| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <790ea13b-7a44-2452-a6b2-51102e60c290@samsung.com>
Date: Mon, 11 Feb 2019 19:34:58 +0900
From: Chanwoo Choi <cw00.choi@...sung.com>
To: Lukasz Luba <l.luba@...tner.samsung.com>, cwchoi00@...il.com
Cc: devicetree <devicetree@...r.kernel.org>,
linux-kernel <linux-kernel@...r.kernel.org>,
Linux PM list <linux-pm@...r.kernel.org>,
linux-samsung-soc <linux-samsung-soc@...r.kernel.org>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
Krzysztof Kozlowski <krzk@...nel.org>,
Kukjin Kim <kgene@...nel.org>,
Kyungmin Park <kyungmin.park@...sung.com>,
Marek Szyprowski <m.szyprowski@...sung.com>,
Sylwester Nawrocki <s.nawrocki@...sung.com>,
MyungJoo Ham <myungjoo.ham@...sung.com>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...nel.org>, linux-clk@...r.kernel.org,
linux-arm-kernel <linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v3 3/8] clk: samsung: add BPLL rate table for Exynos
5422 SoC
Hi Lukasz,
On 19. 2. 11. 오후 7:21, Lukasz Luba wrote:
> Hi Chanwoo,
>
> On 2/3/19 8:54 AM, Chanwoo Choi wrote:
>> Hi Lukasz,
>>
>> 2019년 2월 1일 (금) 오후 11:22, Lukasz Luba <l.luba@...tner.samsung.com>님이 작성:
>>
>>>
>>> Hi Chanwoo,
>>>
>>> On 2/1/19 9:44 AM, Chanwoo Choi wrote:
>>>> Hi,
>>>>
>>>> On 19. 1. 31. 오후 5:49, Lukasz Luba wrote:
>>>>> Add new table rate for BPLL for Exynos5422 SoC supporting Dynamic Memory
>>>>> Controller frequencies for driver's DRAM timings.
>>>>>
>>>>> CC: Sylwester Nawrocki <s.nawrocki@...sung.com>
>>>>> CC: Chanwoo Choi <cw00.choi@...sung.com>
>>>>> CC: Michael Turquette <mturquette@...libre.com>
>>>>> CC: Stephen Boyd <sboyd@...nel.org>
>>>>> CC: Kukjin Kim <kgene@...nel.org>
>>>>> CC: Krzysztof Kozlowski <krzk@...nel.org>
>>>>> CC: linux-samsung-soc@...r.kernel.org
>>>>> CC: linux-clk@...r.kernel.org
>>>>> CC: linux-arm-kernel@...ts.infradead.org
>>>>> CC: linux-kernel@...r.kernel.org
>>>>> Signed-off-by: Lukasz Luba <l.luba@...tner.samsung.com>
>>>>> ---
>>>>> drivers/clk/samsung/clk-exynos5420.c | 15 ++++++++++++++-
>>>>> 1 file changed, 14 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c
>>>>> index 3e87421..8bf9579 100644
>>>>> --- a/drivers/clk/samsung/clk-exynos5420.c
>>>>> +++ b/drivers/clk/samsung/clk-exynos5420.c
>>>>> @@ -1325,6 +1325,19 @@ static const struct samsung_pll_rate_table exynos5420_pll2550x_24mhz_tbl[] __ini
>>>>> PLL_35XX_RATE(24 * MHZ, 200000000, 200, 3, 3),
>>>>> };
>>>>>
>>>>> +static const struct samsung_pll_rate_table exynos5422_bpll_rate_table[] = {
>>>>> + PLL_35XX_RATE(24 * MHZ, 933000000, 311, 4, 1),
>>>>> + PLL_35XX_RATE(24 * MHZ, 825000000, 275, 4, 1),
>>>>> + PLL_35XX_RATE(24 * MHZ, 728000000, 182, 3, 1),
>>>>> + PLL_35XX_RATE(24 * MHZ, 633000000, 211, 4, 1),
>>>>> + PLL_35XX_RATE(24 * MHZ, 543000000, 181, 2, 2),
>>>>> + PLL_35XX_RATE(24 * MHZ, 413000000, 413, 6, 2),
>>>>> + PLL_35XX_RATE(24 * MHZ, 275000000, 275, 3, 3),
>>>>> + PLL_35XX_RATE(24 * MHZ, 206000000, 206, 3, 3),
>>>>> + PLL_35XX_RATE(24 * MHZ, 165000000, 110, 2, 3),
>>>>> + PLL_35XX_RATE(24 * MHZ, 138000000, 184, 2, 4),
>>>>
>>>> Except for 825Mhz, I can't find the target frequency
>>>> on Exynos5422 TRM document. Usually, Exynos TRM specified
>>>> the supported stable clocks. It means that undefined clocks
>>>> are not stable as I knew. Where do you find them?
