-us.net, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-clk@...r.kernel.org,
linux-gpio@...r.kernel.org, linux-pm@...r.kernel.org,
linux-rtc@...r.kernel.org, linux-watchdog@...r.kernel.org,
mikko.mutanen@...rohmeurope.com, heikki.haikola@...rohmeurope.com
Subject: [RFC PATCH v1 08/13] regulator: bd70528: Support ROHM BD70528
regulator block
BD70528MWV is an ultra-low Iq general purpose single-chip power
management IC for battery-powered portable devices.
Add support for controlling 3 bucks and 3 LDOs present in
ROHM BD70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@...rohmeurope.com>
---
drivers/regulator/Kconfig | 11 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/bd70528-regulator.c | 290 ++++++++++++++++++++++++++++++++++
3 files changed, 302 insertions(+)
create mode 100644 drivers/regulator/bd70528-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 7fc1f88e27e7..21dc3b59db19 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
BCM590xx PMUs. This will enable support for the software
controllable LDO/Switching regulators.
+config REGULATOR_BD70528
+ tristate "ROHM BD70528 Power Regulator"
+ depends on MFD_ROHM_BD70528
+ help
+ This driver supports voltage regulators on ROHM BD70528 PMIC.
+ This will enable support for the software controllable buck
+ and LDO regulators.
+
+ This driver can also be built as a module. If so, the module
+ will be called bd70528-regulator.
+
config REGULATOR_BD718XX
tristate "ROHM BD71837 Power Regulator"
depends on MFD_ROHM_BD718XX
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index b12e1c9b2118..960406952119 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o
obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
diff --git a/drivers/regulator/bd70528-regulator.c b/drivers/regulator/bd70528-regulator.c
new file mode 100644
index 000000000000..0cf261c469b9
--- /dev/null
+++ b/drivers/regulator/bd70528-regulator.c
@@ -0,0 +1,290 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+// bd70528-regulator.c ROHM BD70528MWV regulator driver
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd70528.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/slab.h>
+
+#define BUCK_RAMPRATE_250MV 0
+#define BUCK_RAMPRATE_125MV 1
+#define BUCK_RAMP_MAX 250
+
+static struct regulator_linear_range bd70528_buck1_volts[] = {
+ REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 600000),
+ REGULATOR_LINEAR_RANGE(2750000, 0x2, 0xf, 50000),
+};
+static struct regulator_linear_range bd70528_buck2_volts[] = {
+ REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 300000),
+ REGULATOR_LINEAR_RANGE(1550000, 0x2, 0xd, 50000),
+ REGULATOR_LINEAR_RANGE(3000000, 0xe, 0xf, 300000),
+};
+static struct regulator_linear_range bd70528_buck3_volts[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0x00, 0xd, 50000),
+ REGULATOR_LINEAR_RANGE(1800000, 0xe, 0xf, 0),
+};
+
+/* All LDOs have same voltage ranges */
+static struct regulator_linear_range bd70528_ldo_volts[] = {
+ REGULATOR_LINEAR_RANGE(1650000, 0x0, 0x07, 50000),
+ REGULATOR_LINEAR_RANGE(2100000, 0x8, 0x0f, 100000),
+ REGULATOR_LINEAR_RANGE(2850000, 0x10, 0x19, 50000),
+ REGULATOR_LINEAR_RANGE(3300000, 0x19, 0x1f, 0),
+};
+
+/* Also both LEDs support same voltages */
+static const unsigned int led_volts[] = {
+ 20000, 30000
+};
+
+static int bd70528_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+ if (ramp_delay > 0 && ramp_delay <= BUCK_RAMP_MAX) {
+ unsigned int ramp_value = BUCK_RAMPRATE_250MV;
+
+ if (ramp_delay <= 125)
+ ramp_value = BUCK_RAMPRATE_125MV;
+
+ return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+ BD70528_MASK_BUCK_RAMP,
+ ramp_value << BD70528_SIFT_BUCK_RAMP);
+ }
+ dev_err(&rdev->dev, "%s: ramp_delay: %d not supported\n",
+ rdev->desc->name, ramp_delay);
+ return -EINVAL;
+}
+
+static int bd70528_led_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ int ret;
+
+ ret = regulator_is_enabled_regmap(rdev);
+ if (ret < 0)
+ return ret;
+
+ if (ret == 0)
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+
+ dev_err(&rdev->dev,
+ "LED voltage change not allowed when led is enabled\n");
+
+ return -EBUSY;
+}
+
+static struct regulator_ops bd70528_buck_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = bd70528_set_ramp_delay,
+};
+
+static struct regulator_ops bd70528_ldo_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = bd70528_set_ramp_delay,
+};
+
+static struct regulator_ops bd70528_led_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = bd70528_led_set_voltage_sel,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+
+static struct regulator_desc bd70528_desc[] = {
+ {
+ .name = "buck1",
+ .of_match = of_match_ptr("BUCK1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_BUCK1,
