| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAJKOXPe5EFpcwzmpNfjcjfW0zkDo5TOFy7wSk9YH8bymHyA5FQ@mail.gmail.com>
Date: Tue, 29 Jan 2019 16:03:20 +0100
From: Krzysztof Kozlowski <krzk@...nel.org>
To: Lukasz Luba <l.luba@...tner.samsung.com>
Cc: devicetree@...r.kernel.org,
Bartłomiej Żołnierkiewicz
<b.zolnierkie@...sung.com>, myungjoo.ham@...sung.com,
Kyungmin Park <kyungmin.park@...sung.com>,
Chanwoo Choi <cw00.choi@...sung.com>,
Kukjin Kim <kgene@...nel.org>, linux-kernel@...r.kernel.org,
linux-pm@...r.kernel.org,
"linux-samsung-soc@...r.kernel.org"
<linux-samsung-soc@...r.kernel.org>,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 5/8] drivers: devfreq: exynos5: add DMC driver
On Mon, 28 Jan 2019 at 20:21, Lukasz Luba <l.luba@...tner.samsung.com> wrote:
>
> This patch adds driver for Exynos5422 Dynamic Memory Controller.
> The driver provides support for Dynamic Frequency and Voltage scaling for
> DMC and DRAM. It supports changing timings of DRAM running with different
> frequency.
> The patch also contains needed MAINTAINERS file update.
>
> CC: MyungJoo Ham <myungjoo.ham@...sung.com>
> CC: Kyungmin Park <kyungmin.park@...sung.com>
> CC: Chanwoo Choi <cw00.choi@...sung.com>
> CC: Kukjin Kim <kgene@...nel.org>
> CC: Krzysztof Kozlowski <krzk@...nel.org>
> CC: linux-kernel@...r.kernel.org
> CC: linux-pm@...r.kernel.org
> CC: linux-samsung-soc@...r.kernel.org
> CC: linux-arm-kernel@...ts.infradead.org
> Signed-off-by: Lukasz Luba <l.luba@...tner.samsung.com>
> ---
> MAINTAINERS | 1 +
> drivers/devfreq/Kconfig | 13 +
> drivers/devfreq/Makefile | 1 +
> drivers/devfreq/exynos5-dmc.c | 1335 +++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 1350 insertions(+)
> create mode 100644 drivers/devfreq/exynos5-dmc.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3581807..9dcf289 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3315,6 +3315,7 @@ M: Lukasz Luba <l.luba@...tner.samsung.com>
> L: linux-pm@...r.kernel.org
> L: linux-samsung-soc@...r.kernel.org
> S: Maintained
> +F: drivers/devfreq/exynos5-dmc.c
> F: Documentation/devicetree/bindings/devfreq/exynos5-dmc.txt
>
> BUSLOGIC SCSI DRIVER
> diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
> index 6a172d3..5058391 100644
> --- a/drivers/devfreq/Kconfig
> +++ b/drivers/devfreq/Kconfig
> @@ -113,6 +113,19 @@ config ARM_RK3399_DMC_DEVFREQ
> It sets the frequency for the memory controller and reads the usage counts
> from hardware.
>
> +config ARM_EXYNOS_DMC_DEVFREQ
> + tristate "ARM EXYNOS DMC DEVFREQ Driver"
> + depends on ARCH_EXYNOS || COMPILE_TEST
> + select DEVFREQ_GOV_SIMPLE_ONDEMAND
> + select DEVFREQ_GOV_PASSIVE
> + select PM_DEVFREQ_EVENT
> + select PM_OPP
> + help
> + This adds DEVFREQ driver for Exynos5 DMC (Dynamic Memory Controller).
> + The driver provides support for Dynamic Voltage and Frequency Scaling in
> + DMC and DRAM. It also supports changing timings of DRAM running with
> + different frequency.
> +
> source "drivers/devfreq/event/Kconfig"
>
> endif # PM_DEVFREQ
> diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
> index 32b8d4d..61b535a 100644
> --- a/drivers/devfreq/Makefile
> +++ b/drivers/devfreq/Makefile
> @@ -11,6 +11,7 @@ obj-$(CONFIG_DEVFREQ_GOV_PASSIVE) += governor_passive.o
> obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ) += exynos-bus.o
> obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) += rk3399_dmc.o
> obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra-devfreq.o
> +obj-$(CONFIG_ARM_EXYNOS_DMC_DEVFREQ) += exynos5-dmc.o
>
> # DEVFREQ Event Drivers
> obj-$(CONFIG_PM_DEVFREQ_EVENT) += event/
> diff --git a/drivers/devfreq/exynos5-dmc.c b/drivers/devfreq/exynos5-dmc.c
> new file mode 100644
> index 0000000..0d86a06
> --- /dev/null
> +++ b/drivers/devfreq/exynos5-dmc.c
> @@ -0,0 +1,1335 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019, Samsung
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/devfreq.h>
> +#include <linux/devfreq-event.h>
> +#include <linux/device.h>
> +#include <linux/export.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/pm_opp.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +
> +#define DRIVER_DESC "Driver for Exynos5 Dynamic Memory Controller dynamic frequency and voltage change"
> +
> +#define EXYNOS5422_REV_0 (0x1)
> +#define EXYNOS5422_PROD_REV_MAIN_MASK (0xf0)
> +#define EXYNOS5422_PROD_REV_SUB_MASK (0xf)
> +
> +#define EXYNOS5_DREXI_TIMINGAREF (0x0030)
> +#define EXYNOS5_DREXI_TIMINGROW0 (0x0034)
> +#define EXYNOS5_DREXI_TIMINGDATA0 (0x0038)
> +#define EXYNOS5_DREXI_TIMINGPOWER0 (0x003C)
> +#define EXYNOS5_DREXI_TIMINGROW1 (0x00E4)
> +#define EXYNOS5_DREXI_TIMINGDATA1 (0x00E8)
> +#define EXYNOS5_DREXI_TIMINGPOWER1 (0x00EC)
> +
> +#define EXYNOS5_DREXI_MEMCTRL (0x0004)
> +#define EXYNOS5_DREXI_DIRECTCMD (0x0010)
> +#define EXYNOS5_DREXI_TIMINGAREF (0x0030)
> +#define EXYNOS5_DREXI_TIMINGSETSW (0x00E0)
> +#define EXYNOS5_DREXI_MRSTATUS (0x0054)
> +#define EXYNOS5_DREXI_QOSCONTROL8 (0x00A0)
> +#define EXYNOS5_DREXI_BRBRSVCONTROL (0x0100)
> +#define EXYNOS5_DREXI_BP_CONTROL0 (0x0210)
