| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190125095507.29334-1-miquel.raynal@bootlin.com>
Date: Fri, 25 Jan 2019 10:55:05 +0100
From: Miquel Raynal <miquel.raynal@...tlin.com>
To: Andrew Lunn <andrew@...n.ch>,
Vivien Didelot <vivien.didelot@...il.com>,
Florian Fainelli <f.fainelli@...il.com>,
"David S. Miller" <davem@...emloft.net>
Cc: netdev@...r.kernel.org, <linux-kernel@...r.kernel.org>,
Thomas Petazzoni <thomas.petazzoni@...tlin.com>,
Gregory Clement <gregory.clement@...tlin.com>,
Antoine Tenart <antoine.tenart@...tlin.com>,
Maxime Chevallier <maxime.chevallier@...tlin.com>,
Nadav Haklai <nadavh@...vell.com>,
Miquel Raynal <miquel.raynal@...tlin.com>
Subject: [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support
After a first attempt of bringing S2RAM support to the DSA switch, it
has been reported that a part of the configuration was lost during the
cycle. This second version adds a first patch that saves the rules in
a per-chip list when they are applied, so that in the second patch we
bring S2RAM support by also re-applying these rules.
Bridging is set up on the EspressoBin with the below commands (thanks
to Andrew):
ip link set eth0 up
ip link add name br0 type bridge
ip link set br0 up
ip link set lan0 up
ip link set lan0 master br0
ip link set lan1 up
ip link set lan1 master br0
Static forwarding entries are added:
bridge fdb add 00:42:42:42:42:42 dev lan0
bridge fdb add 00:24:24:24:24:24 dev lan1
Dumping the switch entries gives:
# bridge fdb show
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:06:e2:95 dev eth0 self permanent
dc:0b:34:87:7f:27 dev lan0 br0
d4:81:d7:4f:a1:0d dev lan0 br0
f0:ad:4e:06:e2:95 dev lan0 vlan 1 br0 permanent
f0:ad:4e:06:e2:95 dev lan0 br0 permanent
00:42:42:42:42:42 dev lan0 self static
d4:81:d7:4f:a1:0d dev lan0 self
dc:0b:34:87:7f:27 dev lan0 self
00:0a:35:00:01:22 dev lan1 br0
00:0a:35:00:01:22 dev lan1 self
00:24:24:24:24:24 dev lan1 self static
33:33:00:00:00:01 dev br0 self permanent
01:00:5e:00:00:01 dev br0 self permanent
33:33:ff:00:2a:68 dev br0 self permanent
After a S2RAM cycle, the bridge and the static entries have been restored.
mv88e6085 d0032004.mdio-mii:01 lan0: configuring for phy/ link mode
mv88e6085 d0032004.mdio-mii:01 lan1: configuring for phy/ link mode
mv88e6085 d0032004.mdio-mii:01 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
mv88e6085 d0032004.mdio-mii:01 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
# bridge fdb show
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:06:e2:95 dev eth0 self permanent
9c:93:4e:26:e4:54 dev lan0 br0
d4:81:d7:45:de:60 dev lan0 br0
dc:0b:34:87:7f:27 dev lan0 br0
d4:81:d7:4f:a1:0d dev lan0 br0
f0:ad:4e:06:e2:95 dev lan0 vlan 1 br0 permanent
f0:ad:4e:06:e2:95 dev lan0 br0 permanent
00:42:42:42:42:42 dev lan0 self static
d4:81:d7:4f:a1:0d dev lan0 self
00:0a:35:00:01:22 dev lan1 br0
00:0a:35:00:01:22 dev lan1 self
00:24:24:24:24:24 dev lan1 self static
33:33:00:00:00:01 dev br0 self permanent
01:00:5e:00:00:01 dev br0 self permanent
33:33:ff:00:2a:68 dev br0 self permanent
An iperf test running over the whole cycle gives:
1.00-2.00 sec 81.7 MBytes 685 Mbits/sec
2.00-3.00 sec 81.8 MBytes 687 Mbits/sec
3.00-4.00 sec 81.8 MBytes 685 Mbits/sec
4.00-5.00 sec 81.7 MBytes 686 Mbits/sec
5.00-6.00 sec 81.5 MBytes 683 Mbits/sec
6.00-7.00 sec 81.6 MBytes 685 Mbits/sec
7.00-8.00 sec 81.5 MBytes 684 Mbits/sec
8.00-9.00 sec 81.7 MBytes 685 Mbits/sec
9.00-10.00 sec 81.5 MBytes 684 Mbits/sec
10.00-11.00 sec 81.6 MBytes 684 Mbits/sec
11.00-12.00 sec 81.5 MBytes 683 Mbits/sec
macb e000b000.ethernet eth0: link down
12.00-13.00 sec 19.5 MBytes 164 Mbits/sec
13.00-14.00 sec 0.00 Bytes 0.00 bits/sec
14.00-15.00 sec 0.00 Bytes 0.00 bits/sec
15.00-16.00 sec 0.00 Bytes 0.00 bits/sec
16.00-17.00 sec 0.00 Bytes 0.00 bits/sec
17.00-18.00 sec 0.00 Bytes 0.00 bits/sec
18.00-19.00 sec 0.00 Bytes 0.00 bits/sec
19.00-20.00 sec 0.00 Bytes 0.00 bits/sec
20.00-21.00 sec 0.00 Bytes 0.00 bits/sec
21.00-22.00 sec 0.00 Bytes 0.00 bits/sec
22.00-23.00 sec 0.00 Bytes 0.00 bits/sec
macb e000b000.ethernet eth0: link up (1000/Full)
23.00-24.00 sec 0.00 Bytes 0.00 bits/sec
24.00-25.00 sec 0.00 Bytes 0.00 bits/sec
25.00-26.00 sec 18.6 MBytes 156 Mbits/sec
26.00-27.00 sec 81.5 MBytes 684 Mbits/sec
27.00-28.00 sec 81.6 MBytes 684 Mbits/sec
28.00-29.00 sec 81.5 MBytes 684 Mbits/sec
29.00-30.00 sec 81.5 MBytes 683 Mbits/sec
30.00-31.00 sec 81.6 MBytes 685 Mbits/sec
31.00-32.00 sec 81.6 MBytes 684 Mbits/sec
32.00-33.00 sec 81.4 MBytes 683 Mbits/sec
33.00-34.00 sec 81.4 MBytes 683 Mbits/sec
33.00-34.00 sec 81.4 MBytes 683 Mbits/sec
I hope everything has been restored correctly, please let me know if
you spot anything else that is missing.
Thanks,
Miquèl
Miquel Raynal (2):
net: dsa: mv88e6xxx: Save switch rules
net: dsa: mv88e6xxx: Add suspend to RAM support
drivers/net/dsa/mv88e6xxx/chip.c | 359 ++++++++++++++++++++++++++++---
drivers/net/dsa/mv88e6xxx/chip.h | 33 +++
2 files changed, 357 insertions(+), 35 deletions(-)
--
2.19.1
Powered by blists - more mailing lists