linux-kernel - [PATCH v4 2/2] spi-atmel: support inter-word delay

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20190129083844.20572-3-jonas@norrbonn.se>
Date:   Tue, 29 Jan 2019 09:38:44 +0100
From:   Jonas Bonn <jonas@...rbonn.se>
To:     linux-kernel@...r.kernel.org
Cc:     Jonas Bonn <jonas@...rbonn.se>,
        Nicolas Ferre <nicolas.ferre@...rochip.com>,
        Mark Brown <broonie@...nel.org>,
        Alexandre Belloni <alexandre.belloni@...tlin.com>,
        Ludovic Desroches <ludovic.desroches@...rochip.com>,
        linux-spi@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: [PATCH v4 2/2] spi-atmel: support inter-word delay

If the SPI slave requires an inter-word delay, configure the DLYBCT
register accordingly.

Tested on a SAMA5D2 board (derived from SAMA5D2-Xplained reference
board).

Signed-off-by: Jonas Bonn <jonas@...rbonn.se>
CC: Nicolas Ferre <nicolas.ferre@...rochip.com>
CC: Mark Brown <broonie@...nel.org>
CC: Alexandre Belloni <alexandre.belloni@...tlin.com>
CC: Ludovic Desroches <ludovic.desroches@...rochip.com>
CC: linux-spi@...r.kernel.org
CC: linux-arm-kernel@...ts.infradead.org
---
 drivers/spi/spi-atmel.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)

diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 74fddcd3282b..6389a228d2f5 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -1209,13 +1209,21 @@ static int atmel_spi_setup(struct spi_device *spi)
 		csr |= SPI_BIT(CSAAT);
 
 	/* DLYBS is mostly irrelevant since we manage chipselect using GPIOs.
-	 *
-	 * DLYBCT would add delays between words, slowing down transfers.
-	 * It could potentially be useful to cope with DMA bottlenecks, but
-	 * in those cases it's probably best to just use a lower bitrate.
 	 */
 	csr |= SPI_BF(DLYBS, 0);
-	csr |= SPI_BF(DLYBCT, 0);
+
+	/* DLYBCT adds delays between words.  This is useful for slow devices
+	 * that need a bit of time to setup the next transfer.
+	 */
+	if (spi->word_delay_us) {
+		csr |= SPI_BF(DLYBCT,
+			clamp_t(u8,
+				(as->spi_clk/1000000*spi->word_delay_us)>>5,
+				1, 255));
+	} else {
+		csr |= SPI_BF(DLYBCT, 0);
+	}
+
 
 	/* chipselect must have been muxed as GPIO (e.g. in board setup) */
 	npcs_pin = (unsigned long)spi->controller_data;
-- 
2.19.1