> +#define EXYNOS5_DREXI_BP_CONTROL1 (0x0220)
> +#define EXYNOS5_DREXI_BP_CONTROL2 (0x0230)
> +#define EXYNOS5_DREXI_BP_CONTROL3 (0x0240)
> +
> +#define EXYNOS5_LPDDR3PHY_CON3 (0x0A20)
> +#define EXYNOS5_TIMING_SET_SWI (1UL << 28)
> +
> +#define AREF_NORMAL (0x2e)
> +
> +#define EXYNOS5_TIMING_USE_SET (1UL << 4)
> +#define EXYNOS5_TIMING_SET_SW_CON (1UL)
> +
> +#define EXYNOS5_CLK_MUX_STAT_CDREX (0x400)
> +#define EXYNOS5_MCLK_CDREX_SEL_BPLL (1UL)
> +#define EXYNOS5_MCLK_CDREX_SEL_MX_MSPLL (2UL)
> +#define EXYNOS5_CLKSRC_CDREX_SEL_SHIFT (4)
> +#define EXYNOS5_MCLK_CDREX_MASK (0x7)
> +
> +#define EXYNOS5_CLK_SRC_CDREX (0x200)
> +#define DMC_PAUSE_CTRL (0x91C)
> +#define DMC_PAUSE_ENABLE (1UL)
> +#define SELF_REFRESH_MASK (0x20UL)
> +#define SR_CMD_EXIT_CHIP0 (0x08000000)
> +#define SR_CMD_EXIT_CHIP1 (0x08100000)
> +#define CMD_SR_ENTER (0x04000000)
> +#define CMD_SR_EXIT (0x08000000)
> +#define CMD_CHIP0 (0x00000000)
> +#define CMD_CHIP1 (0x00100000)
> +#define USE_MX_MSPLL_TIMINGS (1)
> +#define USE_BPLL_TIMINGS (0)
> +
> +#define DMC_REG_VOLT_STEP 0
> +
> +#define IS_MEM_2GB(val) \
> + ( \
> + (((val) & 0xf0) & 0x20) ? 1 : \
> + (((val) & 0xf0) & 0x30) ? 1 : 0 \
> + )
> +
> +#define EXYNOS5_POP_OPTIONS(val) \
> + (((val >> 4) & 0x3UL) << 4)
> +#define EXYNOS5_DDR_TYPE(val) \
> + (((val >> 14) & 0x1UL))
> +
> +#define CHIP_PROD_ID (0)
> +#define CHIP_PKG_ID (4)
> +
> +#define PMCNT_CONST_RATIO_MUL 15
> +#define PMCNT_CONST_RATIO_DIV 10
> +
> +/**
> + * enum dmc_slot_id - An enum with slots in DMC
> + */
> +enum dmc_slot_id {
> + DMC0_0,
> + DMC0_1,
> + DMC1_0,
> + DMC1_1,
> + DMC_SLOTS_END
> +};
> +
> +/**
> + * struct dmc_slot_info - Describes DMC's slot
> + *
> + * The structure holds DMC's slot name which is part of the device name
> + * provided in DT. Each slot has particular share of the DMC bandwidth.
> + * To abstract the model performance and values in performance counters,
> + * fields 'ratio_mul' and 'ratio_div' are used in calculation algorithm
> + * for each slot. Please check the corresponding function with the algorithm,
> + * to see how these variables are used.
> + */
> +struct dmc_slot_info {
> + char *name;
> + int id;
> + int ratio_mul;
> + int ratio_div;
> +};
> +
> +/**
> + * struct dmc_opp_table - Operating level desciption
> + *
> + * Covers frequency and voltage settings of the DMC operating mode.
> + */
> +struct dmc_opp_table {
> + unsigned long freq_khz;
> + unsigned long volt_uv;
> +};
> +
> +/**
> + * struct dram_param - Parameters for the external memory chip
> + *
> + * Covers timings settings for a particular memory chip's operating frequency.
> + */
> +struct dram_param {
> + unsigned int timing_row;
> + unsigned int timing_data;
> + unsigned int timing_power;
> +};
> +
> +/**
> + * struct exynos5_dmc - main structure describing DMC device
> + *
> + * The main structure for the Dynamic Memory Controller which covers clocks,
> + * memory regions, HW information, parameters and current operating mode.
> + */
> +struct exynos5_dmc {
> + struct device *dev;
> + struct devfreq *df;
> + struct devfreq_simple_ondemand_data gov_data;
> + void __iomem *base_drexi0;
> + void __iomem *base_drexi1;
> + void __iomem *base_clk;
> + void __iomem *chip_id;
> + struct mutex lock;
> + unsigned long curr_rate;
> + unsigned long curr_volt;
> + const struct dmc_opp_table *opp;
> + const struct dmc_opp_table *opp_bypass;
> + int opp_count;
> + const struct dram_param *dram_param;
> + const struct dram_param *dram_bypass_param;
> + int dram_param_count;
> + unsigned int prod_rev;
> + unsigned int pkg_rev;
> + unsigned int mem_info;
> + struct regulator *vdd_mif;
> + struct clk *fout_spll;
> + struct clk *fout_bpll;
> + struct clk *mout_spll;
> + struct clk *mout_bpll;
> + struct clk *mout_mclk_cdrex;
> + struct clk *dout_clk2x_phy0;
> + struct clk *mout_mx_mspll_ccore;
> + struct clk *mx_mspll_ccore_phy;
> + struct clk *mout_mx_mspll_ccore_phy;
> + struct devfreq_event_dev **counter;
> + int num_counters;
> + bool counters_enabled;
> +};
> +
> +/**
> + * exynos5_counters_fname() - Macro generating function for event devices
> + * @f: function name suffix
> + *
> + * Macro which generates needed function for manipulation of event devices.
> + * It aims to avoid code duplication relaying on similar prefix and function
> + * parameters in the devfreq event device framework functions.
> + */
> +#define exynos5_counters_fname(f) \
> +static int exynos5_counters_##f(struct exynos5_dmc *dmc) \
> +{ \
> + int i, ret; \
> + \
> + for (i = 0; i < dmc->num_counters; i++) { \
> + if (!dmc->counter[i]) \
> + continue; \
> + ret = devfreq_event_##f(dmc->counter[i]); \
> + if (ret < 0) \
> + return ret; \
> + } \
> + return 0; \
> +}
> +exynos5_counters_fname(set_event);
> +exynos5_counters_fname(enable_edev);
> +exynos5_counters_fname(disable_edev);
> +
> +/**
> + * dmc_opp_exynos5422 - Array with frequency and voltage values
> + *
> + * Operating points for Exynos5422 SoC revisions.
> + * The order and sizeof the array has a meaning and is tightly connected with
> + * DRAM parameters in arrays bellow.
