| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ba7819abaa139dde1e79c3c862768f01a288624e.1549283920.git.matti.vaittinen@fi.rohmeurope.com>
Date: Mon, 4 Feb 2019 14:48:49 +0200
From: Matti Vaittinen <matti.vaittinen@...rohmeurope.com>
To: mazziesaccount@...il.com, matti.vaittinen@...rohmeurope.com
Cc: heikki.haikola@...rohmeurope.com, mikko.mutanen@...rohmeurope.com,
lee.jones@...aro.org, robh+dt@...nel.org, mark.rutland@....com,
broonie@...nel.org, gregkh@...uxfoundation.org, rafael@...nel.org,
mturquette@...libre.com, sboyd@...nel.org,
linus.walleij@...aro.org, bgolaszewski@...libre.com,
sre@...nel.org, lgirdwood@...il.com, a.zummo@...ertech.it,
alexandre.belloni@...tlin.com, wim@...ux-watchdog.org,
linux@...ck-us.net, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-clk@...r.kernel.org,
linux-gpio@...r.kernel.org, linux-pm@...r.kernel.org,
linux-rtc@...r.kernel.org, linux-watchdog@...r.kernel.org
Subject: [RFC PATCH v5 09/10] power: supply: Initial support for ROHM BD70528
PMIC charger block
ROHM BD70528 PMIC includes battery charger block. Support charger
staus queries and doing few basic settings like input current limit
and charging current.
Signed-off-by: Matti Vaittinen <matti.vaittinen@...rohmeurope.com>
---
drivers/power/supply/Kconfig | 9 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/bd70528-charger.c | 738 +++++++++++++++++++++++++++++++++
3 files changed, 748 insertions(+)
create mode 100644 drivers/power/supply/bd70528-charger.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index e901b9879e7e..903c97a67bf0 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
Say Y here to enable support for fuel gauge with SC27XX
PMIC chips.
+config CHARGER_BD70528
+ tristate "ROHM bd70528 charger driver"
+ depends on MFD_ROHM_BD70528
+ default n
+ help
+ Say Y here to enable support for getting battery status
+ information and altering charger configurations from charger
+ block of the ROHM BD70528 Power Management IC.
+
endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index b731c2a9b695..c60387b04bfa 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
+obj-$(CONFIG_CHARGER_BD70528) += bd70528-charger.o
diff --git a/drivers/power/supply/bd70528-charger.c b/drivers/power/supply/bd70528-charger.c
new file mode 100644
index 000000000000..db2824a9d960
--- /dev/null
+++ b/drivers/power/supply/bd70528-charger.c
@@ -0,0 +1,738 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+//
+// Copyright (C) 2018 ROHM Semiconductors
+//
+// power-supply driver for ROHM BD70528 PMIC
+
+/*
+ * BD70528 charger HW state machine.
+ *
+ * The thermal shutdown state is not drawn. From any other state but
+ * battery error and suspend it is possible to go to TSD/TMP states
+ * if temperature is out of bounds.