+ .ops = &bd70528_buck_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_buck1_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_buck1_volts),
+ .n_voltages = BD70528_BUCK_VOLTS,
+ .enable_reg = BD70528_REG_BUCK1_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_BUCK1_VOLT,
+ .vsel_mask = BD70528_MASK_BUCK_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck2",
+ .of_match = of_match_ptr("BUCK2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_BUCK2,
+ .ops = &bd70528_buck_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_buck2_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_buck2_volts),
+ .n_voltages = BD70528_BUCK_VOLTS,
+ .enable_reg = BD70528_REG_BUCK2_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_BUCK2_VOLT,
+ .vsel_mask = BD70528_MASK_BUCK_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck3",
+ .of_match = of_match_ptr("BUCK3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_BUCK3,
+ .ops = &bd70528_buck_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_buck3_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_buck3_volts),
+ .n_voltages = BD70528_BUCK_VOLTS,
+ .enable_reg = BD70528_REG_BUCK3_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_BUCK3_VOLT,
+ .vsel_mask = BD70528_MASK_BUCK_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo1",
+ .of_match = of_match_ptr("LDO1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_LDO1,
+ .ops = &bd70528_ldo_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_ldo_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+ .n_voltages = BD70528_LDO_VOLTS,
+ .enable_reg = BD70528_REG_LDO1_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_LDO1_VOLT,
+ .vsel_mask = BD70528_MASK_LDO_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo2",
+ .of_match = of_match_ptr("LDO2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_LDO2,
+ .ops = &bd70528_ldo_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_ldo_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+ .n_voltages = BD70528_LDO_VOLTS,
+ .enable_reg = BD70528_REG_LDO2_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_LDO2_VOLT,
+ .vsel_mask = BD70528_MASK_LDO_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo3",
+ .of_match = of_match_ptr("LDO3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_LDO3,
+ .ops = &bd70528_ldo_ops,
+ .type = REGULATOR_VOLTAGE,
+ .linear_ranges = bd70528_ldo_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+ .n_voltages = BD70528_LDO_VOLTS,
+ .enable_reg = BD70528_REG_LDO3_EN,
+ .enable_mask = BD70528_MASK_RUN_EN,
+ .vsel_reg = BD70528_REG_LDO3_VOLT,
+ .vsel_mask = BD70528_MASK_LDO_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo_led1",
+ .of_match = of_match_ptr("LDO_LED1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_LED1,
+ .ops = &bd70528_led_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &led_volts[0],
+ .n_voltages = ARRAY_SIZE(led_volts),
+ .enable_reg = BD70528_REG_LED_EN,
+ .enable_mask = BD70528_MASK_LED1_EN,
+ .vsel_reg = BD70528_REG_LED_VOLT,
+ .vsel_mask = BD70528_MASK_LED1_VOLT,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo_led2",
+ .of_match = of_match_ptr("LDO_LED2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD70528_LED2,
+ .ops = &bd70528_led_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &led_volts[0],
+ .n_voltages = ARRAY_SIZE(led_volts),
+ .enable_reg = BD70528_REG_LED_EN,
+ .enable_mask = BD70528_MASK_LED2_EN,
+ .vsel_reg = BD70528_REG_LED_VOLT,
+ .vsel_mask = BD70528_MASK_LED2_VOLT,
+ .owner = THIS_MODULE,
+ },
+
+};
+
+static int bd70528_probe(struct platform_device *pdev)
+{
+ struct bd70528 *bd70528;
+ int i;
+ struct regulator_config config = {
+ .dev = pdev->dev.parent,
+ };
+
+ bd70528 = dev_get_drvdata(pdev->dev.parent);
+ if (!bd70528) {
+ dev_err(&pdev->dev, "No MFD driver data\n");
+ return -EINVAL;
+ }
+
+ config.regmap = bd70528->chip.regmap;
+
+ for (i = 0; i < ARRAY_SIZE(bd70528_desc); i++) {
+ struct regulator_dev *rdev;
+
+ rdev = devm_regulator_register(&pdev->dev, &bd70528_desc[i],
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev,
+ "failed to register %s regulator\n",
+ bd70528_desc[i].name);
+ return PTR_ERR(rdev);
+ }
+ }
+ return 0;
+}
+
+static struct platform_driver bd70528_regulator = {
+ .driver = {
+ .name = "bd70528-pmic"
+ },
+ .probe = bd70528_probe,
+};
+
+module_platform_driver(bd70528_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@...rohmeurope.com>");
+MODULE_DESCRIPTION("BD70528 voltage regulator driver");
+MODULE_LICENSE("GPL");
--
2.14.3
--
Matti Vaittinen
ROHM Semiconductors
~~~ "I don't think so," said Rene Descartes. Just then, he vanished ~~~
Powered by blists - more mailing lists