> + */
> +static const struct dmc_opp_table dmc_opp_exynos5422[] = {
> + {825000, 1050000},
> + {728000, 1037500},
> + {633000, 1012500},
> + {543000, 937500},
> + {413000, 887500},
> + {275000, 875000},
> + {206000, 875000},
> + {165000, 875000},
This should be OPP from DTS. Certain flavors of Exynos542x might differ.
> +};
> +
> +/**
> + * dmc_opp_bypass_exynos5422 - frequency and voltage level for temporary mode
> + */
> +static const struct dmc_opp_table dmc_opp_bypass_exynos5422 = {400000, 887500};
> +
> +/**
> + * dram_param_exynos5422 - DRAM timings for particular HW setup
> + *
> + * Operating parameters for DRAM memory running with different clock frequency.
> + * The order is the same as in 'dmc_opp_table' above, the highest frequency
> + * is first.
> + * These settings are needed for proper operation of the DRAM memory with
> + * corresponding frequency. They are calculated for Exynos5422 revision 0
> + * with 2GB LPDDR3 memory chip.
> + */
> +static const struct dram_param dram_param_exynos5422[] = {
> + {0x365A9713, 0x4740085E, 0x543A0446},
> + {0x30598651, 0x3730085E, 0x4C330336},
> + {0x2A48758F, 0x3730085E, 0x402D0335},
> + {0x244764CD, 0x3730085E, 0x38270335},
> + {0x1B35538A, 0x2720085E, 0x2C1D0225},
> + {0x12244287, 0x2720085E, 0x1C140225},
> + {0x112331C6, 0x2720085E, 0x180F0225},
> + {0x11223185, 0x2720085E, 0x140C0225},
> +};
> +
> +
> +/**
> + * Operating parameters for DRAM memory running on temporary clock 400MHz during
> + * switching frequency on the main clock. This variable provides timings for
> + * Exynos5422 SoC revision 0 and DRAM 2GB chip.
> + */
> +static const struct dram_param dram_bypass_param_exynos5422 = {
> + 0x365a9713, 0x4740085e, 0x543a0446
> +};
> +
> +/**
> + * dmc_slot - An array which holds DMC's slots information
> + *
> + * The array is used in algorithm calculating slots performance and usage
> + * based on performance counters' values. The values i.e. 15/10=1.5 correspond
> + * to slot share in the DMC channel, which has 2.0 abstract width.
> + */
> +static const struct dmc_slot_info dmc_slot[] = {
> + {"dmc0_0", DMC0_0, 15, 10},
> + {"dmc0_1", DMC0_1, 5, 10},
> + {"dmc1_0", DMC1_0, 10, 10},
> + {"dmc1_1", DMC1_0, 10, 10},
> +};
> +
> +static const char rev[] = "DMC on SoC rev. prod id 0x%08x, pkg id 0x%08x\n";
Why do you need this? How is it used?
> +
> +/**
> + * revision_show() - Shows revision information of the DMC device
> + * @dev: device for which the information is going to be shown
> + * @attr: file attributes from the sysfs
> + * @buf: destination buffer provided by sysfs
> + *
> + * Simple function providing information about DMC HW revision
> + */
> +static ssize_t revision_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + ssize_t res = 0;
> + struct exynos5_dmc *dmc = dev_get_drvdata(dev->parent);
> + int rev_len = sizeof(rev) + 10;
> +
> + res += snprintf(&buf[res], rev_len, rev, dmc->prod_rev, dmc->pkg_rev);
> + return res;
> +}
> +
> +static DEVICE_ATTR_RO(revision);
> +
> +static struct attribute *env_attributes[] = {
> + &dev_attr_revision.attr,
> + NULL
> +};
> +
> +static struct attribute_group env_group = {
> + .name = "dmc_info",
> + .attrs = env_attributes,
> +};
> +
> +/**
> + * find_target_freq_id() - Finds requested frequency in local DMC configuration
> + * @dmc: device for which the information is checked
> + * @target_rate: requested frequency in KHz
> + *
> + * Seeks in the local DMC driver structure for the requested frequency value
> + * and returns index or error value.
> + */
> +static int find_target_freq_idx(struct exynos5_dmc *dmc,
> + unsigned long target_rate)
> +{
> + int i;
> +
> + for (i = 0; i < dmc->opp_count; i++)
> + if (dmc->opp[i].freq_khz <= target_rate)
> + return i;
> +
> + return -EINVAL;
> +}
> +
> +/**
> + * exynos5_get_chip_info() - Gets chip ID information
Wrong name of function.
> + * @dmc: device for which the information is checked
> + *
> + * Function wrapper for getting the chip ID information.
> + */
> +static void exynos5_read_chip_info(struct exynos5_dmc *dmc)
> +{
> + unsigned int val;
> +
> + val = readl(dmc->chip_id + CHIP_PROD_ID);
> + dmc->prod_rev = val;
> +
> + val = readl(dmc->chip_id + CHIP_PKG_ID);
> + dmc->pkg_rev = val;
> +
> + dmc->mem_info = EXYNOS5_POP_OPTIONS(val);
> + dmc->mem_info |= EXYNOS5_DDR_TYPE(val);
> +}
> +
> +/**
> + * exynos5_get_chip_info() - Gets chip ID information
> + * @dmc: device for which the information is checked
> + *
> + * Function wrapper for getting the chip ID information.
> + */
> +static int exynos5_get_chip_info(struct exynos5_dmc *dmc)
> +{
> + exynos5_read_chip_info(dmc);
> +
> + dev_info(dmc->dev, "memory type %#x\n", dmc->mem_info);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_pause_on_switching() - Controls a pause feature in DMC
> + * @dmc: device which is used for changing this feature
> + * @set: a boolean state passing enable/disable request
> + *
> + * There is a need of pausing DREX DMC when divider or MUX in clock tree
> + * changes its configuration. In such situation access to the memory is blocked
> + * in DMC automatically. This feature is used when clock frequency change
> + * request appears and touches clock tree.
> + */
> +static int exynos5_dmc_pause_on_switching(struct exynos5_dmc *dmc, bool set)
> +{
> + unsigned int val;
> +
> + val = readl(dmc->base_clk + DMC_PAUSE_CTRL);
> + if (set)
> + val |= DMC_PAUSE_ENABLE;
> + else
> + val &= ~DMC_PAUSE_ENABLE;
> + writel(val, dmc->base_clk + DMC_PAUSE_CTRL);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_chip_revision_settings() - Chooses proper DMC's configuration
> + * @dmc: device for which is going to be checked and configured
> + *
> + * Function checks the HW product information in order to choose proper
> + * configuration for DMC frequency, voltage and DRAM timings.