+ *
+ * CHG_RST = H
+ * or CHG_EN=L
+ * or (DCIN2_UVLO=L && DCIN1_UVLO=L)
+ * or (DCIN2_OVLO=H & DCIN1_UVKLO=L)
+ *
+ * +--------------+ +--------------+
+ * | | | |
+ * | Any state +-------> | Suspend |
+ * | | | |
+ * +--------------+ +------+-------+
+ * |
+ * CHG_EN = H && BAT_DET = H && |
+ * No errors (temp, bat_ov, UVLO, |
+ * OVLO...) |
+ * |
+ * BAT_OV or +---------v----------+
+ * (DBAT && TTRI) | |
+ * +-----------------+ Trickle Charge | <---------------+
+ * | | | |
+ * | +-------+------------+ |
+ * | | |
+ * | | ^ |
+ * | V_BAT > VTRI_TH | | VBAT < VTRI_TH - 50mV |
+ * | | | |
+ * | v | |
+ * | | |
+ * | BAT_OV or +----------+----+ |
+ * | (DBAT && TFST) | | |
+ * | +----------------+ Fast Charge | |
+ * | | | | |
+ * v v +----+----------+ |
+ * | |
+ *+----------------+ ILIM_DET=L | ^ ILIM_DET |
+ *| | & CV_DET=H | | or CV_DET=L |
+ *| Battery Error | & VBAT > | | or VBAT < VRECHG_TH |
+ *| | VRECHG_TH | | or IBAT > IFST/x |
+ *+----------------+ & IBAT < | | |
+ * IFST/x v | |
+ * ^ | |
+ * | +---------+-+ |
+ * | | | |
+ * +-------------------+ Top OFF | |
+ * BAT_OV = H or | | |
+ * (DBAT && TFST) +-----+-----+ |
+ * | |
+ * Stay top-off for 15s | |
+ * v |
+ * |
+ * +--------+ |
+ * | | |
+ * | Done +-------------------------+
+ * | |
+ * +--------+ VBAT < VRECHG_TH
+ */
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/rohm-bd70528.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+
+#define CHG_STAT_SUSPEND 0x0
+#define CHG_STAT_TRICKLE 0x1
+#define CHG_STAT_FAST 0x3
+#define CHG_STAT_TOPOFF 0xe
+#define CHG_STAT_DONE 0xf
+#define CHG_STAT_OTP_TRICKLE 0x10
+#define CHG_STAT_OTP_FAST 0x11
+#define CHG_STAT_OTP_DONE 0x12
+#define CHG_STAT_TSD_TRICKLE 0x20
+#define CHG_STAT_TSD_FAST 0x21
+#define CHG_STAT_TSD_TOPOFF 0x22
+#define CHG_STAT_BAT_ERR 0x7f
+
+static const char *bd70528_charger_model = "BD70528";
+static const char *bd70528_charger_manufacturer = "ROHM Semiconductors";
+
+#define BD_ERR_IRQ_HND(_name_, _wrn_) \
+static irqreturn_t bd0528_##_name_##_interrupt(int irq, void *arg) \
+{ \
+ struct power_supply *psy = (struct power_supply *)arg; \
+ \
+ power_supply_changed(psy); \
+ dev_err(&psy->dev, (_wrn_)); \
+ \
+ return IRQ_HANDLED; \
+}
+
+#define BD_INFO_IRQ_HND(_name_, _wrn_) \
+static irqreturn_t bd0528_##_name_##_interrupt(int irq, void *arg) \
+{ \
+ struct power_supply *psy = (struct power_supply *)arg; \
+ \
+ power_supply_changed(psy); \
+ dev_dbg(&psy->dev, (_wrn_)); \
+ \
+ return IRQ_HANDLED; \
+}
+
+#define BD_IRQ_HND(_name_) bd0528_##_name_##_interrupt
+
+struct bd70528_psy {
+ struct rohm_regmap_dev chip;
+ struct power_supply *psy;
+};
+
+BD_ERR_IRQ_HND(BAT_OV_DET, "Battery overvoltage detected\n");