>>>>
>>>> When I calculated the PLL frequency with PMS value, it is correct.
>>>> But, just we need to check the reference of undefined clocks on TRM
>>>> in order to guarantee the stable operation.
>>> They values live in vendor code for Android.
>>> I have tested the DMC & DDR with these ratios in stress scenarios
>>> for a few days and it was stable.
>>
>> If possible, please share the url of original vendor code.
> Here is the vendor code for the BPLL values:
> https://github.com/hardkernel/linux/blob/odroidxu3-3.10.y-android/drivers/clk/samsung/clk-exynos5422.c#L2026
Thanks for sharing.
bpll_rate_table has two different supported frequency
according to exynos5422 revision as following:
But, this patch only has only one frequency set
for CONFIG_SOC_EXYNOS5422_REV_0.
Could you guarantee that all Exynos5422-based Odroid-xu3 board
has CONFIG_SOC_EXYNOS5422_REV_0 ersion? If not guaranteed,
some board might be fault because of using the unsupported
frequencies.
It is dangerous and unstable to use the unsupported frequencies to SoC.
struct samsung_pll_rate_table bpll_rate_table[] = {
/* rate p m s k */
#ifdef CONFIG_SOC_EXYNOS5422_REV_0
{ 933000000U, 4, 311, 1, 0},
{ 925000000U, 4, 307, 1, 0},
{ 825000000U, 4, 275, 1, 0},
{ 728000000U, 3, 182, 1, 0},
{ 633000000U, 4, 211, 1, 0},
{ 543000000U, 2, 181, 2, 0},
{ 413000000U, 6, 413, 2, 0},
{ 275000000U, 3, 275, 3, 0},
{ 206000000U, 3, 206, 3, 0},
{ 165000000U, 2, 110, 3, 0},
{ 138000000U, 2, 184, 4, 0},
#else
{ 933000000U, 4, 311, 1, 0},
{ 800000000U, 3, 200, 1, 0},
{ 733000000U, 2, 122, 1, 0},
{ 667000000U, 2, 111, 1, 0},
{ 533000000U, 3, 266, 2, 0},
{ 400000000U, 3, 200, 2, 0},
{ 266000000U, 3, 266, 3, 0},
{ 200000000U, 3, 200, 3, 0},
{ 160000000U, 3, 160, 3, 0},
#endif
};
>
> Regards,
> Lukasz
>>
>>>
>>>>
>>>> Remove 933/138Mhz because exynos5433-dmc.c doesn't use 933Mhz and 138Mhz
>>>> and also Exynos5422 TRM doesn't define 933/138Mhz on pll table.
>>> OK, I will remove them.
>>>>
>>>>> +};
>>>>> +
>>>>> static const struct samsung_pll_rate_table exynos5420_epll_24mhz_tbl[] = {
>>>>> PLL_36XX_RATE(24 * MHZ, 600000000U, 100, 2, 1, 0),
>>>>> PLL_36XX_RATE(24 * MHZ, 400000000U, 200, 3, 2, 0),
>>>>> @@ -1467,7 +1480,7 @@ static void __init exynos5x_clk_init(struct device_node *np,
>>>>> exynos5x_plls[apll].rate_table = exynos5420_pll2550x_24mhz_tbl;
>>>>> exynos5x_plls[epll].rate_table = exynos5420_epll_24mhz_tbl;
>>>>> exynos5x_plls[kpll].rate_table = exynos5420_pll2550x_24mhz_tbl;
>>>>> - exynos5x_plls[bpll].rate_table = exynos5420_pll2550x_24mhz_tbl;
>>>>> + exynos5x_plls[bpll].rate_table = exynos5422_bpll_rate_table;
>>>>
>>>> Exynos5422 used the same PLL table for apll, kpll, bpll and so on.
>>>> You don't need to make the separate pll table. Just add new entries
>>>> to exynos5420_pll2550x_24mhz_tbl table.
>>> OK, I will extend the exynos5420_pll2550x_24mhz_tbl table.
>>>
>>> In v4 patch set, it will be fixed.
>>>
>>> Regards,
>>> Lukasz
>>>>
>>>>> }
>>>>>
>>>>> samsung_clk_register_pll(ctx, exynos5x_plls, ARRAY_SIZE(exynos5x_plls),
>>>>>
>>>>
>>
>>
>>
>> --
>> Best Regards,
>> Chanwoo Choi
>> Samsung Electronics
>>
>>
>
>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
Powered by blists - more mailing lists