> + */
> +static int exynos5_dmc_chip_revision_settings(struct exynos5_dmc *dmc)
> +{
> + int res;
> +
> + res = exynos5_get_chip_info(dmc);
> + if (res)
> + return res;
> +
> + if (!IS_MEM_2GB(dmc->mem_info)) {
> + dev_warn(dmc->dev, "DRAM memory type not supported\n");
> + return -EINVAL;
> + }
> +
> + dmc->dram_param = dram_param_exynos5422;
> +
> + dmc->dram_param_count = ARRAY_SIZE(dram_param_exynos5422);
> +
> + dmc->dram_bypass_param = &dram_bypass_param_exynos5422;
> +
> + dmc->opp = dmc_opp_exynos5422;
> + dmc->opp_count = ARRAY_SIZE(dmc_opp_exynos5422);
> +
> + dmc->opp_bypass = &dmc_opp_bypass_exynos5422;
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_init_freq_table() - Initialized PM OPP framework
> + * @dev: devfreq device for which the OPP table is going to be
> + * initialized
> + * @dmc: DMC device for which the frequencies are used for OPP init
> + * @profile: devfreq device's profile
> + *
> + * Populate the devfreq device's OPP table based on current frequency, voltage.
> + */
> +static int exynos5_init_freq_table(struct device *dev, struct exynos5_dmc *dmc,
> + struct devfreq_dev_profile *profile)
> +{
> + int i, ret;
> +
> + for (i = 0; i < dmc->opp_count; i++) {
> + ret = dev_pm_opp_add(dev, dmc->opp[i].freq_khz,
> + dmc->opp[i].volt_uv);
> + if (ret) {
> + dev_warn(dev, "failed to add opp %uHz %umV\n", 1, 1);
> + while (i-- > 0)
> + dev_pm_opp_remove(dev, dmc->opp[i].freq_khz);
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_set_bypass_dram_timings() - Low-level changes of the DRAM timings
> + * @dmc: device for which the new settings is going to be applied
> + * @param: DRAM parameters which passes timing data
> + *
> + * Low-level function for changing timings for DRAM memory clocking from
> + * 'bypass' clock source (fixed frequency @400MHz).
> + * It uses timing bank registers set 1.
> + */
> +static void exynos5_set_bypass_dram_timings(struct exynos5_dmc *dmc,
> + const struct dram_param *param)
> +{
> +
> + writel(AREF_NORMAL, dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGAREF);
> +
> + writel(param->timing_row,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGROW1);
> + writel(param->timing_row,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGROW1);
> + writel(param->timing_data,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGDATA1);
> + writel(param->timing_data,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGDATA1);
> + writel(param->timing_power,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGPOWER1);
> + writel(param->timing_power,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGPOWER1);
> +}
> +
> +
> +/**
> + * exynos5_dram_change_timings() - Low-level changes of the DRAM final timings
> + * @dmc: device for which the new settings is going to be applied
> + * @target_rate: target frequency of the DMC
> + *
> + * Low-level function for changing timings for DRAM memory operating from main
> + * clock source (BPLL), which can have different frequencies. Thus, each
> + * frequency must have corresponding timings register values in order to keep
> + * the needed delays.
> + * It uses timing bank registers set 0.
> + */
> +static int exynos5_dram_change_timings(struct exynos5_dmc *dmc,
> + unsigned long target_rate)
> +{
> + int idx;
> +
> +
> + for (idx = 0; idx < dmc->dram_param_count; idx++)
> + if (dmc->opp[idx].freq_khz <= target_rate)
> + break;
> +
> + if (idx >= dmc->dram_param_count)
> + return -EINVAL;
> +
> + writel(AREF_NORMAL, dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGAREF);
> +
> + writel(dmc->dram_param[idx].timing_row,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGROW0);
> + writel(dmc->dram_param[idx].timing_row,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGROW0);
> + writel(dmc->dram_param[idx].timing_data,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGDATA0);
> + writel(dmc->dram_param[idx].timing_data,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGDATA0);
> + writel(dmc->dram_param[idx].timing_power,
> + dmc->base_drexi0 + EXYNOS5_DREXI_TIMINGPOWER0);
> + writel(dmc->dram_param[idx].timing_power,
> + dmc->base_drexi1 + EXYNOS5_DREXI_TIMINGPOWER0);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_switch_timing_regs() - Changes bank register set for DRAM timings
> + * @dmc: device for which the new settings is going to be applied
> + * @set: boolean variable passing set value
> + *
> + * Changes the register set, which holds timing parameters.
> + * There is two register sets: 0 and 1. The register set 0
> + * is used in normal operation when the clock is provided from main PLL.
> + * The bank register set 1 is used when the main PLL frequency is going to be
> + * changed and the clock is taken from alternative, stable source.
> + * This function switches between these banks according to the
> + * currently used clock source.
> + */
> +static void exynos5_switch_timing_regs(struct exynos5_dmc *dmc, bool set)
> +{
> + unsigned int reg;
> +
> + reg = readl(dmc->base_clk + EXYNOS5_LPDDR3PHY_CON3);
> +
> + if (set)
> + reg |= EXYNOS5_TIMING_SET_SWI;
> + else
> + reg &= ~EXYNOS5_TIMING_SET_SWI;
> +
> + writel(reg, dmc->base_clk + EXYNOS5_LPDDR3PHY_CON3);
> +}
> +
> +/*
> + * Change clock parent for MUX_CORE_SEL and the main clock for DMC.
> + * The mux takes two clock sources: main BPLL and mx_mspll ('bypass').
> + */
> +static int exynos5_dmc_change_clock_parent(struct exynos5_dmc *dmc,
> + struct clk *parent,
> + unsigned int parent_selection_id)
> +{
> + unsigned int reg = 0;
> +
> + reg = readl(dmc->base_clk + EXYNOS5_CLK_SRC_CDREX);
> + if (clk_set_parent(dmc->mout_mclk_cdrex, parent)) {
> + dev_err(dmc->dev, "Couldn't change parent of mclk_cdrex\n");
> + return -EINVAL;
> + }
> +
> + for ( ; reg != parent_selection_id; ) {
> + cpu_relax();
> + reg = readl(dmc->base_clk + EXYNOS5_CLK_MUX_STAT_CDREX);
> + reg >>= EXYNOS5_CLKSRC_CDREX_SEL_SHIFT;
> + reg &= EXYNOS5_MCLK_CDREX_MASK;
> + }
> +
> + return 0;
> +}
> +
> +
> +/**
> + * exynos5_dmc_change_voltage() - Changes the voltage regulator value
> + * @dmc: device for which it is going to be set
> + * @target_volt: new voltage which is chosen to be final
> + *
> + * Main function for changing voltage on the VDD_MIF regulator.