+BD_ERR_IRQ_HND(DBAT_DET, "Dead battery detected\n");
+BD_ERR_IRQ_HND(COLD_DET, "Battery cold\n");
+BD_ERR_IRQ_HND(HOT_DET, "Battery hot\n");
+BD_ERR_IRQ_HND(CHG_TSD, "Charger thermal shutdown\n");
+BD_ERR_IRQ_HND(DCIN2_OV_DET, "DCIN2 overvoltage detected\n");
+
+BD_INFO_IRQ_HND(BAT_OV_RES, "Battery voltage back to normal\n");
+BD_INFO_IRQ_HND(COLD_RES, "Battery temperature back to normal\n");
+BD_INFO_IRQ_HND(HOT_RES, "Battery temperature back to normal\n");
+BD_INFO_IRQ_HND(BAT_RMV, "Battery removed\n");
+BD_INFO_IRQ_HND(BAT_DET, "Battery detected\n");
+BD_INFO_IRQ_HND(DCIN2_OV_RES, "DCIN2 voltage back to normal\n");
+BD_INFO_IRQ_HND(DCIN2_RMV, "DCIN2 removed\n");
+BD_INFO_IRQ_HND(DCIN2_DET, "DCIN2 detected\n");
+BD_INFO_IRQ_HND(DCIN1_RMV, "DCIN1 removed\n");
+BD_INFO_IRQ_HND(DCIN1_DET, "DCIN1 detected\n");
+
+struct irq_name_pair {
+ const char *n;
+ irqreturn_t (*h)(int irq, void *arg);
+};
+
+static int bd70528_get_irqs(struct platform_device *pdev,
+ struct bd70528_psy *bdpsy)
+{
+ int irq, i, ret;
+ unsigned int mask;
+ struct irq_name_pair bd70528_chg_irqs[] = {
+ { .n = "bd70528-bat-ov-res", .h = BD_IRQ_HND(BAT_OV_RES) },
+ { .n = "bd70528-bat-ov-det", .h = BD_IRQ_HND(BAT_OV_DET) },
+ { .n = "bd70528-bat-dead", .h = BD_IRQ_HND(DBAT_DET) },
+ { .n = "bd70528-bat-warmed", .h = BD_IRQ_HND(COLD_RES) },
+ { .n = "bd70528-bat-cold", .h = BD_IRQ_HND(COLD_DET) },
+ { .n = "bd70528-bat-cooled", .h = BD_IRQ_HND(HOT_RES) },
+ { .n = "bd70528-bat-hot", .h = BD_IRQ_HND(HOT_DET) },
+ { .n = "bd70528-chg-tshd", .h = BD_IRQ_HND(CHG_TSD) },
+ { .n = "bd70528-bat-removed", .h = BD_IRQ_HND(BAT_RMV) },
+ { .n = "bd70528-bat-detected", .h = BD_IRQ_HND(BAT_DET) },
+ { .n = "bd70528-dcin2-ov-res", .h = BD_IRQ_HND(DCIN2_OV_RES) },
+ { .n = "bd70528-dcin2-ov-det", .h = BD_IRQ_HND(DCIN2_OV_DET) },
+ { .n = "bd70528-dcin2-removed", .h = BD_IRQ_HND(DCIN2_RMV) },
+ { .n = "bd70528-dcin2-detected", .h = BD_IRQ_HND(DCIN2_DET) },
+ { .n = "bd70528-dcin1-removed", .h = BD_IRQ_HND(DCIN1_RMV) },
+ { .n = "bd70528-dcin1-detected", .h = BD_IRQ_HND(DCIN1_DET) },
+ };
+
+ for (i = 0; i < ARRAY_SIZE(bd70528_chg_irqs); i++) {
+ irq = platform_get_irq_byname(pdev, bd70528_chg_irqs[i].n);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "Bad IRQ information for %s (%d)\n",
+ bd70528_chg_irqs[i].n, irq);
+ return irq;
+ }
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ bd70528_chg_irqs[i].h,
+ IRQF_ONESHOT,
+ bd70528_chg_irqs[i].n,
+ bdpsy->psy);
+
+ if (ret)
+ return ret;
+ }
+ /*
+ * BD70528 irq controller is not touching the main mask register.
+ * So enable the charger block interrupts at main level. We can just
+ * leave them enabled as irq-controller should disable irqs
+ * from sub-registers when IRQ is disabled or freed.