> + */
> +static int exynos5_dmc_change_voltage(struct exynos5_dmc *dmc,
> + unsigned long target_volt)
> +{
> + int ret;
> +
> + ret = regulator_set_voltage(dmc->vdd_mif, target_volt,
> + target_volt + DMC_REG_VOLT_STEP);
> +
> + if (ret)
> + return ret;
> +
> + dmc->curr_volt = target_volt;
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_align_target_voltage() - Sets the final voltage for the DMC
> + * @dmc: device for which it is going to be set
> + * @target_volt: new voltage which is chosen to be final
> + *
> + * Function tries to align voltage to the safe level for 'normal' mode.
> + * It checks the need of higher voltage and changes the value. The target
> + * voltage might be lower that currently set and still the system will be
> + * stable.
> + */
> +static int exynos5_dmc_align_target_voltage(struct exynos5_dmc *dmc,
> + unsigned long target_volt)
> +{
> + int ret = 0;
> +
> + if (dmc->curr_volt > target_volt)
> + ret = exynos5_dmc_change_voltage(dmc, target_volt);
> +
> + return ret;
> +}
> +
> +/**
> + * exynos5_dmc_align_bypass_voltage() - Sets the voltage for the DMC
> + * @dmc: device for which it is going to be set
> + * @target_volt: new voltage which is chosen to be final
> + *
> + * Function tries to align voltage to the safe level for the 'bypass' mode.
> + * It checks the need of higher voltage and changes the value.
> + * The target voltage must not be less than currently needed, because
> + * for current frequency the device might become unstable.
> + */
> +static int exynos5_dmc_align_bypass_voltage(struct exynos5_dmc *dmc,
> + unsigned long target_volt)
> +{
> + int ret = 0;
> + unsigned long bypass_volt = dmc->opp_bypass->volt_uv;
> +
> + target_volt = max(bypass_volt, target_volt);
> +
> + if (dmc->curr_volt >= target_volt)
> + return 0;
> +
> + ret = exynos5_dmc_change_voltage(dmc, target_volt);
> +
> + return ret;
> +}
> +
> +/**
> + * exynos5_dmc_align_bypass_dram_timings() - Chooses and sets DRAM timings
> + * @dmc: device for which it is going to be set
> + * @target_rate: new frequency which is chosen to be final
> + *
> + * Function changes the DRAM timings for the temporary 'bypass' mode.
> + */
> +static int exynos5_dmc_align_bypass_dram_timings(struct exynos5_dmc *dmc,
> + unsigned long target_rate)
> +{
> + int idx = find_target_freq_idx(dmc, target_rate);
> +
> + if (idx < 0)
> + return -EINVAL;
> +
> + exynos5_set_bypass_dram_timings(dmc, dmc->dram_bypass_param);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_switch_to_bypass_configuration() - Switching to temporary clock
> + * @dmc: DMC device for which the switching is going to happen
> + * @target_rate: new frequency which is going to be set as a final
> + * @target_volt: new voltage which is going to be set as a final
> + *
> + * Function configures DMC and clocks for operating in temporary 'bypass' mode.
> + * This mode is used only temporary but if required, changes voltage and timings
> + * for DRAM chips. It switches the main clock to stable clock source for the
> + * period of the main PLL reconfiguration.
> + */
> +static int exynos5_dmc_switch_to_bypass_configuration(struct exynos5_dmc *dmc,
> + unsigned long target_rate,
> + unsigned long target_volt)
> +{
> + int ret;
> +
> + /*
> + * Having higher voltage for a particular frequency does not harm
> + * the chip. Use it for the temporary frequency change when one
> + * voltage manipulation might be avoided.
> + */
> + ret = exynos5_dmc_align_bypass_voltage(dmc, target_volt);
> + if (ret)
> + return ret;
> +
> + /*
> + * Longer delays for DRAM does not cause crash, the opposite does.
> + */
> + ret = exynos5_dmc_align_bypass_dram_timings(dmc, target_rate);
> + if (ret)
> + return ret;
> +
> + /*
> + * Delays are long enough, so use them for the new coming clock.
> + */
> + exynos5_switch_timing_regs(dmc, USE_MX_MSPLL_TIMINGS);
> +
> + /*
> + * Voltage is set at least to a level needed for this frequency,
> + * so switching clock source is safe now.
> + */
> + clk_prepare_enable(dmc->fout_spll);
> + clk_prepare_enable(dmc->mout_spll);
> + clk_prepare_enable(dmc->mout_mx_mspll_ccore);
> + ret = exynos5_dmc_change_clock_parent(dmc, dmc->mout_mx_mspll_ccore,
> + EXYNOS5_MCLK_CDREX_SEL_MX_MSPLL);
> + return ret;
> +}
> +
> +/**
> + * exynos5_dmc_change_freq_and_volt() - Changes voltage and frequency of the DMC
> + * using safe procedure
> + * @dmc: device for which the frequency is going to be changed
> + * @target_rate: requested new frequency
> + * @target_volt: requested voltage which corresponds to the new frequency
> + *
> + * The DMC frequency change procedure requires a few steps.
> + * The main requirement is to change the clock source in the clk mux
> + * for the time of main clock PLL locking. The assumption is that the
> + * alternative clock source set as parent is stable.
> + * The second parent's clock frequency is fixed to 400MHz, it is named 'bypass'
> + * clock. This requires alignment in DRAM timing parameters for the new
> + * T-period. There is two bank sets for keeping DRAM
> + * timings: set 0 and set 1. The set 0 is used when main clock source is
> + * chosen. The 2nd set of regs is used for 'bypass' clock. Switching between
> + * the two bank sets is part of the process.
> + * The voltage must also be aligned to the minimum required level. There is
> + * this intermediate step with switching to 'bypass' parent clock source.
> + * if the old voltage is lower, it requires an increase of the voltage level.
> + * The complexity of the voltage manipulation is hidden in low level function.
> + * In this function there is last alignment of the voltage level at the end.
> + */
> +static int
> +exynos5_dmc_change_freq_and_volt(struct exynos5_dmc *dmc,
> + unsigned long target_rate,
> + unsigned long target_volt)
> +{
> + int ret;
> +
> + ret = exynos5_dmc_switch_to_bypass_configuration(dmc, target_rate,
> + target_volt);
> + if (ret)
> + return ret;
> +
> + /* We are safe to increase the timings for current bypass frequency.
> + * Thanks to this the settings we be ready for the upcoming clock source
> + * change.
> + */
> + exynos5_dram_change_timings(dmc, target_rate);
> +
> + clk_set_rate(dmc->fout_bpll, target_rate * 1000);
> +
> + exynos5_switch_timing_regs(dmc, USE_BPLL_TIMINGS);
> +
> + ret = exynos5_dmc_change_clock_parent(dmc, dmc->mout_bpll,
> + EXYNOS5_MCLK_CDREX_SEL_BPLL);
> + if (ret)
> + return ret;
> +
> + clk_disable_unprepare(dmc->mout_mx_mspll_ccore);
> + clk_disable_unprepare(dmc->mout_spll);
> + clk_disable_unprepare(dmc->fout_spll);
> + /* Make sure if the voltage is not from 'bypass' settings and align to
> + * the right level for power efficiency.
> + */
> + ret = exynos5_dmc_align_target_voltage(dmc, target_volt);
> +
> + return ret;
> +}
> +
> +/**
> + * exynos5_dmc_get_volt_freq() - Gets the frequency and voltage from the OPP
> + * table.
> + * @dev: device for which the frequency is going to be changed
> + * @freq: requested frequency in KHz
> + * @target_rate: returned frequency which is the same or lower than
> + * requested
> + * @target_volt: returned voltage which corresponds to the returned
> + * frequency
> + *
> + * Function gets requested frequency and checks OPP framework for needed
> + * frequency and voltage. It populates the values 'target_rate' and
> + * 'target_volt' or returns error value when OPP framework fails.
> + */
> +static int exynos5_dmc_get_volt_freq(struct device *dev, unsigned long *freq,
> + unsigned long *target_rate,
> + unsigned long *target_volt, u32 flags)
> +{
> + struct dev_pm_opp *opp;
> +
> + opp = devfreq_recommended_opp(dev, freq, flags);
> + if (IS_ERR(opp))
> + return PTR_ERR(opp);
> +
> + *target_rate = dev_pm_opp_get_freq(opp);
> + *target_volt = dev_pm_opp_get_voltage(opp);
> + dev_pm_opp_put(opp);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_target() - Function responsible for changing frequency of DMC
> + * @dev: device for which the frequency is going to be changed
> + * @freq: requested frequency in KHz
> + * @flags: flags provided for this frequency change request
> + *
> + * An entry function provided to the devfreq framework which provides frequency
> + * change of the DMC. The function gets the possible rate from OPP table based
> + * on requested frequency. It calls the next function responsible for the
> + * frequency and voltage change. In case of failure, does not set 'curr_rate'
> + * and returns error value to the framework.
> + */
> +static int exynos5_dmc_target(struct device *dev, unsigned long *freq,
> + u32 flags)
> +{
> + struct exynos5_dmc *dmc = dev_get_drvdata(dev);
> + unsigned long target_rate = 0;
> + unsigned long target_volt = 0;
> + int ret;
> +
> + ret = exynos5_dmc_get_volt_freq(dev, freq, &target_rate, &target_volt,
> + flags);
> + if (ret)
> + return ret;
> +
> + if (target_rate == dmc->curr_rate)
> + return 0;
> +
> + mutex_lock(&dmc->lock);
> +
> + ret = exynos5_dmc_change_freq_and_volt(dmc, target_rate, target_volt);
> +
> + if (ret) {
> + mutex_unlock(&dmc->lock);
> + return ret;
> + }
> +
> + dmc->curr_rate = target_rate;
> +
> + mutex_unlock(&dmc->lock);
> + return 0;
> +}
> +
> +/**
> + * exynos5_cnt_name_match() - Tries to match 'edev' with the right device index
> + * @edev: event device for which the name is going to be matched
> + *
> + * Function matches the name of the 'edev' counter device with known devices
> + * with configured ratios and shares of the DMC channels.
> + * When the name is matched, it returns the index for the proper device.
> + */
> +static int exynos5_cnt_name_match(struct devfreq_event_dev *edev)
> +{
> + int i;
> + int id = -ENODEV;
> +
> + for (i = 0; i < ARRAY_SIZE(dmc_slot); i++) {
> + if (strstr(edev->desc->name, dmc_slot[i].name))
> + return i;
> + }
> +
> + return id;
> +}
> +
> +/**
> + * exynos5_cnt_calculate() - Calculates the values of performance counters.
> + * @edev: event device for which the counter is used for calculation
> + * @cnt: raw counter value
> + * @cnt_norm: counter value normalized to DMC performance ratio for a proper
> + * channel or virtual channel
> + *
> + * Function calculates normalized value for the raw counter. The raw counter
> + * value does not show real channel usage. The DMC splits not equally the
> + * bandwidth for the channels. The function checks the type of the 'edev'
> + * counter and calculates the normalized value based on the 'shares' of the
> + * bandwidth set in the controller.
> + */
> +static int exynos5_cnt_calculate(struct devfreq_event_dev *edev,
> + unsigned long cnt, u64 *cnt_norm)
> +{
> + int idx;
> +
> + idx = exynos5_cnt_name_match(edev);
> + if (idx < 0)
> + return idx;
> +
> + *cnt_norm = cnt;
> +
> + if (!(dmc_slot[idx].ratio_mul == dmc_slot[idx].ratio_div)) {
> + *cnt_norm = *cnt_norm * dmc_slot[idx].ratio_mul;
> + *cnt_norm = div_u64(*cnt_norm, dmc_slot[idx].ratio_div);
> + }
> +
> + *cnt_norm = *cnt_norm * PMCNT_CONST_RATIO_MUL;
> + *cnt_norm = div_u64(*cnt_norm, PMCNT_CONST_RATIO_DIV);
> +
> + return idx;
> +}
> +
> +/**
> + * exynos5_counters_get() - Gets the performance counters values.
> + * @dmc: device for which the counters are going to be checked
> + * @load_count: variable which is populated with counter value
> + * @total_count: variable which is used as 'wall clock' reference
> + *
> + * Function which provides performance counters values. It sums up counters for
> + * two DMC channels. The 'total_count' is used as a reference and max value.
> + * The ratio 'load_count/total_count' shows the busy percentage [0%, 100%].
> + */
> +static int exynos5_counters_get(struct exynos5_dmc *dmc,
> + unsigned long *load_count,
> + unsigned long *total_count)
> +{
> + unsigned long load_dmc[2] = {0, 0};
> + unsigned long total = 0;
> + u64 load = 0;
> + struct devfreq_event_data event;
> + int ret, i, idx;
> +
> + for (i = 0; i < dmc->num_counters; i++) {
> + if (!dmc->counter[i])
> + continue;
> +
> + ret = devfreq_event_get_event(dmc->counter[i], &event);
> + if (ret < 0)
> + return ret;
> +
> + idx = exynos5_cnt_calculate(dmc->counter[i], event.load_count,
> + &load);
> + if (idx < 0)
> + continue;
> +
> + if (idx == DMC0_0 || idx == DMC0_1)
> + load_dmc[0] += load;
> + else
> + load_dmc[1] += load;
> +
> + if (total < event.total_count)
> + total = event.total_count;
> + }
> +
> + *load_count = load_dmc[0] + load_dmc[1];
> + *total_count = total;
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_get_status() - Read current DMC performance statistics.