+ */
+ mask = BD70528_REG_INT_BAT1_MASK | BD70528_REG_INT_BAT2_MASK;
+ ret = regmap_update_bits(bdpsy->chip.regmap,
+ BD70528_REG_INT_MAIN_MASK, mask, 0);
+ if (ret)
+ dev_err(&pdev->dev, "Failed to enable charger IRQs\n");
+
+ return ret;
+}
+
+static int bd70528_get_charger_status(struct bd70528_psy *bdpsy, int *val)
+{
+ int ret;
+ unsigned int v;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_CURR_STAT, &v);
+ if (ret) {
+ dev_err(bdpsy->chip.dev, "Charger state read failure %d\n",
+ ret);
+ return ret;
+ }
+
+ switch (v & BD70528_MASK_CHG_STAT) {
+ case CHG_STAT_SUSPEND:
+ /* Maybe we should check the CHG_TTRI_EN? */
+ case CHG_STAT_OTP_TRICKLE:
+ case CHG_STAT_OTP_FAST:
+ case CHG_STAT_OTP_DONE:
+ case CHG_STAT_TSD_TRICKLE:
+ case CHG_STAT_TSD_FAST:
+ case CHG_STAT_TSD_TOPOFF:
+ case CHG_STAT_BAT_ERR:
+ *val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ break;
+ case CHG_STAT_DONE:
+ *val = POWER_SUPPLY_STATUS_FULL;
+ break;
+ case CHG_STAT_TRICKLE:
+ case CHG_STAT_FAST:
+ case CHG_STAT_TOPOFF:
+ *val = POWER_SUPPLY_STATUS_CHARGING;
+ break;
+ default:
+ *val = POWER_SUPPLY_STATUS_UNKNOWN;
+ break;
+ }
+
+ return 0;
+}
+
+static int bd70528_get_charge_type(struct bd70528_psy *bdpsy, int *val)
+{
+ int ret;
+ unsigned int v;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_CURR_STAT, &v);
+ if (ret) {
+ dev_err(bdpsy->chip.dev, "Charger state read failure %d\n",
+ ret);
+ return ret;
+ }
+
+ switch (v & BD70528_MASK_CHG_STAT) {
+ case CHG_STAT_TRICKLE:
+ *val = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+ break;
+ case CHG_STAT_FAST:
+ case CHG_STAT_TOPOFF:
+ *val = POWER_SUPPLY_CHARGE_TYPE_FAST;
+ break;
+ case CHG_STAT_DONE:
+ case CHG_STAT_SUSPEND:
+ /* Maybe we should check the CHG_TTRI_EN? */
+ case CHG_STAT_OTP_TRICKLE:
+ case CHG_STAT_OTP_FAST:
+ case CHG_STAT_OTP_DONE:
+ case CHG_STAT_TSD_TRICKLE:
+ case CHG_STAT_TSD_FAST:
+ case CHG_STAT_TSD_TOPOFF:
+ case CHG_STAT_BAT_ERR:
+ *val = POWER_SUPPLY_CHARGE_TYPE_NONE;
+ break;
+ default:
+ *val = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+ break;
+ }
+
+ return 0;
+}
+
+static int bd70528_get_battery_health(struct bd70528_psy *bdpsy, int *val)
+{
+ int ret;
+ unsigned int v;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_BAT_STAT, &v);
+ if (ret) {
+ dev_err(bdpsy->chip.dev, "Battery state read failure %d\n",
+ ret);
+ return ret;
+ }
+ /* No battery? */
+ if (!(v & BD70528_MASK_CHG_BAT_DETECT))
+ *val = POWER_SUPPLY_HEALTH_DEAD;
+ else if (v & BD70528_MASK_CHG_BAT_OVERVOLT)
+ *val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ else if (v & BD70528_MASK_CHG_BAT_TIMER)
+ *val = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE;
+ else
+ *val = POWER_SUPPLY_HEALTH_GOOD;
+
+ return 0;
+}
+
+static int bd70528_get_online(struct bd70528_psy *bdpsy, int *val)
+{
+ int ret;
+ unsigned int v;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_IN_STAT, &v);
+ if (ret) {
+ dev_err(bdpsy->chip.dev, "DC1 IN state read failure %d\n",
+ ret);
+ return ret;
+ }
+
+ *val = (v & BD70528_MASK_CHG_DCIN1_UVLO) ? 1 : 0;
+
+ return 0;
+}
+
+static int bd70528_get_present(struct bd70528_psy *bdpsy, int *val)
+{
+ int ret;
+ unsigned int v;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_BAT_STAT, &v);
+ if (ret) {
+ dev_err(bdpsy->chip.dev, "Battery state read failure %d\n",
+ ret);
+ return ret;
+ }
+
+ *val = (v & BD70528_MASK_CHG_BAT_DETECT) ? 1 : 0;
+
+ return 0;
+}
+
+struct linear_range {
+ int min;
+ int step;
+ int vals;
+ int low_sel;
+};
+
+struct linear_range current_limit_ranges[] = {
+ {
+ .min = 5,
+ .step = 1,
+ .vals = 36,
+ .low_sel = 0,
+ },
+ {
+ .min = 40,
+ .step = 5,
+ .vals = 5,
+ .low_sel = 0x23,
+ },
+ {
+ .min = 60,
+ .step = 20,
+ .vals = 8,
+ .low_sel = 0x27,
+ },
+ {
+ .min = 200,
+ .step = 50,
+ .vals = 7,
+ .low_sel = 0x2e,
+ }
+};
+
+/*
+ * BD70528 would support setting and getting own charge current/
+ * voltage for low temperatures. The driver currently only reads
+ * the charge current at room temperature. We do set both though.