> + * @dev: device for which the statistics are requested
> + * @stat: structure which has statistic fields
> + *
> + * Function reads the DMC performance counters and calculates 'busy_time'
> + * and 'total_time'. To protect from overflow, the values are shifted right
> + * by 10. After read out the counters are setup to count again.
> + */
> +static int exynos5_dmc_get_status(struct device *dev,
> + struct devfreq_dev_status *stat)
> +{
> + struct exynos5_dmc *dmc = dev_get_drvdata(dev);
> + unsigned long load, total;
> + int ret;
> + bool cnt_en;
> +
> + mutex_lock(&dmc->lock);
> + cnt_en = dmc->counters_enabled;
> + mutex_unlock(&dmc->lock);
> + if (!cnt_en) {
> + dev_warn(dev, "performance counters needed, but not present\n");
> + return -EAGAIN;
> + }
> +
> + ret = exynos5_counters_get(dmc, &load, &total);
> + if (ret < 0)
> + return -EINVAL;
> +
> + /* To protect from overflow in calculation ratios, divide by 1024 */
> + stat->busy_time = load >> 10;
> + stat->total_time = total >> 10;
> +
> + ret = exynos5_counters_set_event(dmc);
> + if (ret < 0) {
> + dev_err(dmc->dev, "could not set event counter\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_get_cur_freq() - Function returns current DMC frequency
> + * @dev: device for which the framework checks operating frequency
> + * @freq: returned frequency value
> + *
> + * It returns the currently used frequency of the DMC. The real operating
> + * frequency might be lower when the clock source value could not be divided
> + * to the requested value.
> + */
> +static int exynos5_dmc_get_cur_freq(struct device *dev, unsigned long *freq)
> +{
> + struct exynos5_dmc *dmc = dev_get_drvdata(dev);
> +
> + mutex_lock(&dmc->lock);
> + *freq = dmc->curr_rate;
> + mutex_unlock(&dmc->lock);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_df_profile - Devfreq governor's profile structure
> + *
> + * It provides to the devfreq framework needed functions and polling period.
> + */
> +static struct devfreq_dev_profile exynos5_dmc_df_profile = {
> + .polling_ms = 500,
> + .target = exynos5_dmc_target,
> + .get_dev_status = exynos5_dmc_get_status,
> + .get_cur_freq = exynos5_dmc_get_cur_freq,
> +};
> +
> +/**
> + * exynos5_dmc_align_initial_frequency() - Align initial frequency value
> + * @dmc: device for which the frequency is going to be set
> + * @bootloader_init_freq: initial frequency set by the bootloader in KHz
> + *
> + * The initial bootloader frequency, which is present during boot, might be
> + * different that supported frequency values in the driver. It is possible
> + * due to different PLL settings or used PLL as a source.
> + * This function provides the 'initial_freq' for the devfreq framework
> + * statistics engine which supports only registered values. Thus, some alignment
> + * must be made.
> + */
> +unsigned long
> +exynos5_dmc_align_init_freq(struct exynos5_dmc *dmc,
> + unsigned long bootloader_init_freq)
> +{
> + unsigned long aligned_freq;
> + int idx;
> +
> + idx = find_target_freq_idx(dmc, bootloader_init_freq);
> + if (idx >= 0)
> + aligned_freq = dmc->opp[idx].freq_khz;
> + else
> + aligned_freq = dmc->opp[dmc->opp_count - 1].freq_khz;
> +
> + return aligned_freq;
> +}
> +
> +/**
> + * exynos5_dmc_init_clks() - Initialize clocks needed for DMC operation.
> + * @dev: device for which the clocks are setup
> + * @dmc: DMC structure containing needed fields
> + *
> + * Get the needed clocks defined in DT device, enable and set the right parents.
> + * Read current frequency and initialize the initial rate for governor.
> + */
> +static int exynos5_dmc_init_clks(struct device *dev, struct exynos5_dmc *dmc)
> +{
> + int ret;
> + unsigned long target_volt = 0;
> + unsigned long target_rate = 0;
> +
> + dmc->fout_spll = devm_clk_get(dev, "fout_spll");
> + if (IS_ERR(dmc->fout_spll))
> + return PTR_ERR(dmc->fout_spll);
> +
> + dmc->fout_bpll = devm_clk_get(dev, "fout_bpll");
> + if (IS_ERR(dmc->fout_bpll))
> + return PTR_ERR(dmc->fout_bpll);
> +
> + dmc->mout_mclk_cdrex = devm_clk_get(dev, "mout_mclk_cdrex");
> + if (IS_ERR(dmc->mout_mclk_cdrex))
> + return PTR_ERR(dmc->mout_mclk_cdrex);
> +
> + dmc->mout_bpll = devm_clk_get(dev, "mout_bpll");
> + if (IS_ERR(dmc->mout_bpll))
> + return PTR_ERR(dmc->mout_bpll);
> +
> + dmc->mout_mx_mspll_ccore = devm_clk_get(dev, "mout_mx_mspll_ccore");
> + if (IS_ERR(dmc->mout_mx_mspll_ccore))
> + return PTR_ERR(dmc->mout_mx_mspll_ccore);
> +
> + dmc->dout_clk2x_phy0 = devm_clk_get(dev, "dout_clk2x_phy0");
> + if (IS_ERR(dmc->dout_clk2x_phy0))
> + return PTR_ERR(dmc->dout_clk2x_phy0);
> +
> + dmc->mout_spll = devm_clk_get(dev, "ff_dout_spll2");
> + if (IS_ERR(dmc->mout_spll))
> + return PTR_ERR(dmc->mout_spll);
> +
> + /*
> + * Convert frequency to KHz values and set it for the governor.
> + */
> + dmc->curr_rate = clk_get_rate(dmc->mout_mclk_cdrex) / 1000;
> + dmc->curr_rate = exynos5_dmc_align_init_freq(dmc, dmc->curr_rate);
> + exynos5_dmc_df_profile.initial_freq = dmc->curr_rate;
> +
> + ret = exynos5_dmc_get_volt_freq(dev, &dmc->curr_rate, &target_rate,
> + &target_volt, 0);
> + if (ret)
> + return ret;
> +
> + dmc->curr_volt = target_volt;
> +
> + clk_prepare_enable(dmc->mout_spll);
> + clk_set_parent(dmc->mout_mx_mspll_ccore, dmc->mout_spll);
> + clk_prepare_enable(dmc->mout_mx_mspll_ccore);
> +
> + clk_prepare_enable(dmc->fout_bpll);
> + clk_prepare_enable(dmc->mout_bpll);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_performance_counters_init() - Initializes performance DMC's counters
> + * @dmc: DMC for which it does the setup
> + *
> + * Initialization of performance counters in DMC for estimating usage.