+ */
+struct linear_range warm_charge_curr[] = {
+ {
+ .min = 10,
+ .step = 10,
+ .vals = 20,
+ .low_sel = 0,
+ },
+ {
+ .min = 200,
+ .step = 25,
+ .vals = 13,
+ .low_sel = 0x13,
+ },
+};
+
+/*
+ * Cold charge current selectors are identical to warm charge current
+ * selectors. The difference is that only smaller currents are available
+ * at cold charge range.
+ */
+#define MAX_COLD_CHG_CURR_SEL 0x15
+#define MAX_WARM_CHG_CURR_SEL 0x1f
+#define MIN_CHG_CURR_SEL 0x0
+
+static int find_value_for_selector_low(struct linear_range *r, int selectors,
+ unsigned int sel, unsigned int *val)
+{
+ int i;
+
+ for (i = 0; i < selectors; i++) {
+ if (r[i].low_sel <= sel && r[i].low_sel + r[i].vals >= sel) {
+ *val = r[i].min + (sel - r[i].low_sel) * r[i].step;
+ return 0;
+ }
+
+ }
+ return -EINVAL;
+}
+
+/*
+ * For BD70528 voltage/current limits we happily accept any value which
+ * belongs the range. We could check if value matching the selector is
+ * desired by computing the range min + (sel - sel_low) * range step - but
+ * I guess it is enough if we use voltage/current which is closest (below)
+ * the requested?
+ */
+static int find_selector_for_value_low(struct linear_range *r, int selectors,
+ unsigned int val, unsigned int *sel,
+ bool *found)
+{
+ int i;
+ int ret = -EINVAL;
+
+ *found = false;
+ for (i = 0; i < selectors; i++) {
+ if (r[i].min <= val) {
+ if (r[i].min + r[i].step * r[i].vals >= val) {
+ *found = true;
+ *sel = r[i].low_sel + (val - r[i].min) /
+ r[i].step;
+ ret = 0;
+ break;
+ }
+ /*
+ * If the range max is smaller than requested
+ * we can set the max supported value from range
+ */
+ *sel = r[i].low_sel + r[i].vals;
+ ret = 0;
+ }
+ }
+ return ret;
+}
+
+static int get_charge_current(struct bd70528_psy *bdpsy, int *ma)
+{
+ unsigned int sel;
+ int ret;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_CHG_CURR_WARM,
+ &sel);
+ if (ret) {
+ dev_err(bdpsy->chip.dev,
+ "Charge current reading failed (%d)\n", ret);
+ return ret;
+ }
+
+ sel &= BD70528_MASK_CHG_CHG_CURR;
+
+ ret = find_value_for_selector_low(&warm_charge_curr[0],
+ ARRAY_SIZE(warm_charge_curr), sel,
+ ma);
+ if (ret) {
+ dev_err(bdpsy->chip.dev,
+ "Unknown charge current value 0x%x\n",
+ sel);
+ }
+
+ return ret;
+}
+
+static int get_current_limit(struct bd70528_psy *bdpsy, int *ma)
+{
+ unsigned int sel;
+ int ret;
+
+ ret = regmap_read(bdpsy->chip.regmap, BD70528_REG_CHG_DCIN_ILIM,
+ &sel);
+
+ if (ret) {
+ dev_err(bdpsy->chip.dev,
+ "Input current limit reading failed (%d)\n", ret);
+ return ret;
+ }
+
+ sel &= BD70528_MASK_CHG_DCIN_ILIM;
+
+ ret = find_value_for_selector_low(¤t_limit_ranges[0],
+ ARRAY_SIZE(current_limit_ranges), sel,
+ ma);
+
+ if (ret) {
+ /* Unspecified values mean 500 mA */
+ *ma = 500;
+ }
+ return 0;
+}
+
+static enum power_supply_property bd70528_charger_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_CHARGE_TYPE,