> + * The counter's values are used for calculation of a memory bandwidth and based
> + * on that the governor changes the frequency.
> + * The counters are not used when the governor is GOVERNOR_USERSPACE.
> + */
> +static int exynos5_performance_counters_init(struct exynos5_dmc *dmc)
> +{
> + int counters_size;
> + int ret, i;
> +
> + dmc->num_counters = devfreq_event_get_edev_count(dmc->dev);
> + if (dmc->num_counters < 0) {
> + dev_err(dmc->dev, "could not get devfreq-event counters\n");
> + return dmc->num_counters;
> + }
> +
> + counters_size = sizeof(struct devfreq_event_dev) * dmc->num_counters;
> + dmc->counter = devm_kzalloc(dmc->dev, counters_size, GFP_KERNEL);
> + if (!dmc->counter)
> + return -ENOMEM;
> +
> + for (i = 0; i < dmc->num_counters; i++) {
> + dmc->counter[i] =
> + devfreq_event_get_edev_by_phandle(dmc->dev, i);
> + if (IS_ERR_OR_NULL(dmc->counter[i]))
> + return -EPROBE_DEFER;
> + }
> +
> + ret = exynos5_counters_enable_edev(dmc);
> + if (ret < 0) {
> + dev_err(dmc->dev, "could not enable event counter\n");
> + return ret;
> + }
> +
> + ret = exynos5_counters_set_event(dmc);
> + if (ret < 0) {
> + dev_err(dmc->dev, "counld not set event counter\n");
> + return ret;
> + }
> +
> + mutex_lock(&dmc->lock);
> + dmc->counters_enabled = true;
> + mutex_unlock(&dmc->lock);
> +
> + return 0;
> +}
> +
> +/**
> + * exynos5_dmc_probe() - Probe function for the DMC driver
> + * @pdev: platform device for which the driver is going to be initialized
> + *
> + * Initialize basic components: clocks, regulators, performance counters, etc.
> + * Read out product version and based on the information setup
> + * internal structures for the controller (frequency and voltage) and for DRAM
> + * memory parameters: timings for each operating frequency.
> + * Register new devfreq device for controlling DVFS of the DMC.
> + */
> +static int exynos5_dmc_probe(struct platform_device *pdev)
> +{
> + int ret = 0;
> + struct exynos5_dmc *dmc;
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> +
> + dev_info(&pdev->dev, "DMC initializing\n");
Please do not pollute the log. Already exynos-bus creates a lot of
useless info messages for every bus. Maximum is one info message (at
the end of probe).
> +
> + dmc = devm_kzalloc(dev, sizeof(*dmc), GFP_KERNEL);
> + if (!dmc)
> + return -ENOMEM;
> +
> + mutex_init(&dmc->lock);
> +
> + dmc->dev = dev;
> + platform_set_drvdata(pdev, dmc);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + dmc->base_drexi0 = devm_ioremap_resource(dev, res);
> + if (IS_ERR(dmc->base_drexi0))
> + return PTR_ERR(dmc->base_drexi0);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + dmc->base_drexi1 = devm_ioremap_resource(dev, res);
> + if (IS_ERR(dmc->base_drexi1))
> + return PTR_ERR(dmc->base_drexi1);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> + dmc->base_clk = devm_ioremap_resource(dev, res);
> + if (IS_ERR(dmc->base_clk))
> + return PTR_ERR(dmc->base_clk);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
> + dmc->chip_id = devm_ioremap_resource(dev, res);
> + if (IS_ERR(dmc->chip_id))
> + return PTR_ERR(dmc->chip_id);
> +
> + ret = exynos5_dmc_chip_revision_settings(dmc);
> + if (ret)
> + return ret;
> +
> + ret = exynos5_init_freq_table(dev, dmc, &exynos5_dmc_df_profile);
> + if (ret)
> + return ret;
> +
> + dmc->vdd_mif = devm_regulator_get(dev, "vdd_mif");
> + if (IS_ERR(dmc->vdd_mif)) {
> + ret = PTR_ERR(dmc->vdd_mif);
> + dev_warn(dev, "couldn't get regulator\n");
> + goto remove_opp_table;
> + }
> +
> + ret = exynos5_dmc_init_clks(dev, dmc);
> + if (ret) {
> + dev_warn(dev, "couldn't initialize clocks\n");
> + goto remove_opp_table;
> + }
> +
> + ret = exynos5_dmc_pause_on_switching(dmc, 1);
> + if (ret) {
> + dev_warn(dev, "couldn't setup pause on switching\n");
> + goto remove_clocks;
> + }
> +
> + ret = exynos5_performance_counters_init(dmc);
> + if (ret) {
> + dev_warn(dev, "couldn't probe performance counters\n");
> + goto remove_clocks;
> + }
> + /*
> + * Setup default thresholds for the devfreq governor.
> + * The values are chosen based on experiments.
> + */
> + dmc->gov_data.upthreshold = 30;
> + dmc->gov_data.downdifferential = 5;
> +
> + dmc->df = devm_devfreq_add_device(dev, &exynos5_dmc_df_profile,
> + DEVFREQ_GOV_USERSPACE,
> + &dmc->gov_data);
> +
> + if (IS_ERR(dmc->df)) {
> + ret = PTR_ERR(dmc->df);
> + goto err_devfreq_add;
> + }
> +
> + ret = sysfs_create_group(&dmc->df->dev.kobj, &env_group);
> + if (ret) {
> + dev_err(dev, "couldn't add sysfs group\n");
> + goto err_devfreq_add;
1. debugfs instead of sysfs.
2. You are printing it during boot so why doing it here again?
> + }
> +
> + dev_info(&pdev->dev, "DMC init done\n");
I do not think it an as useful info. If you want to print something -
add at least some information. For example cpufreq does not print
anything because really there is no need. Therefore if you want -
print only exynos5_get_chip_info(), not 3 different messages.
> +
> + return 0;
> +
> +err_devfreq_add:
> + exynos5_counters_disable_edev(dmc);
> +remove_clocks:
> + clk_disable_unprepare(dmc->mout_mx_mspll_ccore);
> + clk_disable_unprepare(dmc->mout_spll);
> +remove_opp_table:
> + while (dmc->opp_count-- > 0)
> + dev_pm_opp_remove(dev, dmc->opp[dmc->opp_count].freq_khz);
> +
> + dev_warn(&pdev->dev, "DMC init failed\n");
No such warnings. They do not bring any information and core takes
care about this.
Best regards,
Krzysztof
Powered by blists - more mailing lists