+ POWER_SUPPLY_PROP_HEALTH,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+ POWER_SUPPLY_PROP_MODEL_NAME,
+ POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static int bd70528_charger_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct bd70528_psy *bdpsy = power_supply_get_drvdata(psy);
+ int ret = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ return bd70528_get_charger_status(bdpsy, &val->intval);
+ case POWER_SUPPLY_PROP_CHARGE_TYPE:
+ return bd70528_get_charge_type(bdpsy, &val->intval);
+ case POWER_SUPPLY_PROP_HEALTH:
+ return bd70528_get_battery_health(bdpsy, &val->intval);
+ case POWER_SUPPLY_PROP_PRESENT:
+ return bd70528_get_present(bdpsy, &val->intval);
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ ret = get_current_limit(bdpsy, &val->intval);
+ val->intval *= 1000;
+ return ret;
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+ ret = get_charge_current(bdpsy, &val->intval);
+ val->intval *= 1000;
+ return ret;
+ case POWER_SUPPLY_PROP_ONLINE:
+ return bd70528_get_online(bdpsy, &val->intval);
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = bd70528_charger_model;
+ return 0;
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = bd70528_charger_manufacturer;
+ return 0;
+ default:
+ break;
+ }
+
+ return -EINVAL;
+}
+
+static int bd70528_prop_is_writable(struct power_supply *psy,
+ enum power_supply_property psp)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+ return 1;
+ default:
+ break;
+ }
+ return 0;
+}
+
+
+
+static int set_charge_current(struct bd70528_psy *bdpsy, int ma)
+{
+ unsigned int reg;
+ int ret = 0, tmpret;
+ bool found;
+
+ if (ma > 500) {
+ dev_warn(bdpsy->chip.dev,
+ "Requested charge current %u exceed maximum (500mA)\n",
+ ma);
+ reg = MAX_WARM_CHG_CURR_SEL;
+ goto set;
+ }
+ if (ma < 10) {
+ dev_err(bdpsy->chip.dev,
+ "Requested charge current %u smaller than min (10mA)\n",
+ ma);
+ reg = MIN_CHG_CURR_SEL;
+ ret = -EINVAL;
+ goto set;
+ }
+
+ ret = find_selector_for_value_low(&warm_charge_curr[0],
+ ARRAY_SIZE(warm_charge_curr), ma,
+ ®, &found);
+
+ if (!found) {
+ /* There was a gap in supported values and we hit it */
+ dev_warn(bdpsy->chip.dev,
+ "Unsupported charge current %u mA\n", ma);
+ }
+set:
+
+ tmpret = regmap_update_bits(bdpsy->chip.regmap,
+ BD70528_REG_CHG_CHG_CURR_WARM,
+ BD70528_MASK_CHG_CHG_CURR, reg);
+ if (tmpret)
+ dev_err(bdpsy->chip.dev,
+ "Charge current write failure (%d)\n", tmpret);
+
+ if (reg > MAX_COLD_CHG_CURR_SEL)
+ reg = MAX_COLD_CHG_CURR_SEL;
+
+ if (!tmpret)
+ tmpret = regmap_update_bits(bdpsy->chip.regmap,
+ BD70528_REG_CHG_CHG_CURR_COLD,
+ BD70528_MASK_CHG_CHG_CURR, reg);
+
+ if (!ret)
+ ret = tmpret;
+
+ return ret;
+}
+
+#define MAX_CURR_LIMIT_SEL 0x34
+#define MIN_CURR_LIMIT_SEL 0x0
+
+static int set_current_limit(struct bd70528_psy *bdpsy, int ma)
+{
+ unsigned int reg;
+ int ret = 0, tmpret;
+ bool found;
+
+ if (ma > 500) {
+ dev_warn(bdpsy->chip.dev,
+ "Requested current limit %u exceed maximum (500mA)\n",
+ ma);
+ reg = MAX_CURR_LIMIT_SEL;
+ goto set;
+ }
+ if (ma < 5) {
+ dev_err(bdpsy->chip.dev,
+ "Requested current limit %u smaller than min (5mA)\n",
+ ma);
+ reg = MIN_CURR_LIMIT_SEL;
+ ret = -EINVAL;
+ goto set;
+ }
+
+ ret = find_selector_for_value_low(¤t_limit_ranges[0],
+ ARRAY_SIZE(current_limit_ranges), ma,
+ ®, &found);
+ if (!found) {
+ /* There was a gap in supported values and we hit it ?*/
+ dev_warn(bdpsy->chip.dev, "Unsupported current limit %umA\n",
+ ma);
+ }
+
+set:
+ tmpret = regmap_update_bits(bdpsy->chip.regmap,
+ BD70528_REG_CHG_DCIN_ILIM,
+ BD70528_MASK_CHG_DCIN_ILIM, reg);
+
+ if (!ret)
+ ret = tmpret;
+
+ return ret;
+}
+
+static int bd70528_charger_set_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ const union power_supply_propval *val)
+{
+ struct bd70528_psy *bdpsy = power_supply_get_drvdata(psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+ return set_current_limit(bdpsy, val->intval / 1000);
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+ return set_charge_current(bdpsy, val->intval / 1000);
+ default:
+ break;
+ }
+ return -EINVAL;
+}
+
+static const struct power_supply_desc bd70528_charger_desc = {
+ .name = "bd70528-charger",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = bd70528_charger_props,
+ .num_properties = ARRAY_SIZE(bd70528_charger_props),
+ .get_property = bd70528_charger_get_property,
+ .set_property = bd70528_charger_set_property,
+ .property_is_writeable = bd70528_prop_is_writable,
+};
+
+static int bd70528_power_probe(struct platform_device *pdev)
+{
+ struct rohm_regmap_dev *mfd;
+ struct bd70528_psy *bdpsy;
+ struct power_supply_config cfg = {};
+
+ mfd = dev_get_drvdata(pdev->dev.parent);
+ if (!mfd) {
+ dev_err(&pdev->dev, "No MFD driver data\n");
+ return -EINVAL;
+ }
+ bdpsy = devm_kzalloc(&pdev->dev, sizeof(*bdpsy), GFP_KERNEL);
+ if (!bdpsy)
+ return -ENOMEM;
+ bdpsy->chip = *mfd;
+ bdpsy->chip.dev = &pdev->dev;
+
+ platform_set_drvdata(pdev, bdpsy);
+ cfg.drv_data = bdpsy;
+ cfg.of_node = pdev->dev.parent->of_node;
+
+ bdpsy->psy = devm_power_supply_register(&pdev->dev,
+ &bd70528_charger_desc, &cfg);
+ if (IS_ERR(bdpsy->psy)) {
+ dev_err(&pdev->dev, "failed: power supply register\n");
+ return PTR_ERR(bdpsy->psy);
+ }
+
+ return bd70528_get_irqs(pdev, bdpsy);
+}
+
+static struct platform_driver bd70528_power = {
+ .driver = {
+ .name = "bd70528-power"
+ },
+ .probe = bd70528_power_probe,
+};
+
+module_platform_driver(bd70528_power);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@...rohmeurope.com>");
+MODULE_DESCRIPTION("BD70528 power-supply driver");
+MODULE_LICENSE("GPL");
--
2.14.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then, he vanished ~~~
Powered by blists - more mailing lists